Soundskins SSK-WJLTRUNK Manual de Usario

Lee a continuación 📖 el manual en español para Soundskins SSK-WJLTRUNK (3 páginas) en la categoría No categorizado. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/3
Jeep JL Trunk Kit Instructions
1. Start by unclipping the side panels on your wheel wells.
Begin from the top of the side panels. If you have a factory
subwoofer, remove the torque bolt at the front to unplug the
subwoofer.
Then, remove the main floor piece by sliding it back and up,
and remove the side carpet pieces by removing the 6 clips
that cover the tops of the torque bolts.
2. Next, unclip the flap/panel that sits on the back of the
backseat. It will be tight, so use a clip removal tool or the
back side of a hammer to wedge the clips out. Once this
panel is off, it will reveal the 3 bolts holding down the
backseats of the Jeep.
3. To remove the backseats, you will need an 18mm socket to
remove the bolts. Take out the 2 bolts in the back and the
bolts in front of the backseats. When all bolts are out, remove
the smaller seat first, then the larger seat. Be sure you also
remove the seatbelt bolts. Then, remove the carpet under
the backseat area.
R
Scan this code to watch the
full instructional video!
• Socket tool set & extension
• Panel/trim tool
• Roller
• Clip removal tool
• Screw driver
• Microber cloth
• Acetone or cleaning solution
• Shop vacuum
• Razor blade
Tools needed for installation:
4. Now that your car’s metal surface is exposed in the correct
area, prep the metal surface for application. Use a shop
vacuum if necessary, then use a microfiber cloth and Acetone
(use a breathing mask). Wipe away any moisture, oil, debris,
etc. Then let it air dry for an appropriate amount of time. The
point is to get the surface clean to ensure material glue
contact.
5. Start installing the kit by mocking up the wheel well pieces.
There is a different between the left and right wheel wells, and
you will have to unscrew some plugs on both wheel well
sides. Make sure it lines up correctly before you pull the
backing paper off and start rolling the material down using a
roller. Make sure the material is applied evenly without no air
bubbles. Use a razor blade point or household needle to
release any air pockets.
6. Repeat these steps for all pieces, moving on to the main
trunk floor piece, then the smaller floor pieces. After all pieces
are installed, double check that no holes are blocked for the
mounting hardware and all the material has solid contact.
Last, replace the carpet, seats, and panels and tighten all the
bolts securely.
Soundskins USA
13452 Alondra Blvd, Cerritos, Ca 90703
Phone: 877.211.5597
Email: team@soundskinsglobal.com
www.SoundSkinsGlobal.com
YOU’RE NOW READY TO HIT THE ROAD!
5 Piece Custom Cut PRO KIT
2018+
Recommended Installation Instructions
A. Prepping the Surface
After removing interior door panels, you are ready to clean the metal areas that will be insulated. If the
metal has “new” look without imperfections, then take a microfiber cloth and wipe away any dust and debris.
If the metal is showing signs of age like rust, we recommend using Acetone with a breathing mask to
wipe off debris and loose particles. A shop vacuum might be needed to remove loose debris on the floorboard.
B. Installing Panels
Now that you have a clean surface, you are ready to start applying the sheets. We recommend using a roller to release
air pockets that might be lingering from trapped air. You want to make sure that you have rolled those out to the
edge and all the material has a good seal to the metal surface. Make sure all pieces are installed and inspected
before reinstalling the interior.
1) Main Floor Piece 2) Left Wheel Well Piece 3) Right Wheel Well Piece
4) Bottom Left Floor Piece 5) Bottom Right Floor Piece
1
2 3
4 5

Especificaciones del producto

Marca: Soundskins
Categoría: No categorizado
Modelo: SSK-WJLTRUNK

¿Necesitas ayuda?

Si necesitas ayuda con Soundskins SSK-WJLTRUNK haz una pregunta a continuación y otros usuarios te responderán




No categorizado Soundskins Manuales

No categorizado Manuales

Últimos No categorizado Manuales