Ruwido Linum 8 Manual de Usario

Ruwido Mando a distancia Linum 8

Lee a continuación 📖 el manual en español para Ruwido Linum 8 (13 páginas) en la categoría Mando a distancia. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/13

Index

GB USER MANUAL 2 - 5

BEDIENUNGSANLEITUNG 6 - 9

ISTRUZIONI PER L’USO 10 - 13

MODE D’EMPLOI 14 - 17

GEBRUIKSAANWIJZING 18 - 21

Easy programming for the control of your CD PLAYER (not for 5 in

1 model)

To programme the remote control to operate your CD PLAYER, proceed as described for the

television set. Complete steps 1 to 10 except you must first press and release the key

followed by holding down the key. Please ensure that you refer to the codes listed under

the CD section and not the TV section.

Easy programming for the control of your TUNER (RADIO) (not for

5 in 1 model)

To programme the remote control to operate your TUNER, proceed as described for the CD

PLAYER but using the key instead of the CD key. Please ensure that you refer to the

codes listed under the TUNER section and not the CD PLAYER section.

Easy programming for the control of your TAPE RECORDER (TAPE

DESK) (not for 5 in 1 model)

To programme the remote control to operate your TAPE RECORDER, proceed as described for

the CD PLAYER but using the key instead of the CD key. Please ensure that you refer to

the codes listed under the TAPE section and not the CD PLAYER section.

Easy programming for the control of your AMPLIFIER (not for 5 in

1 model)

To programme the remote control to operate your AMPLIFIER, proceed as described for the

CD PLAYER. Complete steps 1 to 10, using the key on your remote control. Please ensure

that you refer to the codes listed under the AMPLIFIER section and not CD PLAYER section.

Code scan

If programming using the codes in the enclosed list failed to work then you must next try the

automatic code scan.

A. Ensure that the remote control is equipped with 2 new batteries (see step one of easy

programming procedure).

B. Switch on your TV SET. When using the automatic scan function for the VCR, DVD, CD or

TAPE, switch on your device, insert a video tape, DVD, CD or tape cassette and put the unit

into ‘Play mode’ i.e, the VCR tape etc is running.

C. Press the key of your remote control for approx. 4 seconds until the LED flashes twice.

D. After seeing the 2 flashes and within 5 seconds, enter the code . After entering the

code the LED will flash twice indicating that the code has been accepted

E. Press and hold the key until your TV switches off. Please note that this process might

take up to 15 minutes. During the automatic scanning you can remove your finger or

change hands provided it is replaced within 8 seconds. If left off of the key for more than 8

seconds then the remote will revert back to its normal mode. If your TV switches into

Stand-By mode during the automatic process then immediately remove your finger from

the key and then press the key until the LED flashes twice, this will then store the

code that the remote control has found.

F. In some cases during the automatic scanning search the remote control might find several

codes that appear to operate your TV etc, however, if some of the buttons fail to work

properly then it’s possible the remote has found a partially compatible code. In such cases

you will need to restart the automatic scanning process (steps B. to F.) until a better code is

found. Please note that once the automatic process is restarted, the remote continues from

the last stored code and not at the beginning of code database.

• To complete a code scan for the VCR, DVD, CD or TAPE, follow the procedure above but

use the key and not the key

• To complete a code scan for the TUNER, follow the procedure above but use the key

AMP

TAPE

TUNER

SHIFT

UNIVERSAL REMOTE CONTROL

Thank you for purchasing this universal remote control. Before using the remote you will need

to insert two type "CR2025" batteries (for all Linum models) or two AAA "LR03" batteries (for

AlveusLux 10 and 5 in 1 models) in the battery compartment ensuring that you follow the

polarity shown on the inside. You can now use your remote control to operate up to 10 different

devices including a TV, video recorder, DVD player, satellite or cable receiver, CD player, tuner

(radio), tape recorder and amplifier. If your remote control is equipped with an AUX key then

you can also use it to control a second TV set, video recorded, satellite receiver and/or cable

box, CD player, tuner, tape recorder or amplifier!

Easy programming for the control of your TV SET

1. Insert 2 new batteries of type "CR2025" or "AAA/LR03" (depending on your model).

Observe battery polarity as indicated in the battery compartment.

2. Switch on your TV SET.

3. In the enclosed code list, find your TV brand or manufacturer (e.g. Sony).

4. Beside the manufacturer's name, you will find one or more 3-digit codes. These codes

must be entered into the remote to enable it to work with your particular TV set.

5. Press the key on the remote control for approximately 4 seconds until the LED flashes

twice.

6. After seeing the 2 flashes and within 5 seconds, enter the 3-digit numerical code from the

list.

7. After entering the code the LED will flash twice indicating that the code has been accepted.

8. Point the remote control towards your TV and press the key. If your TV does not

respond by going into Stand-By mode then repeat steps 3 to 8 and enter the next code in

the list.

9. If your TV goes into Stand-By mode when the key pressed then your remote control

has found a compatible code. Next test all of the other function buttons. If certain functions

are not working correctly then restart the process moving onto the next code number as

this may well improve the situation.

10. If the codes in the list fail to operate your TV then next move onto the automatic code scan

function (see below).

Easy programming for the control of your VIDEO RECORDER

To programme the remote control to operate your VIDEO RECORDER, proceed as described

above for the television set. Complete steps 1 to 10 using the key on your remote control.

Please ensure that you refer to the codes listed under the VIDEO RECORDER section and not

the TV section.

