Netgear ProSafe WAC740 Manual de Usario

Netgear punto de acceso ProSafe WAC740

Lee a continuación 📖 el manual en español para Netgear ProSafe WAC740 (2 páginas) en la categoría punto de acceso. Esta guía fue útil para 8 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

Installation

NETGEAR ProSAFE Dual Band Wireless AC

Access Point

WAC740

Set Up the Access Point

Before mounting the access point in a high location, ﬁrst set up and test the

access point to verify WiFi network connectivity.

IMPORTANT: You can deploy the WAC740 access point only in a WiFi

network that is managed by a ProSAFE wireless controller.

¾To cable the access point:

1. Connect an Ethernet cable from LAN port 1 on the access point to a

LAN port on a PoE+ switch, that is, an 802.3at-compatible switch.

2. Connect an Ethernet cable from the PoE+ switch to an Ethernet port on

the computer.

3. Check the LEDs to verify that the access point is set up correctly.

LED Description

Power LED

•O. Power is o.

•Solid green. Power is on.

•Alternating green and amber. The access point is receiving insucient

PoE power.

•Solid amber, then blinking amber. A self-test is running or ﬁrmware is

being loaded. During startup, the Power LED ﬁrst lights solid amber, then

goes o, and then blinks amber before turning solid green aer about

one minute. If aer two minutes the Power LED remains solid amber or

continues to blink amber, it indicates a system fault.

Activity LED

•O. No link with the network is detected.

•Solid green. A link with the network is detected.

•Blinking green. Network trac is detected.

Package Contents

Unpack the box and verify the contents:

• WAC740 ProSAFE Dual Band Wireless AC Access Point

• Category 5e Ethernet cable

• Ceiling mount kit

LED Description

LAN LED 1

•O. A 10 Mbps Ethernet link is detected or no Ethernet link is detected.

•Solid green. A 2.5 Gbps Ethernet link is detected.

•Solid amber. A 1 Gbps or 100 Mbps Ethernet link is detected.

If both LAN LED 1 and LAN LED 2 light solid green or amber, the LAN ports

are members of a link aggregation group (LAG).

LAN LED 2

•O. No LAG is detected.

•Solid green. A LAG with a 2.5 Gbps Ethernet link is detected.

•Solid amber. A LAG with a 1 Gbps or 100 Mbps Ethernet link is detected.

If both LAN LED 1 and LAN LED 2 light solid green or amber, the LAN ports

are members of a LAG.

2.4G WLAN LED

•O. The 2.4 GHz WiFi radio is o.

•Solid green. The 2.4 GHz WiFi radio is on.

•Blinking green. WiFi activity is detected on the 2.4 GHz WiFi radio.

5G WLAN LED

•O. The 5 GHz WiFi radio is o.

•Solid green. The 5 GHz WiFi radio is on.

•Blinking green. WiFi activity is detected on the 5 GHz WiFi radio.

The access point uses a DHCP client that is enabled by default. If your network

includes a DHCP server, the access point obtains an IP address from the DHCP

server. If your network does not include a DHCP server, the access point sets

its IP address to a static IP address of 192.168.0.160.

If your network includes a DHCP server, note the following:

• Make sure that Option 43 is enabled on the DHCP server.

• Make sure that the DHCP server speciﬁes the IP address of the wireless

controller in the required hexadecimal format in the Option 43 ﬁeld.

For example, if the IP address of the wireless controller is 192.168.0.250,

you must enter the hexadecimal string 02:04:C0:A8:0:FA.

To compose the address, start with 02:04: and then add each of the four

address octets in hexadecimal format, separated by colons.

The ﬁrst two octets (02:04) deﬁne a standalone NETGEAR wireless

controller, or in a stack, the ﬁrst wireless controller in the stack.

July 2016

are trademarks of NETGEAR, Inc. Any non‑NETGEAR

trademarks are used for reference purposes only.

NETGEAR, Inc.

350 East Plumeria Drive

San Jose, CA 95134, USA

NETGEAR INTL LTD

Building 3, University Technology Centre

Curraheen Road, Cork, Ireland

To specify the second wireless controller in the stack, enter the ﬁrst two

octets as 02:08. To specify the third wireless controller in the stack,

enter the ﬁrst two octets as 02:0C.

The remaining four octets specify the IP address in hexadecimal format.

• We recommend that you reserve an IP address for the access point on

the DHCP server.

If your network does not include a DHCP server, conﬁgure a computer with

a static IP address of 192.168.0.210 and a subnet mask of 255.255.255.0

so that you can connect to the access point at IP address 192.168.0.160.

