Pyle PLMRK47BK Manual de Usario

Lee a continuación 📖 el manual en español para Pyle PLMRK47BK (16 páginas) en la categoría Altavoz de subgraves. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/16
Marine Stereo Receiver Power Amplifier
AM/FM/MP3/USB/AUX/SD Card Reader Marine
Stereo Receiver, Single DIN, 30 Preset Memory Stations,
LCD Display with Remote Control
www.PyleUSA.com
2
INSTALLATION
Preparation
The preparation kit is necessary to mount the radio on the dashboard, this kit is
available at electronics stores and car audio specialists, check the installation kit
before using it to make sure it is the right one for your vehicle.
INSTALL THE DEVICE
1. Lift the left or right top corner of the plastic outer trim ring
then pull it out to remove it.
2. Insert the two bracket keys into the left and right side of
the chassis to separate the chassis from the housing.
3. Install the mounting knob on the board. Check the
opening size of the sliding panel to be mounted. If the
measurement is not large enough, carefully cut it until it
slips easily on the opening. Do not force the handle in the
opening so as not to bend it. Locate the series of dubbing
tabs above, below and all sides to be mounted. Completely
insert it to the opening of the board, bend the tabs as
necessary towards outside to ensure it ts the board.
4. Slide the stereo into the opening in the dash, ensuring that
the wires behind are tucked and not pinched.
5. Follow the wiring diagram carefully.
Verify you’ve connected them correctly.
CAUTION! Connect the unit to a 12 Volt power source
with adequate ground.
6. Now that your wires are all completed, attach the front
panel and turn the unit (the vehicle must be switched on). If the unit does not ON
work, check the calibration again until the problem is solved. With the new car
stereo secured into the bracket, all you need to do is plug the wiring harness back
into the stereo and put the assembly back into place.
7. Slide the stereo into the opening in the dash, ensuring that the wires behind are
tucked and not pinched. Sometimes this may take a few times when the vehicle
has a tight dash opening. Tuck the wires back into an opening behind the unit.
8. Install the plastic outer trim ring
9. Snap all the pieces of trim back into place over the stereo. Double check that all
screws and trim pieces are securely in place.Try out the new stereo. Turn the car
power on again and play around with the stereo and its settings to be sure
everything is in working order.
www.PyleUSA.com
3
WIRING CONNECTIONS
CONTROL PANEL BUTTONS
WIRING DIAGRAM
PRECAUTION
+12V DC
NEGATIVE
EARTH
AMPLIFIER OUTPUT
White: Rear Output
Left
White: Front Output
Left
Red: Right Front Output
Red: Rear Right Output

Especificaciones del producto

Marca: Pyle
Categoría: Altavoz de subgraves
Modelo: PLMRK47BK

¿Necesitas ayuda?

Si necesitas ayuda con Pyle PLMRK47BK haz una pregunta a continuación y otros usuarios te responderán




Altavoz de subgraves Pyle Manuales

Pyle

Pyle PLRVST400 Manual de Usario

29 Septiembre 2024
Pyle

Pyle PLMW63 Manual de Usario

20 Septiembre 2024
Pyle

Pyle PSSUB101 Manual de Usario

16 Septiembre 2024
Pyle

Pyle PLR38I Manual de Usario

12 Septiembre 2024
Pyle

Pyle PLRG23C Manual de Usario

12 Septiembre 2024
Pyle

Pyle PLND35 Manual de Usario

12 Septiembre 2024
Pyle

Pyle PLMRB29W Manual de Usario

11 Septiembre 2024
Pyle

Pyle PLMRK47BK Manual de Usario

10 Septiembre 2024

Altavoz de subgraves Manuales

Últimos Altavoz de subgraves Manuales