Easy programming for the control of your SATELLITE RECEIVER

To programme the remote control to operate your SATELLITE RECEIVER or CABLE BOX,

proceed as described for the television set. Complete steps 1 to 10 using the key on your

remote control. Please ensure that you refer to the codes listed under the SATELLITE section

and not the TV section.

Easy programming for the control of your DVD PLAYER

To programme the remote control to operate your DVD PLAYER, proceed as described for the

television set. Complete steps 1 to 10 using the key on your remote control. Please ensure

that you refer to the codes listed under the DVD section and not the TV section.

DVD

SAT

VCR

USER MANUAL

GB USER MANUAL

Code scan for VCR, SAT, DVD, CD, TAPE, TUNER and AMP

To complete a code scan for VCR, SAT, DVD, CD, TAPE, TUNER or AMP, proceed as described

for a TV code scan. Complete above steps A to G, using keys / or , or

and / and / and or and respectively.

At step E,

for SAT and AMP, press the key;

for VCR, DVD, CD and TAPE, press the key, and

for TUNER, press key .

Finding out what code number you are using

If you have programmed your remote control by means of the automatic code scan, or if you

have forgot the code you have stored then the following procedure will replay the codes being

used.

A. Press the key of your remote control for approx. 4 seconds until the LED flashes twice.

B. Enter code , using the numerical keys. The LED flashes twice.

C. Press key and count the number of LED flashes. This number corresponds to the first

digit of the code.

D. Press key and count the number of LED flashes. This number corresponds to the

second digit of the code (if the digit is 0, the LED does not flash).

E. Press key and count the number of LED flashes. This number corresponds to the third

digit of the code (if the digit is 0, the LED does not flash).

F. Steps C, D and E can be repeated as often as necessary.

To read the currently used code for the control of a VCR, SAT, DVD/AUX, CD, TAPE, TUNER or

AMP device, proceed as described above for your TV SET. Complete steps A to F, pressing the

, , , , , or key respectively.

Write down the code number as indicated by the LED.

Programming for AUX devices

Depending on the model, you can use your universal remote control to operate a second TV

set, video recorder, satellite receiver/cable box, CD player, tape recorder, tuner or amplifier. To

program your remote control for a second device, proceed as follows:

1. Press the key of your remote control until the LED flashes twice.

2. Press

key for a second TV set,

key for a second video recorder,

key for a second satellite receiver or cable box,

keys and for a second CD player,

keys and for a second tape recorder,

keys and for a second tuner,

keys and for a second amplifier.

3. On the numerical keypad, enter a 3-digit code from the enclosed list.

4. The LED flashes twice, indicating that the code has been accepted.

AMP

SHIFT

TUNER

SHIFT

TAPE

SHIFT

SAT

VCR

AUX

AMP

TUNER

TAPE

DVD

SAT

VCR

AMP

SHIFT

TUNER

SHIFT

TAPE

SHIFT

DVD

SAT

VCR

Special functions of your remote control

Brightness / Colour / Contrast / etc.

Adjusting brightness / colour / contrast / bass / tremble / balance at your TV set, using the

universal remote control:

1. Ensure that your remote control is set to TV (press key).

2. Press the key.

3. Within 5 seconds, press

for brightness, for colour,

for contrast, for tremble,

for bass, for balance.

4. To adjust the settings use the and keys.

5. After 5 seconds, your remote control returns to standard mode for the selection of

channels.

Please write down the 3-digit codes of your devices for future reference. Depending on

the remote control model, you might have to reprogram me the universal control device

after a battery change.

VOL-

VOL+

SHIFT

USER MANUAL

GB USER MANUAL

VCR

SAT/CABLE

DVD/AUX

TAPE

TUNER

AMPLIFIER

Especificaciones del producto

Marca:	Ruwido
Categoría:	Mando a distancia
Modelo:	Linum 8

¿Necesitas ayuda?

Si necesitas ayuda con Ruwido Linum 8 haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

Mando a distancia Ruwido Manuales

Ruwido Linum 8 Manual de Usario

19 Septiembre 2024

Ruwido Univeral Manual de Usario

16 Septiembre 2024

Ruwido RC 12110 Manual de Usario

16 Septiembre 2024

Ruwido Alveus Linum 10 Manual de Usario

16 Septiembre 2024

Ruwido Alveus Linum 8 Manual de Usario

16 Septiembre 2024

Ruwido Easytip S2 Manual de Usario

16 Septiembre 2024

Ruwido Easytip S3 Manual de Usario

16 Septiembre 2024

Ruwido Alveus series Manual de Usario

3 Septiembre 2024

Ruwido z 3 easytip Manual de Usario

26 Agosto 2024

Mando a distancia Manuales

Últimos Mando a distancia Manuales

Monacor DRM-880WP Manual de Usario

27 Octubre 2024

Hama Spot-Pointer V2 Manual de Usario

26 Octubre 2024

Sony RM-ED022 Manual de Usario

21 Octubre 2024

Sonos Control Manual de Usario

18 Octubre 2024

One For All URC 7935 Manual de Usario

18 Octubre 2024

Canon BG-E20 Manual de Usario

12 Octubre 2024

Neewer RT112 Manual de Usario

8 Octubre 2024

Neewer RT113 Manual de Usario

8 Octubre 2024

Logitech Harmony 785 Manual de Usario

8 Octubre 2024

DSC WS4949 Manual de Usario

8 Octubre 2024