Milwaukee M12 Fuel 2454-22 Manual de Usario
Milwaukee
maquina de atornillar
M12 Fuel 2454-22
Lee a continuación 📖 el manual en español para Milwaukee M12 Fuel 2454-22 (16 páginas) en la categoría maquina de atornillar. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/16
Cat. No. / No de cat.
2452-20, 2453-20, 2454-20
OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR
WARNING To reduce the risk of injury, user must read and understand operator's manual.
AVERTISSEMENT An de réduire le risque de blessures, l'utilisateur doit lire et bien
comprendre le manuel.
ADVERTENCIA Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual.
M12 FUEL™ 1/4" HEX IMPACT DRIVER, 1/4" IMPACT WRENCH &
3/8" IMPACT WRENCH
TOURNEVIS À PERCUSSION HEXAGONAL 6 mm (1/4"), CLÉS
À CHOCS DE 1/4" & CLÉS À CHOCS DE 3/8" DE M12 FUEL™
DESTORNILLADOR HEXAGONAL DE IMPACTO DE 6 mm (1/4"),
LLAVES DE IMPACTO DE 1/4" & LLAVES DE IMPACTO DE 3/8"
DE M12 FUEL™
2
GENERAL POWER TOOL
SAFETY WARNINGS
WARNING
Read all safety warnings, instruc-
tions, illustrations and specica-
tions provided with this power tool. Failure to
follow all instructions listed below may result in
electric shock, re and/or serious injury. Save all
warnings and instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-oper-
ated (cordless) power tool.
WORK AREA SAFETY
• Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
• Do not operate power tools in explosive atmo-
spheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
• Keep children and bystanders away while operat-
ing a power tool. Distractions can cause you to lose
control.
ELECTRICAL SAFETY
• Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodied plugs and matching outlets will
reduce risk of electric shock.
• Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet condi-
tions. Water entering a power tool will increase the
risk of electric shock.
• Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
• When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
• If operating a power tool in a damp location is
unavoidable, use a ground fault circuit interrupter
(GFCI) protected supply. Use of an GFCI reduces
the risk of electric shock.
PERSONAL SAFETY
• Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the inuence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
• Use personal protective equipment. Always wear
eye protection. Protective equipment such as a dust
mask, non-skid safety shoes, hard hat or hearing
protection used for appropriate conditions will reduce
personal injuries.
• Prevent unintentional starting. Ensure the switch
is in the o-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your nger on the
switch or energizing power tools that have the switch
on invites accidents.
• Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result
in personal injury.
• Do not overreach. Keep proper footing and bal-
ance at all times. This enables better control of the
power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or
jewelry. Keep your hair and clothing away from
moving parts. Loose clothes, jewelry or long hair
can be caught in moving parts.
• If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used. Use of dust
collection can reduce dust-related hazards.
• Do not let familiarity gained from frequent use of
tools allow you to become complacent and ignore
tool safety principles. A careless action can cause
severe injury within a fraction of a second.
POWER TOOL USE AND CARE
• Do not force the power tool. Use the correct
power tool for your application. The correct power
tool will do the job better and safer at the rate for
which it was designed.
• Do not use the power tool if the switch does not
turn it on and o. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
• Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from
the power tool before making any adjustments,
changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
• Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands
of untrained users.
• Maintain power tools and accessories. Check for
misalignment or binding of moving parts, break-
age of parts and any other condition that may
aect the power tool’s operation. If damaged,
have the power tool repaired before use. Many ac-
cidents are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
dierent from those intended could result in a hazard-
ous situation.
• Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
3
BATTERY TOOL USE AND CARE
• Recharge only with the charger specied by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of re when used
with another battery pack.
• Use power tools only with specically designated
battery packs. Use of any other battery packs may
create a risk of injury and re.
• When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal to
another. Shorting the battery terminals together may
cause burns or a re.
• Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact ac-
cidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation
or burns.
• Do not use a battery pack or tool that is dam-
aged or modied. Damaged or modied batteries
may exhibit unpredictable behavior resulting in re,
explosion or risk of injury.
• Do not expose a battery pack or tool to re or
excessive temperature. Exposure to re or tem-
perature above 265°F (130°C) may cause explosion.
• Follow all charging instructions and do not charge
the battery pack or tool outside the temperature
range specied in the instructions. Charging
improperly or at temperatures outside the specied
range may damage the battery and increase the risk
of re.
SERVICE
• Have your power tool serviced by a qualied
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
• Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
SPECIFIC SAFETY RULES FOR
IMPACT DRIVER/IMPACT WRENCH
• Hold power tool by insulated gripping surfaces,
when performing an operation where the fastener
may contact hidden wiring. Fasteners contacting a
“live” wire may make exposed metal parts of the power
tool “live” and could give the operator an electric shock.
• Wear ear protectors when impact drilling. Expo-
sure to noise can cause hearing loss.
• Use only sockets and other accessories speci-
cally designed for use on impact wrenches and
drivers. Other sockets and accessories might shatter
or break causing injury.
