Netgear WG103 Manual de Usario
Netgear
punto de acceso
WG103
Lee a continuación 📖 el manual en español para Netgear WG103 (2 páginas) en la categoría punto de acceso. Esta guía fue útil para 4 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/2
)NSTALLATION'UIDE
Please refer to the Reference Manual on your Resource CD for instructions about
advanced configuration options.
Estimated Installation Time: 30 minutes.
Tip: Before mounting the WG103 in a high location, first set up and test the WG103 to
verify wireless network connectivity.
1. Connect the WG103 to the Computer
a. Unpack the box and verify the contents.
b. Prepare a PC with an Ethernet
adapter. If this PC is already part
of your network, record its
TCP/IP configuration settings.
Configure the PC with a static IP
address of 192.168.0.210 and
255.255.255.0 as the subnet mask.
c. Connect an Ethernet cable from
the WG103 to the PC (point A in
the illustration).
d. Securely insert the other end of the
cable into the WG103 Ethernet
port (point B in the illustration).
A
B
e. Turn on your computer, connect the power adapter to the WG103 and verify the
following:
•Power: The power light should be lit. If the power light is not lit, check the
connections and check to see if the power outlet is controlled by a wall
switch that is turned off.
•Test: The test light should be blinking when the WG103 is first turned on.
•LAN: The LAN light should be lit (amber for a 10 Mbps connection and
green for a 100 Mbps connection). If not, make sure the Ethernet cable is
securely attached at both ends.
2. Configure LAN and Wireless Access
a. Configure the WG103 Ethernet port for LAN access.
•Connect to the WG103 by opening your browser and
entering http://192.168.0.229 in the address field.
• When prompted, enter admin for the user name and
password for the password, both in lower case letters.
• Click the Basic Settings link and configure the IP Settings for your network.
b. Configure the wireless interface for wireless access. See the online help or the
Reference Manual for full instructions.
c. Test wireless connectivity using a PC with a wireless adapter configured
according to the wireless settings you just set in the WG103 to establish a
wireless connection to the WG103.
Now that you have finished the setup steps, you are ready to deploy the WG103 in
your network. If needed, you can now reconfigure the PC you used in step 1 back to
its original TCP/IP settings.
1. Disconnect the WG103 and position it where you will deploy it. The best location is
elevated, such as wall mounted or on the top of a cubicle, at the center of your
wireless coverage area, and within line of sight of all the mobile devices.
2. Position the antenna. Vertical positioning provides best side-to-side coverage.
Horizontal positioning provides best top-to-bottom coverage.
3. Connect an Ethernet cable from your WG103 to a LAN port on your router, switch, or
hub.
4. Connect the power adapter to the wireless access point and plug the power adapter in
to a power outlet. The Power and LAN lights should light up.
Tip: The WG103 supports Power Over Ethernet (PoE). If you have a switch that
provides PoE, you will not need to us to power the WG103. e the power adapter
This can be especially convenient when the WG103 is installed in a high
location far away from a power outlet.
Using a computer with an 802.11g or 802.11b wireless adapter, verify connectivity by
using a browser such as Internet Explorer or Mozilla Firefox to connect to the Internet, or
check for file and printer access on your network. In order to connect to the Internet, your
network must include a router that provides Internet access.
Note: If you cannot connect, see to Troubleshooting Tips in this guide or the Reference
Manual on the Resource CD for the ProSafe® 802.11g Wireless Access Point.
WG103_IG.fm Page 1 Monday, March 30, 2009 12:45 PM
March, 2009
This symbol was placed in accordance with the European Union Directive 2002/96 on
the Waste Electrical and Electronic Equipment (the WEEE Directive). If disposed of
within the European Union, this product s cled in accordance hould be treated and recy
with the laws of your jurisdiction implementing the WEEE Directive.
© 2009 by NETGEAR, Inc. All rights reserved. NETGEAR and the NETGEAR logo are registered
trademarks of NETGEAR, Inc. in the United States and/or other countries. Other brand and product
names are trademarks or registered trademarks of formation is subject to their respective holders. In
change without notice.
Here are some tips for correcting simple problems you may have.
The wireless access point has no power:
• Make sure the power cord is connected to the access point and plugged in to a
working power outlet or power strip.
• Make sure you are using the correct NETGEAR power adapter supplied with your
access point.
There is a hardware connection problem:
• Make sure the cable connectors are securely plugged in at the access point and the
network device (hub, switch, or router).
• Make sure the connected device is turned on.
The wireless access point’s antennas are not working:
• If the Wireless LAN activity light stays off while the WG103 is transmitting or
receiving data, disconnect the adapter from en plug it in again.its power source and th
• Make sure the antennas are tightly connected to the WG103.
