Pyle PLML50FB Manual de Usario

Pyle Altavoz de subgraves PLML50FB

Lee a continuación 📖 el manual en español para Pyle PLML50FB (18 páginas) en la categoría Altavoz de subgraves. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/18
AM/FM/MP3/USB/AUX Stereo Receiver, Single DIN,
30 Preset Memory Stations, LCD Display
with Remote Control (Black)
PLML50FB
Stereo Receiver Power Amplifier
www.PyleUSA.com
2
INSTALLATION
Preparation
The preparation kit is necessary to mount the radio on the dashboard, this kit is
available at electronics stores and car audio specialists, check the installation
kit before using it to make sure it is the right one for your vehicle.
INSTALL THE DEVICE
1. Lift the left or right top corner of the plastic outer trim ring then pull it out to
remove it.
2. Insert the two bracket keys into the left and right side of the chassis to
separate the chassis from the housing.
3. Install the mounting knob on the board. Check the opening size of the sliding
panel to be mounted. If the measurement is not large enough, carefully cut it
until it slips easily on the opening. Do not force the handle in the opening so
as not to bend it. Locate the series of dubbing tabs above, below and all sides
to be mounted. Completely insert it to the opening of the board, bend the
tabs as necessary towards outside to ensure it ts the board.
4. Slide the stereo into the opening in the dash, ensuring that the wires behind
are tucked and not pinched.
5. Follow the wiring diagram carefully. Verify you've connected them correctly.
Connect the unit to a 12 Volt power source with adequate ground.CAUTION!
6. Now that your wires are all completed, attach the front panel and turn theON
unit (the vehicle must be switched on). If the unit does not work, check the
calibration again until the problem is solved. With the new car stereo secured
into the bracket, all you need to do is plug the wiring harness back into the
stereo and put the assembly back into place.
7. Slide the stereo into the opening in the dash, ensuring that the wires behind
are tucked and not pinched. Sometimes this may take a few times when the
vehicle has a tight dash opening. Tuck the wires back into an opening behind
the unit.
8. Install the plastic outer trim ring
9. Snap all the pieces of trim back into place over the stereo. Double check that
all screws and trim pieces are securely in place.Try out the new stereo.
Turn the car power on again and play around with the stereo and its settings
to be sure everything is in working order.
www.PyleUSA.com 3
WIRING CONNECTIONS
HARDS FREE PUSH-TO-TALK
PUSH-TO-TALK
• Allows you to access SIRI GOOGLE voice or via Wireless BT.
• Your phone must support SIRI or GOOGLE voice. Once connected to BT, your
phone will ask for access to your contact list.
• Now you are ready to use PUSH-TO-TALK PUSH-TO-TALK. Press the icon.
You are ready to talk. Call "(CONTACT NAME)", the system will call without
having to use your phone.
CONTROL PANEL BUTTONS
15A
Front C utput(Left)R A O Front C utput( ight)R A O R
R A Oear RC utput(Left)
R A O Rear RC utput( ight)
EXternal MIC
SWC
AN RADIO ANTENNA JAT: CK
F-L:Front C utput(Left)R A O
F-R: R A O RFront C utput( ight)
R-L:R R A Oear C utput(Left)
R-R:R R A O Rear C utput( ight)
Power/speaker Connector
FUSE 15A
PRECAUTION
+12V DC
NEGATIVE
EARTH
www.PyleUSA.com
4
CONTROL PANEL BUTTONS
1. (Power)/Mode (source) button
2. (select/menu) button and (volume) knobSEL VOL
3. Back to the previous conguration point;
Press /Bass enhances the pulse function
4. Short press button display clock in all mode. In USB mode, Short press to
select All info/Elapsed time/File info/Track info/clock operation.
Press and hold button turn o illumination on panel and touch any button
to turn on illumination.
5. Folder up
6. Folder down
7. (repeat), button 3 presetRPT
8. (random), button 4 presetRDM
9. (pause/start), preset station 5 button
10. (intro), preset button 6 stationINT
11. Press and hold BND button to activate SIRI. Short press BND button
to change band. Short press BND button to pick up/cut o phone call.
12. (tune back, search back, crawl back, fast reverse)
13. (tune forward, search forward, crawl forward, fast forward)
14. remote control sensorIR
15. LCD screen
16. (automatic storage/preset station search, automatic search)AS
17. USB port
18. AUX IN (auxiliary input)
19. input (integrated microphone)MIC
20. In power mode, press the button to toggle mute or .ON MUTE ON OFF
21. RESET
GENERAL OPERATION
Turn Unit ON/OFF
• Press the power /Mode ON button on the front panel to turn the unit, and
press and hold it again to turn the unit.OFF
• Press the power button on the remote control to turn the unit ON or OFF.
www.PyleUSA.com 5
Adjust Volume (VOL)
• Rotate the VOL knob on the front panel or press the button VOL+ /VOL-
on the remote control to increase or decrease the volume level.
FUNCTION
Press the Volume knob and Rotate to select Audio/Display/Tuner/Clock/Beep/
Animation/Demo mode function. Press the Volume knob again to select desire
function mode.
AUDIO MODE
• Press the Volume knob and Rotate to select SW Level/Manual EQ/Q factor/
