PAC RPK5-GM4101 Manual de Usario

PAC equipo de coche RPK5-GM4101

Lee a continuación 📖 el manual en español para PAC RPK5-GM4101 (9 páginas) en la categoría equipo de coche. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/9

Page 1

PAC® | 866-931-8021 | support@pac-audio.com

www.pac-audio.com Rev. 113016

P ifi A C ti

PAC is an AAMP power brand

RPK5-GM4101

Complete Radio Replacement Kit with

Integrated Climate Control Retention for

2010-2015 Chevrolet Camaro

Removing the factory radio from the vehicle

1.1 - Apply the parking brake. Move the transmission shift

assembly to the most rearward position possible. Use a

at bladed plastic trim tool and release the retainer tabs

securing the front oor console front cover to the console

assembly. Lift the cover (1) up and rearward making sure that

the accessory power receptacle and the electronic traction

control switch clears the transmission shift assembly. It may be

necessary to pop them loose from the underside to achieve

clearance. Disconnect the electrical connections.

1.2 - Remove the 2 x 7mm bolts (1) securing the radio

control assembly (2) into the dash. Then use a at-

bladed plastic trim tool in order to release the retainer

clips securing the radio control assembly (2) to the

instrument panel. Disconnect the electrical connections.

Parts List

The RPK5-GM4101 includes everything you need for a professional installation of an aftermarket radio in your Camaro.

This kit contains:

1. Dash Kit

• (x1) PAC HVAC Control Panel (Transfer of the factory HVAC knobs is required. See instructions below)

• (x2) Radio Mounting Brackets (One left and one right)

• (x1) Pocket (For single din applications)

• (x8) Radio Mounting Screws

2. RP5-GM4101 (Camaro specic radio replacement module)

3. Camaro specic antenna adapter (BAA-DIN22).

4. Rear camera retention cable for vehicles equipped with the MyLink system.

5. USB retention cable. This cable is compatible with vehicles equipped with the MyLink radios and vehicles equipped with the

standard non-touchscreen radios. It will require that the cable be ran to the back of the center console.

6. AUX retention cable for 2010-2012 vehicles equipped with the standard non-touchscreen radios also equipped with a USB port.

Overview

The RPK5-GM4101 is a complete radio replacement kit with integrated climate control retention for the 2010-2015 Chevrolet

Camaro. This kit utilizes the factory HVAC control knobs for a more factory look and experience. To add to the factory look

and experience the exterior temperature display is retained by a small OLED display at the top of the kit retaining this valuable

vehicle feature. This kit also includes all of the modules and cables needed to retain all of the important features of the factory

system such as OnStar, factory warning chimes, factory Bluetooth, steering wheel mounted radio controls, factory reverse

camera, factory amplier (if equipped), AM/FM reception, factory AUX jack (if equipped) and the factory USB port (if equipped).

Table of Contents: Page:

1. Factory Radio Removal ------------------------------------------------------ 1-2

2. Disassembly of the factory HVAC control module --------------------- 2-3

3. Assembly of the PAC HVAC control module ---------------------------- 3-4

4. RP5-GM4101 Instructions --------------------------------------------------- 4-6

5. AUX & USB Cable Installation ------------------------------------------------ 7

6. Temperature Display Settings ------------------------------------------------- 7

7. Sub-Dash Preparation ----------------------------------------------------------- 7

8. Kit Assembly Instructions ------------------------------------------------------- 8

9. Installation of the PAC HVAC control module --------------------------- 8-9

Page 2

RPK5-GM4101

Complete Radio Replacement Kit with

Integrated Climate Control Retention for

2010-2015 Chevrolet Camaro

PAC® | 866-931-8021 | support@pac-audio.com

www.pac-audio.com Rev. 113016

P ifi A C ti

PAC is an AAMP power brand

Disassembly of the factory HVAC control panel

The following steps will aide you in the disassembly of the HVAC control panel so that the factory

HVAC control knobs and supports can be reused in the PAC RPK5-GM4101 Integrated Kit.

2.6 - Be sure to keep the screws

separated as there are different lengths

and diameters.

2.5 - Using a at bladed pry tool remove two

of the white fasteners off of the black plastic

backing.

2.4 - Remove the 10 Phillips head screws

shown below and remove the black plastic

backing.

2.2 - Pry outwards on the clips on either side

of the plastic trim that surrounds the white

connector.

2.3 - Once the plastic trim is removed, locate

the 16 pin connector shown below. Using a

at bladed tool, press in the grooves on both

sides, pry upward and away from the circuit

board, to release the connector.

2.1 - Remove the 2 Phillips head screws

shown below.

1.3 - Remove the 4 x 7mm bolts (1) securing the radio

(2) into the dash. Slide the radio (2) to the rear and

disconnect all electrical connections.

You can set the radio aside as it will not be used fur-

ther. For the next section, you will be working with

the factory HVAC control panel to utilize the HVAC

knobs allowing for more of a factory experience

when using the PAC RPK5-GM4101.

Proceed to the next section to begin disassembly of

the factory radio control assembly.

Removing the factory radio from the vehicle (cont.)

Page 3

PAC® | 866-931-8021 | support@pac-audio.com

www.pac-audio.com Rev. 113016

P ifi A C ti

PAC is an AAMP power brand

RPK5-GM4101

Complete Radio Replacement Kit with

Integrated Climate Control Retention for

2010-2015 Chevrolet Camaro

Disassembly of the factory radio control assembly (cont.)

2.7 - Remove the 12 Phillips head screws

shown below.

2.8 - Be sure to keep the screws separated

as they will be used during the assembly

stage later.

2.9 - After the screws have been removed,

remove the HVAC knobs by pulling them

from the front of the faceplate being careful

not to bend the contacts on either end of the

contact swiper on the backside of each of

the knobs.

2.10 - Look inside the opening where the

knobs were removed. Remove the 2 Phillips

screws shown below. Do this for both

openings.

2.11 - Remove the 2 support brackets and

keep handy as they will be used in the next

step.

Assembly of the PAC HVAC control assembly

3.2 - Secure the 2 support brackets to

the circuit board using the same screws

removed from Disassembly step # 9. The

screws will pass through the board and

thread into the brackets via the holes dened

below. Be sure that the alignment tabs are

seated properly.

3.1 - Secure the 2 support brackets to the

PAC HVAC control assembly using 4 of the

same screws shown in disassembly step #

7. Do this to the back of each side. Be sure

that the alignment tabs are seated properly

in the circuit board to the front.

3.3 - Position the knobs in the proper opening

so that the buttons are straight and insert

them into the opening. With VERY LITTLE

force rotate them slightly left and right while

pushing them towards the PCB. Once the

alignment tabs are lined up they should click

and lock into place. Use extra caution as the

contacts could bend while rotating.

Especificaciones del producto

Marca:	PAC
Categoría:	equipo de coche
Modelo:	RPK5-GM4101
Color del producto:	Black, Stainless steel
Material de la carcasa:	Roestvrijstaal
Activos:	2000 W
Número de rebanadas:	4 snede(n)
Luz indicadora:	Ja
Rejilla para sándwiches:	Ja
Mango(s) frío(s):	Ja
voltaje-de-entrada-de-CA:	220 - 240 V
Frecuencia-de-entrada-de-CA:	50 - 60 Hz