Milwaukee 2451-20 Manual de Usario

Milwaukee maquina de atornillar 2451-20

Lee a continuación 📖 el manual en español para Milwaukee 2451-20 (9 páginas) en la categoría maquina de atornillar. Esta guía fue útil para 9 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/9

OPERATOR'S MANUAL

MANUEL de L'UTILISATEUR

MANUAL del OPERADOR

Cat. No.

No de cat.

2450-20

2451-20

TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S

MANUAL.

AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE ET BIEN

COMPRENDRE LE MANUEL DE L'UTILISATEUR.

PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER Y ENTENDER EL

MANUAL DEL OPERADOR.

M12™ CORDLESS IMPACT WRENCH AND IMPACT DRIVER

CLÉS À CHOCS ET VISSEUSE M12™

LLAVES DE IMPACTO E IMPULSOR DE IMPACTO DE M12™

• Hold power tool by insulated gripping sur-

faces, when performing an operation where the

fastener may contact hidden wiring. Fasteners

contacting a “live” wire may make exposed metal

parts of the power tool “live” and could give the

operator an electric shock.

• Wear ear protectors. Exposure to noise can

cause hearing loss.

• Keep hands away from all cutting edges and

moving parts.

• Maintain labels and nameplates. These carry

important information. If unreadable or missing,

contact a MILWAUKEE service facility for a free

replacement.

• WARNING: Some dust created by power sanding,

sawing, grinding, drilling, and other construction

activities contains chemicals known to cause

cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

• lead from lead-based paint

• crystalline silica from bricks and cement and other

masonry products, and

•

arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending

on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well

ventilated area, and work with approved safety

equipment, such as those dust masks that are spe-

cially designed to ﬁ lter out microscopic particles.

FUNCTIONAL DESCRIPTION

ASSEMBLY

WARNING Recharge only with the

charger speciﬁ ed for the battery. For speciﬁ c

charging instructions, read the operator’s

manual supplied with your charger and battery.

Inserting/Removing the Battery

To remove the battery, push in the release buttons

and pull the battery pack away from the tool.

To insert the battery, slide the pack into the body of

the tool. Make sure it latches securely into place.

SYMBOLOGY

SPECIFICATIONS

Cat. No. Volts DC RPM Drive Shank IPM

2450-20

2451-20

0-2 000

1/4" Hex

3/8" Square

0-3 000

Volts

Direct Current

Impacts per Minute Under Load

(IPM)

No Load Revolutions per Minute

(RPM)

Underwriters Laboratories, Inc.

United States and Canada

WARNING Use only sockets and other

accessories speciﬁ cally designed for use on

impact wrenches and drivers. Other sockets

and accessories might shatter or break caus-

ing injury.

Attaching and Removing Accessories

These tools are intended only for use with acces-

sories designed for impact wrenches and drivers.

Other sockets could shatter or break, causing injury.

Cat. No. 2450-20

This driver is intended for use with drill

and driver bits with a 1/4” hex shank and

ball detent recess.

1. To attach an accessory, pull the ring

out and insert the accessory shank.

Release the ring. It may be necessary

to pull the bit out slightly to engage the

holding mechanism.

2. To remove the accessory, pull out the ring and

remove the accessory. Release the ring.

WARNING Always remove battery

pack before changing or removing accesso-

ries. Only use accessories speciﬁ cally recom-

mended for this tool. Others may be hazardous.

PERSONAL SAFETY

GENERAL POWER TOOL SAFETY WARNINGS

WORK AREA SAFETY

ELECTRICAL SAFETY

• Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

• Do not operate power tools in explosive at-

mospheres, such as in the presence of ﬂ am-

mable liquids, gases or dust. Power tools create

sparks which may ignite the dust or fumes.

• Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

• Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodiﬁ ed plugs and matching outlets will

reduce risk of electric shock.

• Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet condi-

tions. Water entering a power tool will increase

the risk of electric shock.

• Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges

or moving parts. Damaged or entangled cords

increase the risk of electric shock.

• When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use

of a cord suitable for outdoor use reduces the risk

of electric shock.

• If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD reduces

the risk of electric shock.

attached to a rotating part of the power tool may

result in personal injury.

• Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewel-

lery or long hair can be caught in moving parts.

• If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use of

dust collection can reduce dust-related hazards.

WARNING READ ALL SAFETY WARNINGS AND ALL INSTRUCTIONS.

Failure to follow the warnings and instructions may result in electric shock, ﬁ re and/or

serious injury. Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

POWER TOOL USE AND CARE

• Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at the

rate for which it was designed.

• Do not use the power tool if the switch does not

turn it on and o. Any power tool that cannot be

controlled with the switch is dangerous and must

be repaired.

• Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such

preventive safety measures reduce the risk of

starting the power tool accidentally.

• Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with

the power tool or these instructions to operate

the power tool. Power tools are dangerous in the

hands of untrained users.

• Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may affect the

power tool’s operation. If damaged, have the

power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

• Use the power tool, accessories and tool bits

etc., in accordance with these instructions,

taking into account the working conditions and

the work to be performed. Use of the power tool

for operations dierent from those intended could

result in a hazardous situation.

• Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use a power tool while you are tired or under

the inﬂ uence of drugs, alcohol or medication. A

moment of inattention while operating power tools

may result in serious personal injury.

• Use personal protective equipment. Always

wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate conditions

will reduce personal injuries.

• Prevent unintentional starting. Ensure the

switch is in the o-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools with

your ﬁ nger on the switch or energising power tools

that have the switch on invites accidents.

• Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

• Recharge only with the charger speciﬁ ed by

the manufacturer. A charger that is suitable for

one type of battery pack may create a risk of ﬁ re

when used with another battery pack.

• Use power tools only with speciﬁ cally desig-

nated battery packs. Use of any other battery

packs may create a risk of injury and ﬁ re.

BATTERY TOOL USE AND CARE

SPECIFIC SAFETY RULES

• When battery pack is not in use, keep it away

from other metal objects like paper clips,

coins, keys, nails, screws, or other small metal

objects that can make a connection from one

terminal to another. Shorting the battery termi-

nals together may cause burns or a ﬁ re.

•

Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact ac-

cidentally occurs, ﬂ ush with water. If liquid con-

tacts eyes, additionally seek medical help. Liquid

ejected from the battery may cause irritation or burns.

SERVICE

• Have your power tool serviced by a qualiﬁ ed

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool is maintained.

Cat. No. 2451-20

1. Use only 3/8" Square Drive Sockets.

2. To attach a socket, align the accessory with the

drive shank and push it ﬁ rmly over the retaining ring.

3. To remove the accessory, pull the accessory o

the drive shank.

1. Trigger

2. Control switch

3. LED

4. Drive Shank

5. Fuel Gauge

ing. Be particularly careful when impacting smaller

fasteners because they require less impacting to

reach optimum torque.

Practice with various fasteners, noting the length of

time required to reach the desired torque. Check the

tightness with a hand-torque wrench. If the fasten-

ers are too tight, reduce the impacting time. If they

are not tight enough, increase the impacting time.

Oil, dirt, rust or other matter on the threads or

under the head of the fastener aects the degree

of tightness.

The torque required to loosen a fastener averages

75% to 80% of the tightening torque, depending on

the condition of the contacting surfaces.

On light gasket jobs, run each fastener down to a

relatively light torque and use a hand torque wrench

for ﬁ nal tightening.

Push for

Forward

Push for

Reverse

Fig. 3

Fuel Gauge

To determine the amount of charge left in the bat-

tery, pull the trigger. The Fuel Gauge will light up

for 2-3 seconds.

To signal the end of charge, 1 light on the fuel gauge

will ﬂ ash for 2-3 seconds.

Using Control Switch

The control switch may be set to three positions:

forward, reverse and lock. Due to a lockout mecha-

nism, the control switch can only be adjusted when

the ON/OFF switch is not pressed. Always allow

the motor to come to a complete stop before using

the control switch.

PUSH TO CENTER TO LOCK

OPERATION

WARNING Always remove battery

pack before changing or removing accesso-

ries. Only use accessories speciﬁ cally recom-

mended for this tool. Others may be hazardous.

WARNING To reduce the risk of injury,

wear safety goggles or glasses with side shields.

For forward (clockwise) rotation, push the control

switch in the direction shown. Check the direction

of rotation before use.

For reverse (counterclockwise) rotation, push the

control switch in the direction shown. Check the

direction of rotation before use.

To lock the trigger, push the control switch to the

center position. The trigger will not work when the

control switch is in the locked position.

Always lock the trigger or remove the battery

pack before performing maintenance, changing

accessories, storing the tool and any time the tool

is not in use.

Starting, Stopping and Controlling Speed

These tools may be operated at any speed from

0 to full speed.

1. To start the tool, pull the trigger. NOTE: An LED

is turned on when the trigger is pulled.

2. To vary the driving speed, simply increase or

decrease pressure on the trigger. The further

the trigger is pulled, the greater the speed.

3. To stop the tool, release the trigger.

Impacting Techniques

The longer a bolt, screw, or nut is impacted, the

tighter it will become. To help prevent damaging the

fasteners or workpieces, avoid excessive impact-

ACCESSORIES

For a complete listing of accessories refer to your

MILWAUKEE Electric Tool catalog or go online

to www.milwaukeetool.com. To obtain a catalog,

contact your local distributor or service center.

