Milwaukee 2556-20 Manual de Usario
Milwaukee
maquina de atornillar
2556-20
Lee a continuación 📖 el manual en español para Milwaukee 2556-20 (12 páginas) en la categoría maquina de atornillar. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/12
Cat. No. / No de cat.
2556-20, 2557-20, 2558-20
M12 FUEL™ RATCHETS
CLIQUETS FUEL™ M12
TRINQUETES FUEL™ M12
OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR
WARNING To reduce the risk of injury, user must read and understand operator's manual.
AVERTISSEMENT An de réduire le risque de blessures, l'utilisateur doit lire et bien
comprendre le manuel.
ADVERTENCIA Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual.
2
GENERAL POWER TOOL
SAFETY WARNINGS
WARNING
Read all safety warnings, instruc-
tions, illustrations and specica-
tions provided with this power tool. Failure to
follow all instructions listed below may result in
electric shock, re and/or serious injury. Save all
warnings and instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-oper-
ated (cordless) power tool.
WORK AREA SAFETY
• Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
• Do not operate power tools in explosive atmo-
spheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
• Keep children and bystanders away while operat-
ing a power tool. Distractions can cause you to lose
control.
ELECTRICAL SAFETY
• Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodied
plugs and matching outlets will reduce risk of electric
shock.
• Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
• Do not abuse the cord. Never use the cord for car-
rying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk
of electric shock.
• When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
• If operating a power tool in a damp location is
unavoidable, use a ground fault circuit interrupter
(GFCI) protected supply. Use of an GFCI reduces
the risk of electric shock.
PERSONAL SAFETY
• Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the inuence of drugs, alcohol or medication. A
moment of inattention while operating power tools may
result in serious personal injury.
• Use personal protective equipment. Always wear
eye protection. Protective equipment such as a dust
mask, non-skid safety shoes, hard hat or hearing
protection used for appropriate conditions will reduce
personal injuries.
• Prevent unintentional starting. Ensure the switch
is in the o-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your nger on the
switch or energizing power tools that have the switch
on invites accidents.
• Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in personal
injury.
• Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
tool in unexpected situations.
• Dress properly. Do not wear loose clothing or
jewelry. Keep your hair and clothing away from
moving parts. Loose clothes, jewelry or long hair can
be caught in moving parts.
• If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
• Do not let familiarity gained from frequent use of
tools allow you to become complacent and ignore
tool safety principles. A careless action can cause
severe injury within a fraction of a second.
POWER TOOL USE AND CARE
• Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the
job better and safer at the rate for which it was designed.
• Do not use the power tool if the switch does not turn
it on and o. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
• Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from
the power tool before making any adjustments,
changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting
the power tool accidentally.
• Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool
or these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
• Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage
of parts and any other condition that may aect the
power tool’s operation. If damaged, have the power
tool repaired before use. Many accidents are caused
by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations dierent
from those intended could result in a hazardous situation.
• Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
BATTERY TOOL USE AND CARE
• Recharge only with the charger specied by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of re when used with
another battery pack.
• Use power tools only with specically designated
battery packs. Use of any other battery packs may
create a risk of injury and re.
• When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause
burns or a re.
• Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
occurs, ush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from
the battery may cause irritation or burns.
3
• Do not use a battery pack or tool that is damaged or
modied. Damaged or modied batteries may exhibit
unpredictable behavior resulting in re, explosion or
risk of injury.
• Do not expose a battery pack or tool to re or
excessive temperature. Exposure to re or temperature
above 265°F (130°C) may cause explosion.
• Follow all charging instructions and do not charge
the battery pack or tool outside the temperature
range specied in the instructions. Charging im-
properly or at temperatures outside the specied range
may damage the battery and increase the risk of re.
SERVICE
• Have your power tool serviced by a qualied repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
• Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
SPECIFIC SAFETY RULES FOR
RATCHETS
• Hold the power tool by insulated gripping surfaces,
when performing an operation where the fastener
may contact hidden wiring. Fasteners contacting a
“live” wire may make exposed metal parts of the power
tool “live” and could give the operator an electric shock.
• Always use common sense and be cautious when
using tools. It is not possible to anticipate every
situation that could result in a dangerous outcome.
Do not use this tool if you do not understand these
operating instructions or you feel the work is beyond
your capability; contact Milwaukee Tool or a trained
professional for additional information or training.
• Maintain labels and nameplates. These carry
important information. If unreadable or missing, contact
a MILWAUKEE service facility for a free replacement.
•
WARNING
Some dust created by power sanding,
sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to
lter out microscopic particles.
SPECIFICATIONS
Volts 12 DC..............................................................
Battery Type .................................................M12™
Charger Type M12™................................................
Recommended Ambient
Operating Temperature ......................0°F to 125°F
Cat. No. 2556-20 .....................................................
