Revel Performa3 B110v2 Manual de Usario

Revel Altavoz de subgraves Performa3 B110v2

Lee a continuación 📖 el manual en español para Revel Performa3 B110v2 (11 páginas) en la categoría Altavoz de subgraves. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/11
B112V2/B110V2 Subwoofer
Quick Start Guide
2B112V2/B110V2 Subwoofer
Quick Start Guide
ABOUT REVEL PERFORMA3 V2
SUBWOOFERS
Thank you for purchasing a Revel Performa3 V2 subwoofer. The
B112V2 and B110V2 are powered by a 1,000-watt RMS (2,000-watt
peak) internal amplifier and feature a custom-designed transducer that
combines a new level of low frequency detail, musicality and refinement
with unprecedented brute-force visceral impact. The internal amplifier’s
high power with an integrated Parametric Equalization (PEQ) system
results in a new standard of high fidelity bass performance for home
entertainment systems.
The B112V2 and B110V2 feature 12-inch and 10-inch versions,
respectively, of a brand-new coated paper/pulp low-frequency
transducer that has been designed specifically for use in these two
subwoofer models. The primary design goal for this new driver was to
produce very low frequencies at extremely high sound pressure level
(SPL) while at the same time maintaining extremely low distortion –
qualities that are usually mutually exclusive. This new unit maintains
a precise engineering balance between the voice coil, spider and
surround that produces linear motion of all three for lower distortion by
incorporating Klippel-optimized, high-linearity motor geometry:
• The extremely long (50mm) two-layer copper voice coil wound on
a high heat-tolerant fiberglass former gives this transducer a very
large range of travel (Xmax) for dramatically increased output with
low distortion.
• A high-temperature Nomex® spider features a progressive roll
design that evenly distributes mechanical stress, helping keep
the cone’s motion linear during high-excursion operation.
• The over-sized SBR rubber surround allows greater linear
excursion while providing enhanced moving-mass control. This
material also withstands the physical breakdown typical of
common foam surrounds.
The coated cellulose/pulp cone and dustcap assembly is vented to aid in
the exchange of air, which reduces acoustic losses and increases output.
The transducer’s massive Klippel-optimized magnet assembly (19.2 lb.
in both the B112V2 and B110V2) features a double-stacked ceramic 5
magnet with a flared vent to improve airflow and reduce turbulence.
The result is increased bass output and lower distortion. A thick motor
shorting ring improves inductance linearity to further reduce distortion
and increase output. Extra cooling vents in the back plate increase
power handling and reduce power compression. Combined, these
changes increase the linear excursion 82% from the previous version.
The cast aluminum frame is fully vented to minimize acoustic losses
caused by excessive backpressure. This frame also maintains
dimensional stability and precise mechanical tolerances, allowing
the transducer to be assembled with a high degree of precision. The
structure and mass of the frame make it very strong as well as help pull
more heat away from the voice coil.
The B112V2 and B110V2 enclosures are formed with contiguous wood
layers that prevent splitting. They feature strategically-oriented bracing
that eliminates the possibility of vibration and coloration. The beautiful,
modern enclosure is finished in high-gloss piano black, walnut or white
in a process developed and overseen by Italian luxury cabinet makers
that exceeds automotive finish quality.
During development, every Revel loudspeaker model is compared to
competitive models in our unique position-independent double-blind
listening lab. This process utilizes the latest psychoacoustic research
to assure that these listening tests are valid, enabling us to verify that
all Revel loudspeakers are superior to their competitors before they are
allowed to go into production.
TABLE OF CONTENTS
About Revel Performa3V2 Subwoofers 2 ...................................................................................................................................
B112V2/B110V2 Overview 3 .......................................................................................................................................................
Subwoofer Placement Considerations..................................................................................................................................... 4
Placing a Single Subwoofer, Placing Two Subwoofers, Placing Four Subwoofers
Making Connections 6 ................................................................................................................................................................
Connecting to a Surround Processor with an Internal Crossover, Connecting to a Stereo Preamplifier,
Connecting Multiple Subwoofers, Trigger and Power Connections
Caring for Your Subwoofer....................................................................................................................................................... 9
Specifications 10 .........................................................................................................................................................................
Warranty 10 ................................................................................................................................................................................
3
B112V2/B110V2 Subwoofer
Quick Start Guide
B112V2/B110V2 OVERVIEW (Note: B112V2 and B110V2 rear panels are identical)
Input connectors: Connect these to the outputs of a stereo preamp or
connect a surround processor's subwoofer output to either the left or right
input. Balanced (XLR) and unbalanced (RCA) connectors are available. The
inputs are 0dBV nominal to +12dBV max unbal/+18dBV max bal. The XLR
input is pin 2 hot.
Low Pass Crossover: The variable 50Hz – 150Hz crossover determines
the frequency at which the subwoofer blends to the main speakers. When
the control is turned to “LFE” the crossover is by-passed and all crossover
settings are now set in the Processor or AVR menu.
NOTE: This control does not limit the frequency range of the main speakers
in the system. Adjust the Low-Pass Crossover control to properly blend to the
satellite speakers. When the blend is correct, notes of instruments and voice
in the crossover region should sound correct in level; not too loud relative to
the subwoofer frequencies or satellite frequencies, but also not too soft.
Subwoofer Gain control: Use this control to adjust the volume of the
subwoofer relative to the system’s other speakers.
Parametric Equalization (PEQ) controls: This set of equalization controls
adjust for the dominant room mode at your listening position in your specific
listening room. The parametric equalizer includes variable controls to adjust
Frequency, Bandwidth, and EQ Level of one band of frequencies. To use these
controls, you must first set the EQ switch to “ON”.
NOTE: Specific measurement equipment is required to properly adjust the
Equalization controls. Your authorized REVEL® dealer can make the appropriate
measurements, using suitable equipment to ensure optimal results.
EQ Frequency control: selects the center frequency of the particular
problem area. The range is from 32Hz to 100Hz.
EQ Bandwidth control: sets the range of frequencies over which the
equalizer will have an effect. The range is from 0.1 octaves to 0.6 octaves; the
higher the number the broader the range of frequencies that will be affected.
EQ Level control: Allows you to adjust how much boost or cut is applied
to the selected frequency by the EQ Frequency Control. This control adjusts
from -12dB to a maximum of +3dB.
EQ On/Off switch: Enables/Disables the parametric EQ controls
(Frequency, Bandwidth, and EQ Level, but not Phase).
Extended On/Off switch: In the extended mode (ON), the -3 dB point is
shifted from 29.5 Hz to 22.7 Hz in the B112V2 and from 32 Hz to 23.7 Hz in
the B110V2.
NOTE: Using the extended setting will lower the maximum volume
level the subwoofer can achieve. If you hear bass distortion during loud
passages, discontinue use of the “extended” setting.
Phase switch: adjusts the phase of the subwoofer’s output relative to
the front speakers. Proper phase adjustment can also depend on variables
such as the subwoofer placement and listener position. Set this switch for
maximum mid-bass output at the primary listening position.
12V Trigger In/Out connectors: When the subwoofer’s Power Mode
Switch is set to “Trigger,” the subwoofer will automatically turn on when
5V – 12V is present at the 12V Trigger In connection and will turn off when
the voltage at this connection is removed. Whenever the subwoofer is on, a
12V trigger signal is available at its 12V Trigger Out connector for use with
additional Performa3V2 subwoofers, or another triggerable device.
Power Mode switch: determines how the subwoofer will turn on and off:
• When this switch is set in the “Auto” position and the Power switch
is set to “On,” the subwoofer will automatically turn on when it first
detects an audio signal at any of its inputs, and will automatically
enter the standby mode after it has received no audio signal for ten
(10) minutes.
• When this switch is set in the “On” position, the subwoofer will turn
on when the Power switch is set to “On” and will remain on until the
Power switch is set to “Off.”
• When this switch is set in the “Trigger” position and the Power switch
is set to “On,” the subwoofer will automatically turn on when a voltage
is present at the 12V Trigger In connection and will remain on as long
as the voltage is present. When the voltage at the 12V Trigger In
connection is removed the subwoofer will automatically turn off.
Power Mode indicator: The LED glows green when the power switch
is set to On and there is signal at the input and/or a 12V trigger present. If
the power switch is set to On but there is no signal after ten (10) minutes or
there is no trigger voltage, then the LED will glow red. It will be unlit if the
power switch is set to Off or the unit is receiving no power.
Power switch: When this switch is set to “On,” the subwoofer’s on/off
status is dependent on the setting of the Power Mode switch (see above).
When the Power switch is set to “Off” the subwoofer is turned off and
cannot turn on automatically.
We suggest setting the Power switch in the “Off” position if you will not be
using the subwoofer for a long period of time, such as when you’re on vacation.
Power Cord connector: Plug the supplied power cord into this connector
and into a working AC power outlet.unswitched
Power Switch
Power Cord Connector
Power Mode Switch
PEQ Level Control
Input Connectors (Balanced XLR)
Input Connectors (Unbalanced RCA)
Subwoofer Gain (Volume) Control
Low Pass Crossover Frequency Control
PEQ Frequency Control
PEQ Bandwidth Control
Power Indicator LED
Phase
EQ On/Off
EQ Extended
12V Trigger In/Out Connection