¾To verify that the access point obtained IP address information,

or if your network does not include a DHCP server, to conﬁgure

the access point’s IP address information:

1. Open a web browser from a computer that is connected to the same

network as the access point or to the access point directly through an

Ethernet cable.

2. In the address bar, enter the IP address of the access point.

The default IP address is .192.168.0.160

A login window displays.

3. Enter the user name and password.

The user name is . The default password is admin password. The user

name and password are case-sensitive.

4. Select Conﬁguration > System > Basic > Network Settings > IP

Settings.

5. Verify or conﬁgure the IP settings for your network.

6. Select Conﬁguration > System > Network Settings > Controller

Settings.

7. Verify or conﬁgure the IP address for the wireless controller in the

network.

For more information, see the ProSAFE wireless controller user manual.

Problem Cause Possible Solution

No LEDs are lit

on the access

point.

The access point

is receiving no

power.

•Make sure that the access point is securely connected to a PoE+ switch.

•Make sure that the PoE+ switch is connected to a power source.

The Power

LED alternates

green and

amber.

The access point

is receiving

insucient PoE

power.

•Make sure that PoE+ switch is not overloaded.

•If you connected the access point to a PoE (802.3af) switch, disconnect

it and connect it to a PoE+ (802.3at) switch instead. The access point

requires a PoE+ (802.3at) switch.

The LAN port

LEDs are o.

A hardware

connection

problem exists.

•Make sure that the cable is connected to LAN port 1 (the PoE port) on

the access point. (LAN port 2 active only when a LAG is enabled.)

•Make sure that the cable connectors are securely plugged into the

access point and switch.

• Make sure that the switch is turned on.

The WLAN

LEDs are o.

The wireless

connection does

not work.

•Make sure that the PoE+ switch is providing sucient power to the

access point.

•From the wireless controller, verify that the radio or radios are turned on.

•If the WLAN LEDs remain o, contact NETGEAR.

You cannot

connect to

the access

point from a

browser.

Multiple

possible causes.

•Make sure that your computer is using an IP address in the same

range as the access point. The access point default IP address is

192.168.0.160, and the default subnet mask is 255.255.255.0.

•Quit the browser, clear the cache, delete the cookies, and launch the

browser again.

Support

Thank you for purchasing this NETGEAR product. You can visit

www.netgear.com/support to register your product, get help, access the latest

downloads and user manuals, and join our community. We recommend that you

use only ocial NETGEAR support resources.

For more information about the installation options, visit

www.netgear.com/support to access the hardware installation guide.

For the current EU Declaration of Conformity, visit

http://support.netgear.com/app/answers/detail/a_id/11621/.

For regulatory compliance information, visit

http://www.netgear.com/about/regulatory/.

See the regulatory compliance document before connecting the power supply.

¾To let the wireless controller discover the access point:

1. Access the wireless controller at its network IP address.

2. Select Access Point > Discovery Wizard.

3. Follow the steps onscreen to discover the access point and review the

discovery results.

4. In the table with discovered access points, select the check box for the

access point, and click the button.Add

The access point is added to the Managed AP List and is now ready for

further conﬁguration and management by the wireless controller.

For more information, see the ProSAFE wireless controller user manual.

Deploy the Access Point

The best location for the access point is elevated, such as mounted on a

wall or ceiling, at the center of the WiFi coverage area, and within line of

sight of all mobile devices.

For information about mounting the access point, see the ceiling and wall

installation guide for the WAC720, WAC730, and WAC740 access points.

¾To deploy the access point:

1. Disconnect the access point and position it where you will deploy it.

2. Connect an Ethernet cable from the access point to a LAN port on a

PoE+ switch.

3. Make sure that the PoE+ switch and the wireless controller are

connected.

4. Using a WiFi device, verify connectivity by connecting to the access

point and use a browser to connect to the Internet.

Troubleshooting Tips

The following table provides some tips for correcting simple problems

that you might encounter. For more troubleshooting information, see the

troubleshooting chapter in the ProSAFE wireless controller user manual.

Especificaciones del producto

Marca:	Netgear
Categoría:	punto de acceso
Modelo:	ProSafe WAC740
Color del producto:	Zwart, zilver
Peso.:	250 g
Ancho:	68 mm
Profundidad:	18 mm
Altura:	84 mm
red LAN:	Nee
Sensibilidad:	1.2 μV
Relación señal-ruido:	62 dB
Número de canales:	188 kanalen
Micrófono de respuesta de frecuencia:	50 - 15000 Hz
Rango de radiofrecuencia:	638.125 - 661.875 MHz
Tipo frecuencia de trabajo:	Ultrahoge frequentie (UHF)
Supresión de canales adyacentes.:	70 dB
Atenuación de intermodulación:	65 dB