Monoprice Joule 3D Printer DIY Assembly Kit Manual de Usario
Monoprice
Impresora 3D
Joule 3D Printer DIY Assembly Kit
Lee a continuación 📖 el manual en español para Monoprice Joule 3D Printer DIY Assembly Kit (45 páginas) en la categoría Impresora 3D. Esta guía fue útil para 7 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/45
Joule 3D Print
Joule 3D Print
Joule 3D Print
Joule 3D PrintJoule 3D Printer DIY Assembly Kit
er DIY Assembly Kit
er DIY Assembly Kit
er DIY Assembly Kit er DIY Assembly Kit
P/N 43363
User's Manual
User's Manual
User's Manual
User's Manual User's Manual
2
SAFETY WARNINGS
SAFETY WARNINGS
SAFETY WARNINGS
SAFETY WARNINGSSAFETY WARNINGS AND GUIDELINES
AND GUIDELINES
AND GUIDELINES
AND GUIDELINES AND GUIDELINES
Please read this entire manual before using this device, paying extra attention to these safety warnings and guidelines. Please keep this
manual in a safe place for future reference.
• This device is intended for indoor use only.
• Do not expose this device to water or moisture of any kind. Do not place drinks or other containers with moisture on or near the
device. If moisture does get in or on the device, immediately remove it from its power source and allow it to fully dry before
reapplying power.
• Do not touch the device, the power cord, or any other connected cables with wet hands.
• Do not install this device on an unstable surface where it could fall and cause either personal injury or damage to the device
and/or other equipment.
• Do not expose this device to excessive vibration, extreme force, shock, or fluctuations in temperature or humidity.
• Do not expose this device to excessively high temperatures. Do not place it in, on, or near a heat source, such as a fireplace,
stove, radiator, etc. Do not leave it in direct sunlight.
• Do not place or install this device in an area where it can be exposed to excessive amounts of dust, humidity, oil, smoke, or
combustible vapors.
• Use only in a well-ventilated area. Do not use in close, confined spaces.
• Prior to operation, check the unit and power cord for physical damage. Do not use if physical damage has occurred.
• Before plugging the unit into a power outlet, ensure that the outlet provides the same type and level of power required by the
device.
3
• This device uses a grounded power cord and requires a ground connection for safe operation. Ensure that the power source has
a proper ground connection. Do not modify the plug or use a "cheater" plug to bypass the ground connection.
• Unplug this device from the power source when not in use.
• Take care to prevent damage to the power cord. Do not allow it to become crimped, pinched, walked on, or become tangled
with other cords. Ensure that the power cord does not present a tripping hazard.
• Never unplug the unit by pulling on the power cord. Always grasp the connector head or adapter body.
• Clean using a soft, dry cloth only. Do not use chemical cleaners, solvents, or detergents. For stubborn deposits, moisten the cloth
with warm water.
• This device has no user serviceable parts. Do not attempt to open, service, or modify this device.
• Take care to avoid touching hot parts, including heat blocks, extruder nozzle, extruded filament, and the heated build plate.
• Do not wear gloves when operating or repairing to avoid entanglement.
• Keep the printer and all accessories out of reach of children.
• Do not reach inside the printer during operation.
• Always allow the printer and extruded filament to cool before reaching inside.
• Ensure that the printer is turned off and unplugged from its power source before making repairs or performing service.
Especificaciones del producto
| Marca: | Monoprice |
| Categoría: | Impresora 3D |
| Modelo: | Joule 3D Printer DIY Assembly Kit |
¿Necesitas ayuda?
Si necesitas ayuda con Monoprice Joule 3D Printer DIY Assembly Kit haz una pregunta a continuación y otros usuarios te responderán
Impresora 3D Monoprice Manuales
30 Agosto 2024
Monoprice Joule 3D Printer DIY Assembly Kit Manual de Usario
30 Agosto 2024Impresora 3D Manuales
- Impresora 3D Anker
- Impresora 3D Kodak
- Impresora 3D BQ
- Impresora 3D Flashforge
- Impresora 3D XYZprinting
- Impresora 3D MakerBot
- Impresora 3D Leap Frog
- Impresora 3D Anycubic
- Impresora 3D Easy Threed
- Impresora 3D LulzBot
- Impresora 3D Wasp
- Impresora 3D 3D Systems
- Impresora 3D Creality
- Impresora 3D Raise3D
- Impresora 3D Craftbot
Últimos Impresora 3D Manuales
27 Septiembre 2024
17 Septiembre 2024
17 Septiembre 2024
16 Septiembre 2024
16 Septiembre 2024
16 Septiembre 2024
14 Septiembre 2024
14 Septiembre 2024
14 Septiembre 2024
14 Septiembre 2024