RPM ............................................................... 0-250
Torque Range ..........................................0-40 ft-lbs
Square Drive Anvil ............................................ 1/4"
Cat. No. 2557-20 .....................................................
RPM ............................................................... 0-200
Torque Range ..........................................0-55 ft-lbs
Square Drive Anvil ............................................ 3/8"
Cat. No. 2558-20 .....................................................
RPM ............................................................... 0-175
Torque Range ..........................................0-60 ft-lbs
Square Drive Anvil ............................................ 1/2"
SYMBOLOGY
Volts
Direct Current
No Load Revolutions per Minute (RPM)
Lock Switch
C US
UL Listing for Canada and U.S.
FUNCTIONAL DESCRIPTION
1. Paddle switch
2. Lock switch
3. LED
4. 1/4" square drive anvil
5. Forward/Reverse toggle
6. Fuel gauge
7. Handle
8. 3/8" square drive anvil
9. 1/2" square drive anvil
No de Cat. 2558-20
9
No de Cat. 2557-20
8
5
4
6
21
7
No de Cat. 2556-20
3
ASSEMBLY
WARNING
Recharge only with the charger
specied for the battery. For spe-
cic charging instructions, read the operator’s
manual supplied with your charger and battery.
Removing/Inserting the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
WARNING
Always remove battery pack before
changing or removing accessories.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
WARNING
Only use accessories specically
recommended for this tool. Others
may be hazardous.
Use only sockets and other accessories spe-
cically designed for use on impact tools. Other
sockets and accessories might shatter or break
causing injury.
Attaching and Removing Accessories
These tools are intended only for use with accesso-
ries designed for impact tools. Other sockets could
shatter or break, causing injury.
1. Use only appropriate Square Drive Sockets.
2. To attach a socket or other accessory, align the
accessory with the drive anvil and push it rmly
onto the tool.
3. To remove the accessory, pull the accessory o
the drive anvil.
Especificaciones del producto
| Marca: | Milwaukee |
| Categoría: | maquina de atornillar |
| Modelo: | 2556-20 |
¿Necesitas ayuda?
Si necesitas ayuda con Milwaukee 2556-20 haz una pregunta a continuación y otros usuarios te responderán
maquina de atornillar Milwaukee Manuales
7 Octubre 2024
4 Octubre 2024
27 Septiembre 2024
23 Septiembre 2024
20 Septiembre 2024
20 Septiembre 2024
19 Septiembre 2024
17 Septiembre 2024
17 Septiembre 2024
17 Septiembre 2024
maquina de atornillar Manuales
- maquina de atornillar Bosch
- maquina de atornillar AEG
- maquina de atornillar DeWalt
- maquina de atornillar Silverline
- maquina de atornillar Ferm
- maquina de atornillar Gude
- maquina de atornillar Omega
- maquina de atornillar Makita
- maquina de atornillar Hitachi
- maquina de atornillar Black And Decker
- maquina de atornillar Vonroc
- maquina de atornillar Stanley
- maquina de atornillar Skil
- maquina de atornillar Yato
- maquina de atornillar Hilti
- maquina de atornillar Ryobi
- maquina de atornillar Festool
- maquina de atornillar Metabo
- maquina de atornillar Parkside
- maquina de atornillar Worx
- maquina de atornillar Meec Tools
- maquina de atornillar Hikoki
- maquina de atornillar Dremel
- maquina de atornillar Tacklife
- maquina de atornillar Hazet
- maquina de atornillar Einhell
- maquina de atornillar Maktec
- maquina de atornillar Craftsman
- maquina de atornillar Powerplus
- maquina de atornillar Cotech
- maquina de atornillar Genesis
- maquina de atornillar Beta
- maquina de atornillar Kraftwerk
- maquina de atornillar Kress
- maquina de atornillar Fieldmann
- maquina de atornillar Truper
- maquina de atornillar Cocraft
- maquina de atornillar Meister Craft
- maquina de atornillar Toolcraft
- maquina de atornillar Fein
- maquina de atornillar Park Tool
- maquina de atornillar Elu
- maquina de atornillar Goon
- maquina de atornillar Sthor
- maquina de atornillar Wiha
- maquina de atornillar SW-Stahl
- maquina de atornillar Cleco
- maquina de atornillar MSW
- maquina de atornillar Einhell Bavaria
- maquina de atornillar Wera
- maquina de atornillar Rodcraft
- maquina de atornillar Ingersoll Rand
- maquina de atornillar Bavaria By Einhell
- maquina de atornillar Chicago Pneumatic
- maquina de atornillar Facom
- maquina de atornillar TAURUS Titanium
Últimos maquina de atornillar Manuales
24 Octubre 2024
20 Octubre 2024
17 Octubre 2024
17 Octubre 2024
15 Octubre 2024
12 Octubre 2024
10 Octubre 2024
5 Octubre 2024
5 Octubre 2024
5 Octubre 2024