• Contact NETGEAR if the Wireless LAN light remains off while the WG103 is
transmitting or receiving data.
Check these items:
• The WG103 is properly installed, LAN connections are OK, and it is powered on.
Check that the LAN port LED is green to verify that the Ethernet connection is OK.
• If you are using the NetBIOS name of the WG103 to connect, ensure that your PC
and the WG103 are on the same network segm a WINS server on ent or that there is
your network.
• If your PC uses a fixed (static) IP address, ensure that it is using an IP address in the
range of the WG103. The WG103 default IP address is 192.168.0.229 and the default
subnet mask is 255.255.255.0. The WG103 default setting is for a static IP address.
• If the network where you are connecting it is using DHCP, configure it accordingly.
See the Reference Manual on the for the ProSafe® 802.11g Wireless Resource CD
Access Point for more details.
There is a configuration problem. Check these items:
• You may not have restarted the computer with the wireless adapter to have TCP/IP
changes take effect. Restart the computer.
• The computer with the wireless adapter may not have the correct TCP/IP settings to
communicate with the network. Restart the computer and check that TCP/IP is set up
properly for that network. The usual setting for Windows on the Network Properties
is set to “Obtain an IP address automatically.”
• The WG103’s default values may not work with your network. Check the WG103
default configuration against the configuration of other devices in your network.
• For full instructions on changing the access point’s default values, see the
Reference Manual on the Resource CD for the ProSafe® 802.11g Wireless Access
Point.
Thank you for selecting NETGEAR products.
After completing the Smart Wizar e the serial number on the d configuration assistant, locat
bottom label of your product, and use it to register your product at
http://www.NETGEAR.com/register.
Registration is required before you can use our telephone support service. Registration via
our website is strongly recommended. Go to http://kbserver.netgear.com for product
updates and Web support For Warranty and Regional Customer Support information, see .
the Resource CD that came with your product.
WG103_IG.fm Page 2 Monday, March 30, 2009 12:45 PM
Especificaciones del producto
| Marca: | Netgear |
| Categoría: | punto de acceso |
| Modelo: | WG103 |
¿Necesitas ayuda?
Si necesitas ayuda con Netgear WG103 haz una pregunta a continuación y otros usuarios te responderán
punto de acceso Netgear Manuales
12 Octubre 2024
19 Septiembre 2024
3 Agosto 2024
1 Agosto 2024
27 Julio 2024
27 Julio 2024
22 Julio 2024
18 Julio 2024
punto de acceso Manuales
- punto de acceso HP
- punto de acceso Allnet
- punto de acceso Allied Telesis
- punto de acceso Airlive
- punto de acceso Edimax
- punto de acceso Asus
- punto de acceso Renkforce
- punto de acceso Sitecom
- punto de acceso TP Link
- punto de acceso Fortinet
- punto de acceso DataVideo
- punto de acceso Totolink
- punto de acceso Cisco
- punto de acceso Engenius
- punto de acceso Netis
- punto de acceso Draytek
- punto de acceso Devolo
- punto de acceso Linksys
- punto de acceso Buffalo
- punto de acceso Dahua Technology
- punto de acceso LevelOne
- punto de acceso Dell
- punto de acceso Planet
- punto de acceso Zebra
- punto de acceso D-Link
- punto de acceso Aruba
- punto de acceso Tenda
- punto de acceso Ubiquiti Networks
- punto de acceso Trendnet
- punto de acceso Mikrotik
- punto de acceso EQ3
- punto de acceso Homematic IP
- punto de acceso Hawking Technologies
- punto de acceso INCA
- punto de acceso LigoWave
- punto de acceso StarTech.com
- punto de acceso Advantech
- punto de acceso Intellinet
- punto de acceso Lancom
- punto de acceso SMC
- punto de acceso V7
- punto de acceso NUVO
- punto de acceso Cudy
- punto de acceso IP-COM
- punto de acceso Cambium Networks
- punto de acceso AMX
- punto de acceso Ruckus Wireless
- punto de acceso Bintec-elmeg
- punto de acceso Mach Power
- punto de acceso Brocade
- punto de acceso ICC
- punto de acceso Insteon
- punto de acceso Juniper
- punto de acceso Comtrend
- punto de acceso Premiertek
- punto de acceso Extreme Networks
- punto de acceso Atlantis Land
- punto de acceso Mojo
- punto de acceso FlyingVoice
- punto de acceso Luxul
Últimos punto de acceso Manuales
26 Octubre 2024
26 Octubre 2024
26 Octubre 2024
18 Octubre 2024
18 Octubre 2024
17 Octubre 2024
14 Octubre 2024
13 Octubre 2024
11 Octubre 2024
9 Octubre 2024