Milwaukee 2455-20 Manual de Usario
Milwaukee
maquina de atornillar
2455-20
Lee a continuación 📖 el manual en español para Milwaukee 2455-20 (11 páginas) en la categoría maquina de atornillar. Esta guía fue útil para 7 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/11
OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR
TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S
MANUAL.
AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE ET BIEN
COMPRENDRE LE MANUEL DE L'UTILISATEUR.
PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER Y ENTENDER EL
MANUAL DEL OPERADOR.
Cat. No.
No de cat.
2455-20
M12™ CORDLESS NO-HUB COUPLING DRILL DRIVER
PERCEUSE/TOURNEVIS À ACCOUPLEMENT SANS MOYEU M12™
TALADRO-DESTORNILLADOR SIN CUBO DE ACOPLAMIENTO DE M12™
2 3
• Hold power tool by insulated gripping sur-
faces, when performing an operation where the
fastener may contact hidden wiring. Fasteners
contacting a “live” wire may make exposed metal
parts of the power tool “live” and could give the
operator an electric shock.
• Wear ear protectors. Exposure to noise can
cause hearing loss.
• Keep hands away from all cutting edges and
moving parts.
• Maintain labels and nameplates. These carry
important information. If unreadable or missing,
contact a MILWAUKEE service facility for a free
replacement.
• WARNING: Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities contains chemicals known to cause
cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and cement and
other masonry products, and
• arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well venti-
lated area, and work with approved safety equip-
ment, such as those dust masks that are specially
designed to fi lter out microscopic particles.
Cat. No.
Volts
DC No Load RPM
Capacities
Drilling
in
Wood
Banding
Torque
2455-20 12 0-250 Banding
0-750 Drilling 1/2" 60 in.lbs.
80 in.lbs.
SPECIFICATIONS
FUNCTIONAL DESCRIPTION
PERSONAL SAFETY
GENERAL POWER TOOL SAFETY WARNINGS
WORK AREA SAFETY
ELECTRICAL SAFETY
• Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
• Do not operate power tools in explosive at-
mospheres, such as in the presence of fl am-
mable liquids, gases or dust. Power tools create
sparks which may ignite the dust or fumes.
• Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
• Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodifi ed plugs and matching outlets will
reduce risk of electric shock.
• Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet condi-
tions. Water entering a power tool will increase
the risk of electric shock.
• Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
• When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use
of a cord suitable for outdoor use reduces the risk
of electric shock.
• If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
attached to a rotating part of the power tool may
result in personal injury.
• Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewel-
lery or long hair can be caught in moving parts.
• If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
WARNING READ ALL SAFETY WARNINGS AND ALL INSTRUCTIONS.
Failure to follow the warnings and instructions may result in electric shock, fi re and/or
serious injury. Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
POWER TOOL USE AND CARE
• Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
• Do not use the power tool if the switch does not
turn it on and o. Any power tool that cannot be
controlled with the switch is dangerous and must
be repaired.
• Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
• Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
• Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits
etc., in accordance with these instructions,
taking into account the working conditions and
the work to be performed. Use of the power tool
for operations dierent from those intended could
result in a hazardous situation.
• Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the infl uence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
• Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
• Prevent unintentional starting. Ensure the
switch is in the o-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
your fi nger on the switch or energising power tools
that have the switch on invites accidents.
• Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
• Recharge only with the charger specifi ed by
the manufacturer. A charger that is suitable for
one type of battery pack may create a risk of fi re
when used with another battery pack.
• Use power tools only with specifi cally desig-
nated battery packs. Use of any other battery
packs may create a risk of injury and fi re.
BATTERY TOOL USE AND CARE
SPECIFIC SAFETY RULES
• When battery pack is not in use, keep it away
from other metal objects like paper clips,
coins, keys, nails, screws, or other small metal
objects that can make a connection from one
terminal to another. Shorting the battery termi-
nals together may cause burns or a fi re.
• Under abusive conditions, liquid may be eject-
ed from the battery; avoid contact. If contact
accidentally occurs, fl ush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation
or burns.
SERVICE
• Have your power tool serviced by a qualifi ed
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
SYMBOLOGY
Volts
Direct Current
No Load Revolutions per
Minute (RPM)
Underwriters Laboratories, Inc.
United States and Canada
1. Bit holder collar
2. Mode selector collar
3. Torque LED
4. Fuel gauge
5. Control switch
6. Trigger
7. Worklight LED
1
2
6
7
3
4
5
4 5
Recalibration:
To maintain high-precision torque, the tool will oc-
casionally need to be recalibrated. To signify that
the tool may be out of an acceptable tolerance
torque range, theTorque LED will fl ash after the
trigger is released. The tool can continue to be used
for jobs not requiring accurate torque, but should
be returned to a MILWAUKEE service facility for
recalibration before using for precision torque work.
