Shure SBC850 Manual de Usario

Shure cargador de bateria SBC850

Lee a continuación 📖 el manual en español para Shure SBC850 (6 páginas) en la categoría cargador de bateria. Esta guía fue útil para 8 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/6

IMPORTANT SAFETY INSTRUCTIONS

1. READ these instructions.

2. KEEP these instructions.

3. HEED all warnings.

4. FOLLOW all instructions.

5. DO NOT use this apparatus near water.

6. CLEAN ONLY with dry cloth.

7. DO NOT block any ventilation openings. Allow sufficient distances for

adequate ventilation and install in accordance with the manufacturer’s

instructions.

8. DO NOT install near any heat sources such as open flames, radiators,

heat registers, stoves, or other apparatus (including amplifiers) that pro-

duce heat. Do not place any open flame sources on the product.

9. DO NOT defeat the safety purpose of the polarized or grounding type

plug. A polarized plug has two blades with one wider than the other. A

grounding type plug has two blades and a third grounding prong. The

wider blade or the third prong are provided for your safety. If the provided

plug does not fit into your outlet, consult an electrician for replacement

of the obsolete outlet.

10. PROTECT the power cord from being walked on or pinched, particularly

at plugs, convenience receptacles, and the point where they exit from

the apparatus.

11. ONLY USE attachments/accessories specified by the manufacturer.

12. USE only with a cart, stand, tripod, bracket, or table specified by the

manufacturer, or sold with the apparatus. When a cart is used, use caution

when moving the cart/apparatus combination to avoid injury from tip-over.

13. UNPLUG this apparatus during lightning storms or when unused for long

periods of time.

14. REFER all servicing to qualified service personnel. Servicing is required

when the apparatus has been damaged in any way, such as power

supply cord or plug is damaged, liquid has been spilled or objects have

fallen into the apparatus, the apparatus has been exposed to rain or

moisture, does not operate normally, or has been dropped.

15. DO NOT expose the apparatus to dripping and splashing. DO NOT put

objects filled with liquids, such as vases, on the apparatus.

16. The MAINS plug or an appliance coupler shall remain readily operable.

17. The airborne noise of the Apparatus does not exceed 70dB (A).

18. Apparatus with CLASS I construction shall be connected to a MAINS

socket outlet with a protective earthing connection.

19. To reduce the risk of fire or electric shock, do not expose this apparatus

to rain or moisture.

20. Do not attempt to modify this product. Doing so could result in personal

injury and/or product failure.

21. Operate this product within its specified operating temperature range.

Explanation of Symbols

Caution: risk of electric shock

Caution: risk of danger (See note.)

Direct current

Alternating current

On (Supply)

Equipment protected throughout by DOUBLE INSULATION or

REINFORCED INSULATION

Stand-by

Equipment should not be disposed of in the normal waste stream

WARNING: Voltages in this equipment are hazardous to life. No user-ser-

viceable parts inside. Refer all servicing to qualified service personnel. The

safety certifications do not apply when the operating voltage is changed from

the factory setting.

General Description

SBC450 and SBC850 networked docking stations provide monitoring, control,

and power to charge 4 or 8 ULXD6 and ULXD8 transmitters with Shure

rechargeable batteries. Connect to a network to adjust transmitter settings

and monitor rechargeable batteries using Shure Wireless Workbench

®or

SystemOn software, or through a third-party room control system.

Features

• Compatible with ULXD6 and ULXD8 transmitters using Shure recharge-

able batteries

• Easily adjust transmitter settings using Shure control software such as

Wireless Workbench and external control systems such as AMX or Cre-

stron

• Monitor rechargeable battery information such as health, temperature,

charge, and cycle using control software

• Update transmitter and docking station firmware using Shure Update

Utility

Included Components

• PS60 power supply (some models available without power supply)

SBC450 SBC850

4- and 8-Bay Networked Docking Stations

More Information Available Online

A comprehensive online user guide is available at .pubs.shure.com

Controls and Connectors

௟

௠

௡

௢

௤

௣

௥

௢

௦ ௧

① Power Button

Press to turn on; press and hold to turn off.

② Reset Button

• Press and hold reset button while simultaneously powering on the docking station to restore factory settings. IP addressing will beDocking station reset:

reset to Automatic. LEDs = solid green.

•Transmitter reset: Place transmitters in docks. Press and hold reset button for 5 seconds to restore transmitter factory settings. Transmitter mute LEDs =

flashing.

③ Power LED

• On = Docking station is on

• Off = Docking station is off

④ Ethernet Port

Connect to an Ethernet network to enable remote device control and monitoring using Wireless Workbench or other control software.

⑤ Power Input

Connect to power supply.

⑥ Battery Status LEDs

Each slot has 5 LEDs that illuminate to show the battery's charge level:

% Battery ChargeLED

1•Flashing: <10%

•Solid: >10%

>25%2

>50%3

>75%4

100%5

⑦ Docking Slots (USB 3.0)

Slide any ULXD6 or ULXD8 transmitter with a Shure rechargeable battery into a slot to begin charging.

Shure IncorporatedSBC450 SBC850 4- and 8-Bay Networked Docking Stations

2017/11/272/6

⑧ Ethernet Link Speed LED (Amber)

• Off = 10 Mbps

• On = 100 Mbps

⑨ Ethernet Status LED (Green)

• Off = No network link

• On = Network link established

• Flashing = Network link active

Power Connections

1. Connect power supply to a power outlet and to the docking station power

input.

2. The docking station automatically turns on when connected to power.

Press and hold power button to turn off.

If the docking station loses power, transmitters will also power off.

Connecting Transmitters

Insert a ULXD6 or ULXD8 transmitter with Shure rechargeable batteries into

the slot as shown:

The docking station provides power to charge transmitter batteries:

• 15 minutes = 1 hour of use

• 1 hour = 50% charged

• 3 hours = 100% charged

Note: If the docking station loses power, transmitters will also power off.

Batteries will resume charging when power is restored.

Connecting Shure Devices to Wireless Workbench

Wireless Workbench lets you control and monitor devices over the network. To get started, visit and download Wireless Workbenchhttp://www.shure.com/wwb

software. Wireless Workbench communicates with connected devices over a standard Ethernet network.

Required equipment: Shure device, computer with Wireless Workbench installed, Cat 5 (or better) Ethernet cable, and router or network switch

1. Connect the device to your computer with a shielded Cat 5 (or better) Ethernet cable to ensure reliable network performance. If you have multiple devices

to manage, connect each device to a router or network switch. The Ethernet port LEDs on your device will illuminate to indicate network connectivity. Verify

that Shure devices can see each other by looking for the network connectivity icon on the front panel (location varies).

2. For most applications, use the Automatic mode (default) to let your switch or router assign an IP address using DHCP addressing. If no DHCP server is

present, your devices will fall back to a link-local address in the 169.254.xxx.xxx range. If you need to assign specific IP addresses, set the IP mode to