SIIG CE-MT0212-S1 Manual de Usario

SIIG Wandsteun CE-MT0212-S1

Lee a continuación 📖 el manual en español para SIIG CE-MT0212-S1 (8 páginas) en la categoría Wandsteun. Esta guía fue útil para 5 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/8
Caution
A B C D E F G
04-0527C
Full-Motion LCD/TV Monitor Mount - 10" to 24"
Installation Instructions
(x2) M6X60
bolt
(x2) M6 concrete
anchor
(x4) M6 small
washer
(x2) M6 large
washer
(x4) M4X12
screw
(x4) M5X12
screw
Tools Required: Electronic stud finder, #2 Phillips head screw driver, drill, 1/8" drill bit (wood stud installation), 5/16" masonry
drill bit (concrete/brick wall installation).
Do not install near heater, fireplace, air conditioning, in direct sunlight, or any other heat producing source.
Failure to do so may result in damage to the display and could increase the risk of fire.
The wall structure must be capable of supporting at least the maximum load capacity as indicated. If not, the
wall must be reinforced. Proper installation procedure by yourself or a qualified service technician, as outlined in
the installation instructions, must be adhered to. Failure to do so could result in serious personal injury.
When mounting to a wall that contains wood studs, confirm dead center of the wood stud prior to installation, it
is recommended that the wood studs be a minimum of 16" apart.
It is recommended that two people perform the installation. Injury and/or damage can result from dropping or
mishandling the display.
(x4) M6X12
screw
Prior to the installation of this product, the installation instructions should be read and completely understood.
The installation instructions must be read to prevent personal injury and property damage. Keep these
installation instructions in an easily accessible location for future reference.
CAUTION: The maximum load capacity is 33 lbs (15kg). Use with products exceeding the maximum load
capacity may cause serious injury. See apparatus instructions.
Recommended mounting surfaces: wood stud and solid-flat concrete. If the mount is to be installed on any
surface other than wood studs, use suitable hardware (not included but commercially available) .
Hardware Kit
Do not install on a structure that is prone to vibration, movement or chance of impact. Failure to do so could
result in damage to the display and/or damage to the mounting surface.
1
1
2
3
4
1
2
3
1
2
Take down the plate and drill two 2" deep holes, using a 1/8" drill bi
t
at the position you'v
e
marked.
Hold the wall plate to the wall, use the two mounting holes to mark the locations to be used for
mounting the wall plate.
Step 2: Display Plate Installation
Position the wall plate onto the wall again and insert the bolts (A) and washer (D) into the
anchor as shown (figure 1-c) and tighten.
Place your TV screen down on a soft, flat surface, and locate the threaded mounting points
that are located on the back of the display.
Attach the wall plate to the wall again and insert the bolts (A) and washers (D) into the holes
and tighten (figure 1-b).
Use a high-quality electronic stud finder (commercially available) to locate dead center of a
stud and mark the location with a pencil (figure 1-a).
Hold the wall plate (figure 1-c) to the wall, use the two mounting holes to mark the locations to
be used for mounting the wall plate. Locate the holes directly into the brick, block or concrete,
never into the mortar between the blocks.
Step 1: Wall Plate Installation
Wood Stud Installation
Pre-drill two holes to a depth of 2" using a 3/8" masonry drill bit at the positions you've marked
and insert one concrete anchor (B) into each hole.
According to the size of the display's hole, choose the corresponding screw (E/F/G) and
washer (C) and insert into the hole as shown (figure 2-a) and tighten.
Concrete/Brick Wall Installation
2
1
2
3
4Insert the cables from your LCD TV/Monitor through the
cable ties (figure 3-c).
Step 3: Final Installation
When tilting the display, first loosen the knob and then tilt
the plate to the desired position. Re-tighten the knob to
secure the display.
Tighten the screw at the bottom of the display plate to
secure (figure 3-b).
Hang the display plate onto the top of the wall plate and
slip it into the wall plate as shown (figure 3-a).
IMPORTANT: If you don't understand the installation instructions, please consult an installation
specialist.
Maintenance
Check the mounting screws every two months for tightness.
3

Especificaciones del producto

Marca: SIIG
Categoría: Wandsteun
Modelo: CE-MT0212-S1

¿Necesitas ayuda?

Si necesitas ayuda con SIIG CE-MT0212-S1 haz una pregunta a continuación y otros usuarios te responderán




Wandsteun SIIG Manuales

Wandsteun Manuales

Últimos Wandsteun Manuales