Please send the M12™ No–Hub Coupling Drill
Driver needing service of the torque mechanism
(or if tool has reached its 25,000 cycles) to:
Milwaukee Electric Tool Corporation
13135 West Lisbon Road
Brookfi eld, Wisconsin 53005
Attention: After–Sales Service
to calibrate the M12™ No–Hub Coupling Drill Driver
to manufacturer’s specifi cation of 60/80 in–lbs,
using calibrated test equipment traceable to the
National Institute of Standards and Technology
Standards. Product will be returned with manu-
facturer’s statement of calibration. There is an ad-
ditional charge to obtain a separate NIST - National
Institute of Standards and Technology Standards
“Certifi cate of Calibration”.
Using the Control Switch
The control switch may be set to
three positions: forward, reverse
and lock. Due to a lockout mecha-
nism, the control switch can only be
adjusted when the ON/OFF switch
is not pressed. Always allow the
motor to come to a complete stop
before using the control switch.
For forward (clockwise) rotation,
push in the control switch from the
right side of the tool. Check the
direction of rotation before use.
For (counterclockwise) reverse
rotation, push in the control switch
from the left side of the tool. Check
direction of rotation before use.
To lock the trigger, push the con-
trol switch to the center position.
The trigger will not work while
the control switch is in the center
locked position. Always lock the
trigger or remove the battery pack
before performing maintenance,
changing accessories, storing the tool and any time
the tool is not in use.
Battery Pack Protection
To protect the battery from damage and extend
its life, the tool’s intelligent circuit monitors current
draw, temperature, and voltage drops.
In extremely high torque, binding, stalling, and short
circuit situations that cause high current draw, the
fuel gauge will fl ash, and the tool will turn OFF. To
reset, release the trigger.
Under extreme circumstances, the internal tem-
perature of the battery could become too high.
If this happens, the fuel gauge will fl ash and the
battery pack will shut o. Let the battery pack cool
and then continue work.
APPLICATIONS
WARNING To reduce the risk of elec-
tric shock, check work area for hidden pipes
and wires before drilling or driving screws.
Forward -
Push from RIGHT
Lock -
Push to CENTER
Reverse -
Push from LEFT
This tool provides a quick, convenient means of drill-
ing small holes and installing and removing bands.
Drilling in Wood, Composition Materials and
Plastic
Always use sharp bits. When using twist drill bits,
pull the bit out of the hole frequently to clear chips
from the bit fl utes. To reduce the chance of splinter-
ing, back work with a piece of scrap wood.
During binding or high torque drilling applications,
the tool may shut down. To reset, release the trigger.
Tightening/Removing Bands
Adjust the clutch to the proper setting as indicated
by the band manufacterer. Place the proper size
socket into the tool. Fit the socket over the band fas-
tener and pull the trigger. When the proper torque
is reqched, the clutch will slip, the tool will stop,
and the torque LED will light. Release the trigger.
When removing bands, it may be necessary to
slightly loosen the band fastener by hand before
using the tool's reverse. Fit the socket over the band
fastener. Manually rotate the tool counterclockwise
to release the torque on the fastener. Put the tool into
reverse and pull the trigger fo fully release the band.
Maintaining Tool
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance program.
After six months to one year, depending on use,
return the tool, battery pack and charger to A
MILWAUKEE service facility for:
• Lubrication
• Mechanical inspection and cleaning (gears, spin-
dles, bearings, housing, etc.)
• Electrical inspection (battery pack, charger, motor)
• Testing to assure proper mechanical and electrical
operation
If the tool does not start or operate at full power
with a fully charged battery pack, clean the contacts
on the battery pack. If the tool still does not work
properly, return the tool, charger and battery pack,
to a MILWAUKEE service facility for repairs.
MAINTENANCE
WARNING To reduce the risk of per-
sonal injury and damage, never immerse your
tool, battery pack or charger in liquid or allow
a liquid to fl ow inside them.
WARNING To reduce the risk of injury,
always unplug the charger and remove the
battery pack from the charger or tool before
performing any maintenance. Never disas-
semble the tool, battery pack or charger.
Contact a MILWAUKEE service facility for
ALL repairs.
WARNING Recharge only with the
charger specifi ed for the battery. For specifi c
charging instructions, read the operator’s
manual supplied with your charger and battery.
Inserting/Removing the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
To insert the battery, slide the pack into the body of
the tool. Make sure it latches securely into place.
OPERATION
WARNING Always remove battery
pack before changing or removing accesso-
ries. Only use accessories specifi cally recom-
mended for this tool. Others may be hazardous.
WARNING To reduce the risk of injury,
wear safety goggles or glasses with side shields.
Fuel Gauge
To determine the amount of charge left in the bat-
tery, pull the trigger. The Fuel Gauge will light up for
2-3 seconds. To signal the end of charge, 1 light on
the fuel gauge will fl ash for 2-3 seconds.
