Saris Cycle-On Pro Manual de Usario

Saris Portabicicletas Cycle-On Pro

Lee a continuación 📖 el manual en español para Saris Cycle-On Pro (4 páginas) en la categoría Portabicicletas. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/4

20" wheel

tray mount

Standard wheel

tray mount

USER MANUAL

-O

Please READ and FOLLOW all instructions carefully.

4017 (1 1/4” RECEIVER) OR 4018 (2” RECEIVER)

ASSEMBLE FRONT WHEEL TRAYS - Determine which holes you

will use to mount the front wheel trays (Fig. 1A). For 20” tires inner-

most holes must be used(20” tire bikes cannot be mounted on the

#4012 add on kit).

Tube

Bolt

Front Wheel

Tray

Washer

Nut

Insert bolt through tube, slide wheel tray on, fasten with washer

and nut (Fig. 1B). Tighten nut until it is snug, where wheel tray

pivots freely. Repeat for each of the 2 front wheel trays.

Next attach the rack to the tilt bracket. Assemble in stepped

order (step 1, 2, 3) as shown above. Tighten knob at end of

bracket until bracket is tight in receiver.

Insert plugs into

unused holes.

1A 1B

MUST use 2 wheel trays per wheel.

See Picture 4B.

Front Wheel

Tray

Washer

Nut

Bolt

Tube

Insert hitch pin and lock into place as shown above. (Note:

Do not stick locking cable through hole, only hitch pin.)

Steel Pin

Pin with

Lanyard Knob

12-15”

Depress the rear wheel clamp lever, and rotate to open position.

Upright Arm

Press

Rotate

Open

Position

Push button on upright arm and rotate arm away from

center of rack.

Set bike into trays. Front wheel should be set into the front wheel

trays. Extend and rotate upright arm to vertical position. Push down

on upright arm to contact top of wheel's front tire. Once contact is

achieved, press down on upright arm for additional "clicks", until

wheel is held securely.

Rotate wheel so the largest gap is centered under wheel hub.

Align rear wheel clamp with largest gap in spokes of rear wheel.

Rotate clamp between spokes closing onto rear wheel tray.

Front Wheel Trays

Upright Arm

(vertical position)

Push

***Note: For bicycles with odd rims or 40 spoke or greater

wheels, additional straps (available through Saris) should

be used in replace of the rear wheel clamp. Thread strap

into rear wheel tray slots and secure bicycle.

***Note: Bicycles with 20” wheels should be loaded

closest to vehicle.

Press

Rotate

Closed

Position

Removal of Bicycles: Reverse instructions 3-5 to

remove bicycle from rack.

Check clearance. It is the responsi-

bility of the user to ensure the nec-

essary clearance (dependent on

vehicle, load, driving territory, etc.) is

given from load to ground.

Generally, 12-15” is adequate. Load

smallest bicycle closest to the

vehicle. Lock bikes to rack with

locking cable provided. Lock must

pass through bikes and rack for total

security.

Slide arm

into base

Always stow arms in this position.

Push

Rotate

Pull cotter pin from clevis pin, remove clevis pin.

Note: Rack arms must be in stowed position

Remove clevis pin

Rotate rack up to stop position, insert pin into lower hole,

and insert cotter pin into clevis pin. Rack is now stowed.

STOWED POSTION

Rotate rack and

replace clevis pin

Especificaciones del producto

Marca:	Saris
Categoría:	Portabicicletas
Modelo:	Cycle-On Pro
Peso.:	10 g
Peso del embalaje:	170 g
Tecnología de conectividad:	Bedraad
Conexiones:	2 - DB9 Male
Sistemas operativos compatibles:	Windows 2000/XP & Server 2003
Interfaz de host:	PCIe
Dimensiones (Ancho x Fondo x Alto):	92 x 120 mm
Número de puertos:	2