Ozito BDP-450 Manual de Usario

Ozito taladradora BDP-450

Lee a continuación 📖 el manual en español para Ozito BDP-450 (8 páginas) en la categoría taladradora. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/8

PEDESTAL

DRILL PRESS

450W

INSTRUCTION MANUAL

SPECIFICATIONS

Mains Voltage: 230–240V ~ 50Hz

Power: 300W (S1);

450W (S6 20%)

No Load Speed: 600 - 2,650/min

Chuck: Ø13mm Keyed

B16 Morse Taper

Chuck Size: Ø1.5 - 13mm

Max. Drilling Depth: 50mm

Table Tilt: 0-450 (Left & Right)

Weight: 13kg

BDP-450

STANDARD EQUIPMENT

3 YEAR REPLACEMENT WARRANTY*

Your product is guaranteed for a period of If 36 months from the original date of purchase.

a product is defective it will be replaced in accordance with the terms of this warranty. Warranty

excludes consumable parts, for example: valve adapters and accessories.

*This product is intended for DIY use only and replacement warranty covers domestic use.

WARNING

The following actions will result in the warranty being void.

• If the tool has been operated on a supply voltage other than that speciﬁed on the tool.

• If the tool shows signs of damage or defects caused by or resulting from abuse, accidents

or alterations.

• Failure to perform maintenance as set out within the instruction manual.

• If the tool is disassembled or tampered with in any way.

• Professional, industrial or high frequency use.

WARRANTY

Ozito Industries Pty. Ltd. 25 Fox Drive, Dandenong South, Victoria, Australia 3175.

ozito.com.au

Head Assembly, Table, Baseplate &

Main Column

Chuck Guard, Guard Arm, 3 x Feed

Wheel Handles & Belt Tension

Handle

Chuck, Chuck Key, 3 x Column Bolts

& 2 x Hex Keys

0622

IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY

YOU MUST RETURN THE PRODUCT TO YOUR NEAREST

BUNNINGS WAREHOUSE WITH YOUR BUNNINGS

PRODUCT FOR WARRANTY PLEASE TELEPHONE OUR

CUSTOMER SERVICE HELPLINE:

Australia: 1800 069 486

New Zealand: 0508 069 486

The beneﬁts provided under this warranty are in addition to other rights and remedies which

are available to you at law.

Our goods come with guarantees that cannot be excluded at law. You are entitled to a

replacement or refund for a major failure and for compensation for any other reasonably

foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the

goods fail to be of acceptable quality and the failure does not amount to a major failure.

Generally you will be responsible for all costs associated with a claim under this warranty,

however, where you have suffered any additional direct loss as a result of a defective product

you may be able to claim such expenses by contacting our customer service helpline above.

TO ENSURE A SPEEDY RESPONSE PLEASE HAVE

THE MODEL NUMBER AND DATE OF PURCHASE

AVAILABLE. A CUSTOMER SERVICE REPRESENTATIVE

WILL TAKE YOUR CALL AND ANSWER ANY QUESTIONS

YOU MAY HAVE RELATING TO THE WARRANTY POLICY

OR PROCEDURE.

Assembling The Drill Press

1. Carefully remove the contents from the packaging.

2. Select a ﬁrm, level surface on which to assemble the drill press.

3. Align the holes on the base

of the main column with the

holes in the baseplate.

4. Place a washer onto each of

the 3 column bolts and use

these to fasten the column

into place; use an M10

wrench to tighten securely.

5. Rotate the table lever anti-clockwise

to loosen the collar.

6. Slide the table collar onto

the column and secure

at the desired position by

tightening the collar bolt.

7. Place the motor unit on the

main column and use a 4mm

hex key to tighten the grub

screw on the side of the

motor unit.

8. Screw the 3 feed wheel

handles into the slots on the

feed wheel hub.

9. Screw the belt tension handle into

the slot on the belt tension hub.

1. Belt Tension Lever

2. On/Off Switch

3. Guard Arm Lock

4. Guard Arm

5. Pulley Cover

6. Motor

7. Main Column

8. Table Lever

9. Baseplate

10. Table Tilt Bolt

11. Table

12. Chuck Guard

13. Guard Locking Screw

14. Keyed Chuck

15. Depth Indicator Lock

16. Motor Locking Screw

17. Chuck Key Holder

18. Feed Wheel Handle

19. Pulley Cover Lock

PEDESTAL DRILL PRESS

KNOW YOUR PRODUCT

1. ASSEMBLY

SETUP & PREPARATION

WARNING! ENSURE THE TOOL IS TURNED OFF AND

DISCONNECTED FROM THE POWER SUPPLY BEFORE

PERFORMING ANY OF THE FOLLOWING OPERATIONS.

ONLINE MANUAL

Scan this QR Code with your mobile

device to take you to the online manual.

Installing The Chuck & Chuck Guard

1. With the chuck jaws fully

retracted into the chuck,

align the chuck with the

spindle and place it the drill

table.

2. Raise the table until the

chuck is approximately

25mm from the spindle.

Note: Use a piece of timber to protect the chuck and avoid

scratches.

3. Use the feed wheel handles

to slowly lower the spindle

until the chuck is pushed

securely onto the spindle.

Note: A gentle tap on the

timber is required to secure the

keyed chuck onto the tapered

drive shaft

4. Remove the 2 screws on the side of the guard

arm with a screwdriver (not supplied) and slide

it into the arm holder on the motor unit.

Note: Ensure the 2 screws and guard arm lock

knob will face the user when reassembled.

5. Tighten the stop screw.

6. Align the holes on the chuck

guard with the holes on the

guard arm and reﬁt the 2

removed screws to hold the

guard in place.

7. Use the guard locking screw to

lock the guard arm in the desired

position.

Attaching A Drill Bit

1. Swing the chuck guard out

of the way.

2. Push the chuck key into

any of the holes in the side

of the chuck and turn it

anti-clockwise to loosen the

chuck jaws.

3. Insert the drill bit fully into

the chuck.

4. Hold the drill bit in one hand

and rotate the chuck key

clockwise to tighten the jaws

around the drill bit.

Note: Ensure drill bit is straight

before fully tightening.

Note: Tighten the chuck jaws

from all 3 holes with the chuck key fasten the drill bit securely.

5. Swing the chuck guard back

into place and store the

chuck key in the holder on

the side of the motor unit.

25mm

Especificaciones del producto

Marca:	Ozito
Categoría:	taladradora
Modelo:	BDP-450
Color del producto:	Black, Grey
Peso.:	839 g
Ancho:	124 mm
Profundidad:	171 mm
Altura:	127 mm
Material:	Staal
Compatibilidad:	AVer CAM540
Incluyendo tornillos:	Ja
Número-de-productos-incluidos:	1 stuk(s)
Cable de conexión:	1/4-20 "