Preset EQ/Bass boost/Loudness/Subwoofer set/Fader/Balance/X’Over/DTA
Setting/Car type.
• Press and hold Volume knob to select 2 way/3 way X’Over mode.
SW LEVEL
Press the Volume knob and Rotate to select -13 ~ +13 level.
MANUAL EQ
Press the Volume knob and Rotate to select 25 band frequencies level.
Q FACTOR
Press the Volume knob and Rotate to select 1/1.5/2.5/3.5 different Q factor value.
PRESET EQ
Press the Volume knob and Rotate to select user/Natural/Rock/Pop/Easy/
Top 40/Jazz/Powerful.
BASS BOOST
Press the Volume knob and Rotate to select Bass boost level.
LOUDNESS
Press the Volume knob and Rotate to select Loudness level.
SUBWOOFER SET
Press the Volume knob and Rotate to switch ON/OFF.
FADER
Press the Volume knob and Rotate to select Fader position.
BALANCE
Press the Volume knob and Rotate to select Balance position.
www.PyleUSA.com
6
X’OVER
Press the Volume knob and Rotate to select Tweeter/Front HPF/Rear HPF/
Subwoofer LPF.
TWEETER
Press the Volume knob and Rotate to select Frequency/Gain left/Gain right.
FRONT HPF
Press the Volume knob and Rotate to select Frequency/Gain.
REAR HPF
Press the Volume knob and Rotate to select Frequency/Gain.
SUBWOOFER LPF
Press the Volume knob and Rotate to select Frequency/Gain/Phase.
DTA SETTING
Press the Volume knob and Rotate to select Position/Distance/Gain/Data Reset/
Delay Unit.
CAR TYPE
Press the Volume knob and Rotate to select Small/Medium/Large car type.
DISPLAY
Press the Volume knob and Rotate to select Color Select/Spectrum/ID3 tag/
Version/Dimmer.
LANGUAGE SELECTION
Press Volume button to select language, turn the knob to select English/Russian.
COLOR SELECT
Press the Volume knob and Rotate to select custom R/G/B/ Variable Scan/Red/
Pink/Purple/Blue/Cyan/Green/Yellow/Orange.
www.PyleUSA.com
8
Set the clock (CLK)
1. To display the Time press the button.CLK
2. To set the time, press and hold the button and the time will start ashing.CLK
3. Press the or button on the front panel or on the remote control to set
the time.
4. Press the button and the minutes will start ashing.CLK
5. Press the or button on the front panel or on the remote control to set
the minutes.
6. Short Press to Increase Bass Level
Change the source mode (SRC)
Press the SRC button to switch between the button RADIO, BT (Wireless BT),
USB (with a USB device inserted), AUX-IN mode (input assistant).
Loudness: LOUD ON/OFF
Press the LOUD button on the remote control to change the loud volume to
boost the bass output frequency, press again, to turn it o.
DSP SMART ANDROID/IOS APP CONTROL
Preset Equalizer (EQ)
Press the EQ button on the front panel or on the remote control to switch
between EQ, OFF, CLASS, ROCK, POP, FLAT.
USB port
The USB port on this stereo device is designed for playing media from USB
memory devices.
Subwoofer Control Time Alignment Control
25 EQ ControlX’Over Control
www.PyleUSA.com 9
GENERAL OPERATION
Integrated Microphone
For voice reception when making a call using the hands-free system.
Auxiliary Input Connector
3.5mm auxiliary input stereo is designed for devices with line output 3.5 mm or
hearing aids.
Reset System
The button is used to reset all factory settings parameters, this function RESET
can be used when the LCD screen does not work properly or if the sound is
distorted, or when some of the controls are disable. Press the button RELEASE
to release the front panel and remove it, use a thin object with a small tip to
press the button over 6 second.RESET
Subwoofer Level Control
Select function to select audio, entry subwoofer, entry sw level, turn the knob
to select level 0-8.
Subwoofer Frequency Control
Select function to select audio, entry subwoofer, entry sw frequency, turn the
knob to select 80Hz/120Hz/160Hz.
RADIO OPERATION
Change Bands (BAND)
Press the BAND button to switch between the FM1, FM2, FM3 bands.
Each band stores up to six preset stations.
Manual Tuning ( / )
Press and hold the or button on the front panel or on the remote control
to enter manual tuning mode. In manual tuning mode, press the or
button to move the radio frequency number up or down one step.
Auto Seek Tuning ( / )
In standby mode or while not in manual tuning mode, quickly press the or
button to move to the next/previous available station automatically.
www.PyleUSA.com 11
EJECT/USB
To eject a USB device, press the button to stop playback, then remove the
USB device.
Play/Pause
Press the (play/pause) button to pause or resume playback
Next/Previous Track
• To play the next track, press the button.
• To play the previous track, press the button.
Fast Forward/Backward
• To fast forward, press and hold the button.
• To fast backward, press and hold the button.
Introduction Scan
Press the INT button to play the rst 10 seconds of each track, press again to
stop the introduction scan, and play the current track.
Repeating the same track
Press the RPT button to repeat the current track, press again to stop repeat
playback and resume normal playback.
Playing all tracks in random
Press the RDM button to play all tracks in random order, press again to cancel
this function.