WARNING Always remove battery pack

before changing or removing accessories.

Only use accessories speciﬁ cally recommend-

ed for this tool. Others may be hazardous.

Maintaining Tool

Keep your tool, battery pack and charger in good

repair by adopting a regular maintenance program.

After six months to one year, depending on use,

return the tool, battery pack and charger to A

MILWAUKEE service facility for:

• Lubrication

• Mechanical inspection and cleaning (gears, spin-

dles, bearings, housing, etc.)

• Electrical inspection (battery pack, charger, motor)

• Testing to assure proper mechanical and electrical

operation

If the tool does not start or operate at full power

with a fully charged battery pack, clean the contacts

on the battery pack. If the tool still does not work

properly, return the tool, charger and battery pack,

to a MILWAUKEE service facility for repairs.

MAINTENANCE

Cleaning

Clean dust and debris from charger and tool vents.

Keep tool handles clean, dry and free of oil or

grease. Use only mild soap and a damp cloth to

clean the tool, battery pack and charger since certain

cleaning agents and solvents are harmful to plastics

and other insulated parts. Some of these include

gasoline, turpentine, lacquer thinner, paint thinner,

chlorinated cleaning solvents, ammonia and house-

hold detergents containing ammonia. Never use

ﬂ ammable or combustible solvents around tools.

Repairs

For repairs, return the tool, battery pack and

charger to the nearest service center.

WARNING To reduce the risk of per-

sonal injury and damage, never immerse your

tool, battery pack or charger in liquid or allow

a liquid to ﬂ ow inside them.

WARNING To reduce the risk of injury,

always unplug the charger and remove the

battery pack from the charger or tool before

performing any maintenance. Never disas-

semble the tool, battery pack or charger.

Contact a MILWAUKEE service facility for

ALL repairs.

TECHTRONIC INDUSTRIES' warranty is for 5 year since the original purchase date.

This warranty card covers any defect in material and workmanship on this Power Tool.

To make this warranty valid, present this warranty card, sealed/stamped by the distributor or store where you pur-

chased the product, to the Authorized Service Center (ASC). Or, if this card has not been sealed/stamped, present the

original proof of purchase to the ASC.

Call toll-free 1 800 832 1949 to ﬁ nd the nearest ASC, for service, parts, accessories or components.

Procedure to make this warranty valid

Take the product to the ASC, along with the warranty card sealed/stamped by the distributor or store where you pur-

chased the product, and there any faulty piece or component will be replaced without cost for you. We will cover all

freight costs relative with this warranty process.

Exceptions

This warranty is not valid in the following situations:

a) When the product is used in a dierent manners from the end-user guide or instruction manual.

b) When the conditions of use are not normal.

c) When the product was modiﬁ ed or repaired by people not authorized by TECHTRONIC INDUSTRIES.

Note: If cord set is damaged, it should be replaced by an Authorized Service Center to avoid electric risks.

SERVICE AND ATTENTION CENTER

Av Presidente Mazarik 29 Piso 7, 11570 Chapultepec Morales

Miguel Hidalgo, Distrito Federal, Mexico

Ph. 52 55 4160-3547

IMPORTED AND COMMERCIALIZED BY:

TECHTRONIC INDUSTRIES MEXICO, .S.A. DE C.V.

Av Presidente Mazarik 29 Piso 7, 11570 Chapultepec Morales

Miguel Hidalgo, Distrito Federal, Mexico

LIMITED WARRANTY - USA AND CANADA

LIMITED WARRANTY - MEXICO, CENTRAL AMERICA AND CARIBBEAN

Model:

Date of Purchase:

Distributor or Store Stamp:

Every MILWAUKEE power tool (including cordless product – tool, battery pack(s) - see separate & distinct CORDLESS

BATTERY PACK LIMITED WARRANTY statements & battery charger and Work Lights*) is warranted to the original

purchaser only to be free from defects in material and workmanship. Subject to certain exceptions, MILWAUKEE will

repair or replace any part on an electric power tool which, after examination, is determined by MILWAUKEE to be defec-

tive in material or workmanship for a period of ﬁ ve (5) years* after the date of purchase unless otherwise noted. Return

of the power tool to a MILWAUKEE MILWAUKEE factory Service Center location or Authorized Service Station, freight

prepaid and insured, is required. A copy of the proof of purchase should be included with the return product. This warranty

does not apply to damage that MILWAUKEE determines to be from repairs made or attempted by anyone other than

MILWAUKEE authorized personnel, misuse, alterations, abuse, normal wear and tear, lack of maintenance, or accidents.

