Remotec BW0378 - Universal Remote Control Manual de Usario

Remotec Mando a distancia BW0378 - Universal Remote Control

Lee a continuación 📖 el manual en español para Remotec BW0378 - Universal Remote Control (26 páginas) en la categoría Mando a distancia. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/26
Universal Remote Control (URC)
Operating Instructions
Télécommande Univeiselle (TCU)
Mode D’emploi
Universal - Fernbedienung (UFB)
Bedienungsanleitung
Telecomando Universale (URC)
Istruzioni Pen L’uso
Control Remoto Universal (CRU)
Instrucciones De Operacion
For English Reader .................................................................... Page 1-3
Pour Les Lecteurs Francais ....................................................... Page 4-7
Für Deutsche Leser ................................................................. Seite 8-10
Per le Lettore Italiano .......................................................... Pagina 11-13
Para Lectores De Español .................................................. Pagina 14-16
Congratulations! Your Universal Remote Control (URC) is a state-of-the-art
device which integrates many different infra-red remote controls to deliver
instant A/V action to your fingertips.
Before operating the remote, please read thoroughly (1) the interior of the
coversheet and (2) this manual. Then reserve them for future reference.
1HOW TO INSTALL BATTERIES
Alkaline batteries recommended. The number of battery required stated at
the back of the coversheet.
1. Remove the battery cover on the back of your URC.
2. Observe the polarity of the batteries and the “+/–” marks inside the battery
compartment.
3. Insert the batteries.
4. Push the battery cover back in place.
Battery Low
If the indicator flashes twice slowly after your invoking of any command, it
shows that the battery level is low. You must replace them with new batteries
to ensure proper functioning.
2HOW TO SET UP THE URC
By entering Device Code
You may setup the URC by the following code entering instructions.
1. Refer to the DEVICE CODE LIST, look up the 4-digit Device Code which
corresponds to the brands of your A/V equipment. If there are more than
one Device Code listed under your brand, try from the first code.
2. Press a desired Device Mode Key (e.g. ).
3. Hold down “ P+ ” and “ VOL– ”on the URC together simultaneously for 2
seconds until the indicator lights up.
4. Use the number keys to enter your 4-digit Device Code, the indi-
cator should go out immediately.
Turn on your device (e.g. TV), try the function keys on the URC. If your device
(e.g. TV) responds to your invoked function correctly, you have entered the
right Device Code. Otherwise, repeat the above setup instructions with the
rest available Device Codes until your device (e.g. TV) responds to your in-
voked function, and most keys work correctly.
* Simply repeat the above procedures to enter the Device Codes for your
VCR, SAT, DVD or CTV. (Remember to press a correct Device Mode Key
in step 2 above)
1
English
Note :
– DVD, CTV and other Device Codes can be entered into any device modes
except “TV” & “VCR” modes. Just simply press the device mode key
and enter your 4-digit device code for DVD, CTV and other devices.
If the indicator flashes twice in step 4, a wrong Device Code has been
entered. You are required to repeat step 2 to 4 again.
Suggestion :
– If you cannot find a correct Device Code for your equipment, see 2 HOW
TO SET UP THE URC– By Seaching Through the Library.
– You are recommended to jot down your Device Codes in the space provided
on back label after setting up the URC correctly for future reference.
TV
English
By Searching Through the Library
If you cannot identify a correct Device Code for your equipment from the Device
Code list, you may search the code through the library:-
1. Turn on your device manually (e.g. TV).
2. Press a desired Device Mode Key (e.g. ).
3. Hold down “ P+ ” and “ VOL– ” on the URC together simultaneously for 2
seconds until the indicator lights up.
4. Enter a corresponding Magic Search Code from following table. The in-
dicator should go out immediately.
DEVICE TYPE: TV VCR SAT CTV DVD
MAGIC SEARCH CODE:
0001 0002 0003 0004 0005
(e.g. press device mode key, then press “ P+ ” and “ VOL– ” , and enter
TV Magic Search Code 0001.)
5. Press the same desired device mode key again as in step 2 above. (e.g. )
6. Hold down “ P+ ” & “ VOL– ” together simultaneously for 2 seconds until
the indicator lights up, and your URC is ready to start searching.
7. Aim the URC at your device (e.g. TV), press the “ ” key repeatedly, slowly
and patiently until the device has been turned off.
Once your device has been turned off, immediately press “ P+ ” and
“ VOL– ” to lock in code and the indicator should go out.
* Simply repeat the above setup procedures to search the Device Code for
your VCR, SAT, DVD or CTV. (Remember to press a correct Device Mode
Key and correct Magic Search Code in step 2-5 above)
IMPORTANT:
– If the power on/off function of your device is not infra-red controlled - you
need to follow steps 2 to 6 above and start searching :-
• Press “ ” and another important function key alternately until your
device responds to the expected function, press “ P+ ” and “ VOL– ” to
lock in the code.
e.g. Press “ ” & “ 1 ” alternately, or ;
Press “ ” & “ ” alternately.
Note:
– DVD, CTV and other device codes can be searched and locked into any
device modes except “TV” & “VCR” modes. Just simply press the corre-
sponding device mode key in step 2 & 5 and enter an appropriate Magic
Search Code for your DVD, CTV and other devices.
– Each time you press the “ ”, the URC will skip to the next code and
send out a POWER signal trying to turn off your device.
If you failed to stop pressing “ ” in time when your device has been
turned off, turn on your device again immediately. Before the indicator
goes out, press “ ” on the URC to skip backward. Repeat the step 7
above and lock in code.
– If the indicator flashes twice after your pressing of “ ” key, you are
already at the last code of the library. Press “ P+ ” and “ VOL– ” to resume
the URC and repeat carefully the above procedures to search again.
TV
TV
TV
2

Especificaciones del producto

Marca: Remotec
Categoría: Mando a distancia
Modelo: BW0378 - Universal Remote Control

¿Necesitas ayuda?

Si necesitas ayuda con Remotec BW0378 - Universal Remote Control haz una pregunta a continuación y otros usuarios te responderán


Mando a distancia Remotec Manuales

Remotec

Remotec BW0378 - Universal Remote Control Manual de Usario

8 Septiembre 2024

Mando a distancia Manuales

Últimos Mando a distancia Manuales

Monacor

Monacor DRM-880WP Manual de Usario

27 Octubre 2024
Hama

Hama Spot-Pointer V2 Manual de Usario

26 Octubre 2024
Sony

Sony RM-ED022 Manual de Usario

21 Octubre 2024
Sonos

Sonos Control Manual de Usario

18 Octubre 2024
One For All

One For All URC 7935 Manual de Usario

18 Octubre 2024
Canon

Canon BG-E20 Manual de Usario

12 Octubre 2024
Neewer

Neewer RT112 Manual de Usario

8 Octubre 2024
Neewer

Neewer RT113 Manual de Usario

8 Octubre 2024
Logitech

Logitech Harmony 785 Manual de Usario

8 Octubre 2024
DSC

DSC WS4949 Manual de Usario

8 Octubre 2024