Especificaciones del producto

Marca: Pyle
Categoría: Altavoz de subgraves
Modelo: PLML50FB

¿Necesitas ayuda?

Si necesitas ayuda con Pyle PLML50FB haz una pregunta a continuación y otros usuarios te responderán


Altavoz de subgraves Pyle Manuales

Pyle

Pyle PPA15 Manual de Usario

6 Octubre 2024
Pyle

Pyle PLRVST400 Manual de Usario

29 Septiembre 2024
Pyle

Pyle PLMW63 Manual de Usario

20 Septiembre 2024
Pyle

Pyle PSSUB101 Manual de Usario

16 Septiembre 2024
Pyle

Pyle PLR38I Manual de Usario

12 Septiembre 2024
Pyle

Pyle PLRG23C Manual de Usario

12 Septiembre 2024
Pyle

Pyle PLND35 Manual de Usario

12 Septiembre 2024
Pyle

Pyle PLMRB29W Manual de Usario

11 Septiembre 2024
Pyle

Pyle PLMRK47BK Manual de Usario

10 Septiembre 2024
Pyle

Pyle UPLBN122 Manual de Usario

7 Septiembre 2024

Altavoz de subgraves Manuales

Últimos Altavoz de subgraves Manuales

Canton

Canton SUB 8.2 Manual de Usario

27 Octubre 2024
Deaf Bonce

Deaf Bonce Machete MFX30D2 Manual de Usario

26 Octubre 2024
Phoenix Gold

Phoenix Gold ZP12D4 Manual de Usario

21 Octubre 2024
Phoenix Gold

Phoenix Gold ZP12D2 Manual de Usario

21 Octubre 2024
Phoenix Gold

Phoenix Gold Z12AB Manual de Usario

21 Octubre 2024
Phoenix Gold

Phoenix Gold Z10AB Manual de Usario

21 Octubre 2024
Phoenix Gold

Phoenix Gold ZB8P Manual de Usario

21 Octubre 2024
Bowers And Wilkins

Bowers And Wilkins CT 8SW Manual de Usario

20 Octubre 2024
Pioneer

Pioneer TS-W257D2 Manual de Usario

17 Octubre 2024
Vonyx

Vonyx SWP15 Manual de Usario

17 Octubre 2024