*The warranty period for, Job Site Radios, M12™ Power Port, M18™ Power Source, and Trade Titan™ Industrial Work

Carts is one (1) year from the date of purchase. The warranty period for a LED Work Light and LED Upgrade Bulb is

a limited LIFETIME warranty to the original purchaser only, if during normal use the LED bulb fails the Work Light or

Upgrade Bulb will be replaced free of charge.

*This warranty does not cover Air Nailers & Stapler, Airless Paint Sprayer, Cordless Battery Packs, Gasoline Driven

Portable Power Generators, Hand Tools, Hoist – Electric, Lever & Hand Chain, M12™ Heated Jackets, Reconditioned

product and Test & Measurement products. There are separate and distinct warranties available for these products.

Warranty Registration is not necessary to obtain the applicable warranty on a MILWAUKEE power tool product. The

manufacturing date of the product will be used to determine the warranty period if no proof of purchase is provided at

the time warranty service is requested.

ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT REMEDIES DESCRIBED HEREIN IS A CONDI-

TION OF THE CONTRACT FOR THE PURCHASE OF EVERY PRODUCT. IF YOU DO NOT AGREE TO MILWAUKEE

THIS CONDITION, YOU SHOULD NOT PURCHASE THE PRODUCT. IN NO EVENT SHALL BE LIABLE MILWAUKEE

FOR ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES, OR FOR ANY COSTS, ATTORNEY

FEES, EXPENSES, LOSSES OR DELAYS ALLEGED TO BE AS A CONSEQUENCE OF ANY DAMAGE TO, FAILURE OF,

OR DEFECT IN ANY PRODUCT INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOSS OF PROFITS. SOME

STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO

THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY IS EXCLUSIVE AND IN LIEU

OF ALL OTHER EXPRESS WARRANTIES, WRITTEN OR ORAL. TO THE EXTENT PERMITTED BY LAW, MILWAU-

KEE DISCLAIMS ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR PURPOSE; TO THE EXTENT SUCH DISCLAIMER IS

NOT PERMITTED BY LAW, SUCH IMPLIED WARRANTIES ARE LIMITED TO THE DURATION OF THE APPLICABLE

EXPRESS WARRANTY AS DESCRIBED ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN

IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU, THIS WARRANTY GIVES YOU

SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.

This warranty applies to product sold in the U.S.A. and Canada only.

Please consult the ‘Service Center Search’ in the Parts & Service section of MILWAUKEE’s website www.milwaukeetool.

com or call 1.800.SAWDUST (1.800.729.3878) to locate your nearest service facility for warranty and non-warranty

service on a Milwaukee electric power tool.

Especificaciones del producto

Marca:	Milwaukee
Categoría:	maquina de atornillar
Modelo:	2451-20

¿Necesitas ayuda?

Si necesitas ayuda con Milwaukee 2451-20 haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

maquina de atornillar Milwaukee Manuales

Milwaukee 2769-20 Manual de Usario

7 Octubre 2024

Milwaukee M12 Fuel 2454-22 Manual de Usario

4 Octubre 2024

Milwaukee 2455-20 Manual de Usario

27 Septiembre 2024

Milwaukee 48-22-2106 Manual de Usario

23 Septiembre 2024

Milwaukee 2868-20 Manual de Usario

20 Septiembre 2024

Milwaukee 2759-20 Manual de Usario

20 Septiembre 2024

Milwaukee M18 ONEFMTIW2FC12 Manual de Usario

19 Septiembre 2024

Milwaukee M18 FUEL 2953-20 Manual de Usario

17 Septiembre 2024

Milwaukee M18 Fuel One-Key 2857-22CT Manual de Usario

17 Septiembre 2024

Milwaukee M18 Fuel 2855-22 Manual de Usario

17 Septiembre 2024

maquina de atornillar Manuales

Últimos maquina de atornillar Manuales

Bosch GSB 12-2 Professional Manual de Usario

24 Octubre 2024

MSW -ACW700 Manual de Usario

20 Octubre 2024

Einhell CC-IW 450 Manual de Usario

17 Octubre 2024

Metabo SSW 650 Manual de Usario

17 Octubre 2024

Metabo SSW 18 LT Manual de Usario

15 Octubre 2024

Makita DHP448 Manual de Usario

12 Octubre 2024

Black And Decker HP9012 Manual de Usario

10 Octubre 2024

Bosch GSB 18V-65 Professional Manual de Usario

5 Octubre 2024

DeWalt DW132 Manual de Usario

5 Octubre 2024

Makita 6906J Manual de Usario

5 Octubre 2024