Installing Bits and Sockets
Always remove the battery before inserting or
removing accessories. Select the proper style and
size accessories for the job. This driver is intended
for use with drill and driver bits with a 1/4" hex shank
and ball detent recess.
1. To install the accessory, pull out the collar and
insert the accessory. Release the collar.
2. To remove the accessory, pull out the collar and
remove the accessory.
Setting the Mode
The mode selector collar can be
set to 60 in. lbs, 80 in. lbs, or Drill.
When properly adjusted, the clutch
will slip at the set torque to prevent
over-tightening and possibly damag-
ing the bands.
To tighten bands, turn the mode
selector collar so the arrow lines up
with either 60 or 80, as indicated by
the band manufacterer.
To drill, turn the mode selector collar
so the arrow lines up with .
Torque LED
When the specifi ed torque is reached
(60/80 in.lbs), the Torque LED on the
back of the tool will light.
60
Tightening
80
Tightening
80
Drilling
ASSEMBLY
ACCESSORIES
For a complete listing of accessories refer to your
MILWAUKEE Electric Tool catalog or go online
to www.milwaukeetool.com. To obtain a catalog,
contact your local distributor or service center.
WARNING Always remove battery pack
before changing or removing accessories.
Only use accessories specifi cally recommend-
ed for this tool. Others may be hazardous.
Cleaning
Clean dust and debris from charger and tool vents.
Keep tool handles clean, dry and free of oil or
grease. Use only mild soap and a damp cloth to
clean the tool, battery pack and charger since certain
cleaning agents and solvents are harmful to plastics
and other insulated parts. Some of these include
gasoline, turpentine, lacquer thinner, paint thinner,
chlorinated cleaning solvents, ammonia and house-
hold detergents containing ammonia. Never use
fl ammable or combustible solvents around tools.
Repairs
For repairs, return the tool, battery pack and
charger to the nearest service center.
Especificaciones del producto
| Marca: | Milwaukee |
| Categoría: | maquina de atornillar |
| Modelo: | 2455-20 |
¿Necesitas ayuda?
Si necesitas ayuda con Milwaukee 2455-20 haz una pregunta a continuación y otros usuarios te responderán
maquina de atornillar Milwaukee Manuales
7 Octubre 2024
4 Octubre 2024
27 Septiembre 2024
23 Septiembre 2024
20 Septiembre 2024
20 Septiembre 2024
19 Septiembre 2024
17 Septiembre 2024
17 Septiembre 2024
17 Septiembre 2024
maquina de atornillar Manuales
- maquina de atornillar Bosch
- maquina de atornillar AEG
- maquina de atornillar DeWalt
- maquina de atornillar Silverline
- maquina de atornillar Ferm
- maquina de atornillar Gude
- maquina de atornillar Omega
- maquina de atornillar Makita
- maquina de atornillar Hitachi
- maquina de atornillar Black And Decker
- maquina de atornillar Vonroc
- maquina de atornillar Stanley
- maquina de atornillar Skil
- maquina de atornillar Yato
- maquina de atornillar Hilti
- maquina de atornillar Ryobi
- maquina de atornillar Festool
- maquina de atornillar Metabo
- maquina de atornillar Parkside
- maquina de atornillar Worx
- maquina de atornillar Meec Tools
- maquina de atornillar Hikoki
- maquina de atornillar Dremel
- maquina de atornillar Tacklife
- maquina de atornillar Hazet
- maquina de atornillar Einhell
- maquina de atornillar Maktec
- maquina de atornillar Craftsman
- maquina de atornillar Powerplus
- maquina de atornillar Cotech
- maquina de atornillar Genesis
- maquina de atornillar Beta
- maquina de atornillar Kraftwerk
- maquina de atornillar Kress
- maquina de atornillar Fieldmann
- maquina de atornillar Truper
- maquina de atornillar Cocraft
- maquina de atornillar Meister Craft
- maquina de atornillar Toolcraft
- maquina de atornillar Fein
- maquina de atornillar Park Tool
- maquina de atornillar Elu
- maquina de atornillar Goon
- maquina de atornillar Sthor
- maquina de atornillar Wiha
- maquina de atornillar SW-Stahl
- maquina de atornillar Cleco
- maquina de atornillar MSW
- maquina de atornillar Einhell Bavaria
- maquina de atornillar Wera
- maquina de atornillar Rodcraft
- maquina de atornillar Ingersoll Rand
- maquina de atornillar Bavaria By Einhell
- maquina de atornillar Chicago Pneumatic
- maquina de atornillar Facom
- maquina de atornillar TAURUS Titanium
Últimos maquina de atornillar Manuales
24 Octubre 2024
20 Octubre 2024
17 Octubre 2024
17 Octubre 2024
15 Octubre 2024
12 Octubre 2024
10 Octubre 2024
5 Octubre 2024
5 Octubre 2024
5 Octubre 2024