Soundskins SSK-BRONCO Manual de Usario

Soundskins No categorizado SSK-BRONCO

Lee a continuación 📖 el manual en español para Soundskins SSK-BRONCO (5 páginas) en la categoría No categorizado. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/5
Bronco Kit Installation Instructions
1. Start by locating the fastening hardware on the door panels.
There will be one behind the door handle under a plastic cover,
one behind the door grab handle that you will have to pop out to
reveal, and 2 at the bottom right corner of the door panels. Take a
7 mm socket and remove. Then, use a panel tool to pry the panel
off the door, start from the bottom right corner. Be sure not to break
any clips or mounting hardware.
3. Then, start applying the door pieces. Peel off the backing paper
starting at the top, tack the piece onto the door and work your way
down, pressing down the material and pulling down the backing
paper more as you go along. Remember to feed the harnesses
through the proper holes and ensure all holes are aligned properly
before pressing the entire piece down. Repeat steps 1-3 for all 4
doors.
4. Before removing the front seats, you MUST disconnect the
negative terminal of your car battery with a 10 mm bolt. Now, you
can work on removing the front seats. There are 13 mm bolts
covered by plastic cover plates on both sides underneath the seats
- you will need a T20 torx bit to remove them. Then, disconnect the
harness by sliding the red security tab out of the way and pinching
the connector. Then, carry the seats out of the car.
2. Pull the door panel away slowly. There will be 2 plug clips that
will need to be released as well as a wire plug to disconnect. Set
the door panel aside and unhook all plugs, remove the vapor
barrier, and clean the car metal surface using a microfiber cloth
and Acetone or other cleaning solution. The point is to get the
surface clean to ensure material glue contact.
• Drill
• 7mm, 10 mm, 13mm, 18mm socket
• Socket extension
• T20, T30, T55 torx bit
• Panel/trim tool
• Roller
• Flat head screw driver
• 3/8” Ratchet
• Microber cloth
• Acetone or cleaning solution
• Shop vacuum
• Tarp, cloth, blanket, or towel
Tools needed for installation:
R
Scan this code to watch the
full instructional video!
8. Insert a trim tool between the selector lever boot and the trim
ring to release the tabs and lift the boot upwards. Then,
disconnect all the plugs in the center console.
5. The next step is to take apart the center console. Remove the
trim panel underneath the dash stereo - it will snap outward.
7. Then, remove the center console main top piece. It will
unsnap through the seam area as seen in the photo to the left.
6. Next, remove the grip handle on the center console on the
passenger side that is held by 2 T30 bolts.
9. There will be a black plastic keeper crossing over the top of
the center console held by 7 mm bolts. Remove this piece.
13. Go back to the door cabin and remove the door seals on each
door. Then, in the driver seat floor section, remove the kick panel
on the left foot rest using an extension and 10mm tool. Pull out the
bolts and remove this kick panel (shown in the photo to the left).
12. Head to the trunk. Remove the trim plate behind the backseats
to reveal some 18 mm bolts (shown in the photo to the left).
Remove the bolts, then remove the backseats. We recommend
taking out the smaller seat first, then bringing the larger one out
after. Disconnect the two plugs in the backseat area.
10. Locate the two 7mm bolts on each side of the center console
covered by plastic keepers. Remove these bolts and take out the
final piece of the center console.
11. Remove the backseats. There will be bolts at the bottom and
nuts in the center of the seats that need to be removed in order to
take the bottom brackets of the seats off. Then, there will be 18 mm
bolts that hold the brackets for the seats and seatbelts, as well as
T55s holding the seatbelts on each side that will need to be
removed.
14. Then, remove the B pillar plastic covers located in between the
front and back doors. They should unsnap easily.

Especificaciones del producto

Marca: Soundskins
Categoría: No categorizado
Modelo: SSK-BRONCO

¿Necesitas ayuda?

Si necesitas ayuda con Soundskins SSK-BRONCO haz una pregunta a continuación y otros usuarios te responderán


No categorizado Soundskins Manuales

Soundskins

Soundskins SSK-GLDTR4DR Manual de Usario

14 Septiembre 2024
Soundskins

Soundskins SSK-RDGLD14 Manual de Usario

14 Septiembre 2024
Soundskins

Soundskins Rings v3 SSK-RINGS Manual de Usario

14 Septiembre 2024
Soundskins

Soundskins SSK-STGLD14 Manual de Usario

14 Septiembre 2024
Soundskins

Soundskins SSK-SEK Manual de Usario

14 Septiembre 2024
Soundskins

Soundskins SSK-F2504DR Manual de Usario

14 Septiembre 2024
Soundskins

Soundskins SSK-RAP4DR Manual de Usario

14 Septiembre 2024
Soundskins

Soundskins SSK-BRONCO Manual de Usario

14 Septiembre 2024
Soundskins

Soundskins Pro Plus SSPROPLUS-1 Manual de Usario

14 Septiembre 2024
Soundskins

Soundskins SSK-TCM4DR Manual de Usario

14 Septiembre 2024

No categorizado Manuales

Últimos No categorizado Manuales

POLARIS

POLARIS RZR S 1000 EPS (2018) Manual de Usario

27 Octubre 2024
Workzone

Workzone 20V Li-Ion Reciprocating Saw PT160501 Manual de Usario

27 Octubre 2024
Philips

Philips 43PUL7672 Manual de Usario

27 Octubre 2024
Manhattan

Manhattan 461504 Manual de Usario

27 Octubre 2024
Sungrow

Sungrow SG125HV Manual de Usario

27 Octubre 2024
Schneider

Schneider CCT724319 Manual de Usario

27 Octubre 2024
Technoline

Technoline WS 250 Manual de Usario

27 Octubre 2024
Livarno

Livarno IAN 354423 Manual de Usario

27 Octubre 2024
Kupper

Kupper 12152 Manual de Usario

27 Octubre 2024
JennAir

JennAir CARBON24L Manual de Usario

27 Octubre 2024