•
WARNING
To reduce the risk of injury, when
working in dusty situations, wear
appropriate respiratory protection or use an
OSHA compliant dust extraction solution.
• Always use common sense and be cautious when
using tools. It is not possible to anticipate every
situation that could result in a dangerous outcome.
Do not use this tool if you do not understand these
operating instructions or you feel the work is beyond
your capability; contact Milwaukee Tool or a trained
professional for additional information or training.
• Maintain labels and nameplates. These carry im-
portant information. If unreadable or missing, contact
a MILWAUKEE service facility for a free replacement.
•
WARNING
Some dust created by power sanding,
sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to
lter out microscopic particles.
SYMBOLOGY
Volts
Direct Current
No Load Revolutions per Minute (RPM)
Impacts per Minute Under Load (IPM)
C US
UL Listing for Canada and U.S.
SPECIFICATIONS
Volts .............................................................. 12 DC
Battery Type .................................................M12™
Charger Type ................................................M12™
Recommended Ambient
Operating Temperature ......................0°F to 125°F
Cat. No. 2452-20 .....................................................
RPM ..... ...............................Mode 1 Speed 0-1200
Mode 2 ...............................Speed 0-2650
IPM ...... .............................Mode 1 Impacts 0-3000
Mode 2 .............................Impacts 0-4000
Cat. No. 2453-20 .....................................................
RPM .... ...............................Mode 1 Speed 0-1200
Mode 2 ...............................Speed 0-2650
IPM ...... .............................Mode 1 Impacts 0-2700
Mode 2 .............................Impacts 0-3550
Cat. No. 2454-20 .....................................................
RPM ...... ..............................Mode 1 Speed 0-1200
Mode 2 .............................. Speed 0-2650
IPM ....... ............................Mode 1 Impacts 0-2650
Mode 2 ............................Impacts 0-3500
Especificaciones del producto
| Marca: | Milwaukee |
| Categoría: | maquina de atornillar |
| Modelo: | M12 Fuel 2454-22 |
¿Necesitas ayuda?
Si necesitas ayuda con Milwaukee M12 Fuel 2454-22 haz una pregunta a continuación y otros usuarios te responderán
maquina de atornillar Milwaukee Manuales
7 Octubre 2024
4 Octubre 2024
27 Septiembre 2024
23 Septiembre 2024
20 Septiembre 2024
20 Septiembre 2024
19 Septiembre 2024
17 Septiembre 2024
17 Septiembre 2024
17 Septiembre 2024
maquina de atornillar Manuales
- maquina de atornillar Bosch
- maquina de atornillar AEG
- maquina de atornillar DeWalt
- maquina de atornillar Silverline
- maquina de atornillar Ferm
- maquina de atornillar Gude
- maquina de atornillar Omega
- maquina de atornillar Makita
- maquina de atornillar Hitachi
- maquina de atornillar Black And Decker
- maquina de atornillar Vonroc
- maquina de atornillar Stanley
- maquina de atornillar Skil
- maquina de atornillar Yato
- maquina de atornillar Hilti
- maquina de atornillar Ryobi
- maquina de atornillar Festool
- maquina de atornillar Metabo
- maquina de atornillar Parkside
- maquina de atornillar Worx
- maquina de atornillar Meec Tools
- maquina de atornillar Hikoki
- maquina de atornillar Dremel
- maquina de atornillar Tacklife
- maquina de atornillar Hazet
- maquina de atornillar Einhell
- maquina de atornillar Maktec
- maquina de atornillar Craftsman
- maquina de atornillar Power Craft
- maquina de atornillar Powerplus
- maquina de atornillar Cotech
- maquina de atornillar Genesis
- maquina de atornillar Beta
- maquina de atornillar Kraftwerk
- maquina de atornillar Kress
- maquina de atornillar Fieldmann
- maquina de atornillar Truper
- maquina de atornillar Cocraft
- maquina de atornillar Meister Craft
- maquina de atornillar Toolcraft
- maquina de atornillar Fein
- maquina de atornillar Park Tool
- maquina de atornillar Elu
- maquina de atornillar Goon
- maquina de atornillar Sthor
- maquina de atornillar Wiha
- maquina de atornillar SW-Stahl
- maquina de atornillar Cleco
- maquina de atornillar MSW
- maquina de atornillar Weidmüller
- maquina de atornillar Einhell Bavaria
- maquina de atornillar Wera
- maquina de atornillar Rodcraft
- maquina de atornillar Ingersoll Rand
- maquina de atornillar Bavaria By Einhell
- maquina de atornillar Chicago Pneumatic
- maquina de atornillar Facom
- maquina de atornillar TAURUS Titanium
Últimos maquina de atornillar Manuales
24 Octubre 2024
20 Octubre 2024
17 Octubre 2024
17 Octubre 2024
15 Octubre 2024
12 Octubre 2024
10 Octubre 2024
5 Octubre 2024
5 Octubre 2024
5 Octubre 2024