Especificaciones del producto

Marca: Revel
Categoría: Altavoz de subgraves
Modelo: Performa3 B110v2

¿Necesitas ayuda?

Si necesitas ayuda con Revel Performa3 B110v2 haz una pregunta a continuación y otros usuarios te responderán


Altavoz de subgraves Revel Manuales

Revel

Revel Performa3 B112v2 Manual de Usario

10 Septiembre 2024
Revel

Revel Performa3 B110v2 Manual de Usario

10 Septiembre 2024

Altavoz de subgraves Manuales

Últimos Altavoz de subgraves Manuales

Canton

Canton SUB 8.2 Manual de Usario

27 Octubre 2024
Deaf Bonce

Deaf Bonce Machete MFX30D2 Manual de Usario

26 Octubre 2024
Phoenix Gold

Phoenix Gold ZP12D4 Manual de Usario

21 Octubre 2024
Phoenix Gold

Phoenix Gold ZP12D2 Manual de Usario

21 Octubre 2024
Phoenix Gold

Phoenix Gold Z12AB Manual de Usario

21 Octubre 2024
Phoenix Gold

Phoenix Gold Z10AB Manual de Usario

21 Octubre 2024
Phoenix Gold

Phoenix Gold ZB8P Manual de Usario

21 Octubre 2024
Bowers And Wilkins

Bowers And Wilkins CT 8SW Manual de Usario

20 Octubre 2024
Pioneer

Pioneer TS-W257D2 Manual de Usario

17 Octubre 2024
Vonyx

Vonyx SWP15 Manual de Usario

17 Octubre 2024