SIIG CE-MT0812-S1 Manual de Usario

SIIG Wandsteun CE-MT0812-S1

Lee a continuación 📖 el manual en español para SIIG CE-MT0812-S1 (8 páginas) en la categoría Wandsteun. Esta guía fue útil para 5 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/8

04-0541A

TV Size: 32" - 55”

Max load capacity: 121lbs/55kg

Wall distance: 0.43/11mm

Universal Mounting Pattern

Ultra-Thin LED/LCD TV Mount - 32" to 55"

IMPORTANT: If you don't understand the installation instructions, please consult an

installation specialist

Ultra-Thin LED/LCD TV Wall Mount

Material: 2.0mm Cold Rolled Steel Plate

Installation Instructions

Caution

A G

B H

C I

D J

E K

F L

(×4) M8×16 screw

(×4) M6×16 screw

(×4) M8×80 bolt

(×4) M5×35 screw (×4) Concrete anchor

(×4) M8×35 screw (x2) Sponge sticker

(×4) M6×35 screw (×4) M8 spacer

When mounting to a wall that contains wood studs, confirm dead center of the wood stud prior to installation, it is

recommended that the wood studs be a minimum of 16" apart.

It is recommended that two people perform the installation. Injury and/or damage can result from dropping or

mishandling the display.

INSTALLATION AND OPERATING INSTRUCTIONS

Do not install near heater, fireplace, air conditioning, in direct sunlight, or any other heat producing source.

Failure to do so may result in damage to the display and could increase the risk of fire.

The wall structure must be capable of supporting at least the maximum load capacity as indicated. If not, the

wall must be reinforced. Proper installation procedure by yourself or a qualified service technician, as outlined in

the installation instructions, must be adhered to. Failure to do so could result in serious personal injury.

Recommended mounting surfaces: wood stud and solid-flat concrete. If the mount is to be installed on any

surface other than wood studs or concrete, use suitable hardware (not included but commercially available).

Prior to the installation of this product, the installation instructions should be read and completely understood.

The installation instructions must be read to prevent personal injury and property damage. Keep these

installation instructions in an easily accessible location for future reference.

CAUTION: The maximum load capacity is 121 lbs. Use with products exceeding the maximum load capacity may

cause serious injury. See apparatus instructions.

Do not install on a structure that is prone to vibration, movement or chance of impact. Failure to do so could

result in damage to the display and/or damage to the mounting surface.

Hardware Kit

(×4) M5×16 screw (×4) M6 washer

(x4) M5 washer

a) Wood Stud Installation

You should mark two positions total.

Stud finder for drywall installation

NOTE: When mounting to wood studs, the two wood studs must be a minimum of 16" apart.

Use a high-quality electronic stud finder (commercially available) to locate dead center of two studs and mark

their locations with a pencil.

Step 1: Wall Plate Installation

2With the help of an assistant, and using a bubble level to ensure the wall plate is level, position the wall plate

against the wall in the desired mounting location.

Mark the right and the left positions of the small horizontal slots that are in alignment with the studs.

Tools Required

Phillips head screw driver

Tighten the bolt with the 1/2" socket or 1/2" open-end wrench by turning clockwise until tight.

For each location, insert bolt (I) into the wall.

Pre-drill a 3/16" hole to a depth of approximately 3" in the wall stud at each marked location.

Level

1/2" socket & socket wrench and/or 1/2" open-end wrench

Drill, 3/16" (5mm) drill bit for wood stud installation and 3/8" (10mm) masonry drill bit for concrete/brick installation

CAUTION: Do not release the wall plate until it is properly mounted and secured to the wall.

6Place the wall plate against the wall and line up the mounting slots with the drilled holes. Check the bubble level

to verify that the wall plate is level.

CAUTION: Do not over-tighten bolts - doing so may cause unnecessary damage to the wall.

Especificaciones del producto

Marca:	SIIG
Categoría:	Wandsteun
Modelo:	CE-MT0812-S1
Color del producto:	Groen
Peso.:	56 g
Ancho:	63 mm
Profundidad:	75 mm
Altura:	15 mm
Peso del embalaje:	136 g
Ancho del embalaje:	170 mm
Empaquetadura en profundidad:	142 mm
Altura del embalaje:	30 mm
Tipo de conexión en serie:	RS-232
Certificados de sostenibilidad:	CE, RoHS
Número:	1
Temperatura de almacenamiento:	-20 - 100 °C
Interno:	Ja
Cumplimiento de la sostenibilidad:	Ja
Compatible con Linux:	Ja
Guía de Instalación Rápida:	Ja
Tiempo medio entre fallos (MTBF):	222366 uur
Interfaz de host:	PCIe
Sistemas operativos de servidor compatibles:	Windows Server 2003, Windows Server 2008 R2, Windows Server 2012, Windows Server 2012 R2, Windows Server 2016
Puertos seriales):	2
conjunto de chips:	Asix AX99100
Altura del paquete principal (exterior):	306 mm
Ancho del embalaje principal (exterior):	685 mm
Longitud del paquete principal (exterior):	345 mm
Cantidad por caja principal (exterior):	75 stuk(s)
Temperatura de funcionamiento (TT):	-10 - 80 °C
Humedad relativa de funcionamiento (VV):	5 - 85 procent
Código del Sistema Armonizado (SA):	84733020
Estándar de tarjeta de expansión:	PCIe 1.1
FIFO (primero en entrar, primero en salir):	256 B
Interfaz de salida:	Serie
Velocidad en baudios:	921.6 Kbit/s
Bits de datos:	5, 6,7, 8,9
Bits de parada:	1, 1.5, 2
bit de paridad:	Even, Mark, N,Odd, Space
Tipo de control de flujo:	N, RTS/CTS, XON/XOFF