Stanley FMC710 Manual de Usario

Stanley máquina de aserrar FMC710

Lee a continuación 📖 el manual en español para Stanley FMC710 (108 páginas) en la categoría máquina de aserrar. Esta guía fue útil para 8 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/108

www.stanley.eu

FMC710

D E

ENGLISH

(Original instructions)

d. Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool or

these instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

e. Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tools

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

5. Battery tool use and care

a. Recharge only with the charger specied by the

manufacturer. A charger that is suitable for one type of

battery pack may create a risk of re when used with

another battery pack.

b. Use power tools only with specically designated

battery packs. Use of any other battery packs may create

a risk of injury and re.

c. When battery pack is not in use, keep it away from

other metal objects, like paper clips, coins, keys,

nails, screws, or other small metal objects, that can

make a connection from one terminal to another.

Shorting the battery terminals together may cause burns

or a re.

d. Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally

occurs, ush with water. If liquid contacts eyes,

additionally seek medical help. Liquid ejected from the

battery may cause irritation or burns.

6. Service

a. Have your power tool serviced by a qualied repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

@Warning! Additional safety warnings for oscil-

lating tools

u Hold power tool by insulated gripping surfaces when

performing an operation where the cutting accessory

may contact hidden wiring. Cutting accessory contacting

a "live" wire may make exposed metal parts of the power

tool "live" and could give the operator an electric shock

u Use clamps or another practical way to secure and

support the workpiece to a stable platform. Holding the

work by hand or against your body leaves it unstable and

may lead to loss of control.

@Warning! Contact with or inhalation of dusts

arising from sanding applications may endanger

the health of the operator and possible bystand-

ers. Wear a dust mask specically designed for

protection against dust and fumes and ensure

that persons within or entering the work area are

also protected.

u Thoroughly remove all dust after sanding.

u Take special care when sanding paint which is possibly

lead based or when sanding some woods and metal which

may produce toxic dust:

t Do not let children or pregnant women enter the work

area.

t Do not eat, drink or smoke in the work area.

t Dispose of dust particles and any other debris safely.

u The intended use is described in this instruction manual.

The use of any accessory or attachment or performance

of any operation with this tool other than those recom-

mended in this instruction manual may present a risk of

personal injury and/or damage to property.

u The accessory will continue to move after releasing the

switch. Always switch the tool off and wait for the acces-

sory to come to a complete standstill before putting the

tool down.

u Keep hands away from cutting area. Never reach

underneath the work piece for any reason. Do not insert

ngers or thumb into the vicinity of the reciprocating blade

and blade clamp. Do not stabilize the saw by gripping the

shoe.

u Keep blades sharp. Dull or damaged blades may cause

the saw to swerve or stall under pressure. Always use the

appropriate type of saw blade for the workpiece material

and type of cut.

u When cutting pipe or conduit, make sure that they are free

from water, electrical wiring, etc.

u Do not touch the workpiece or the blade immediately after

operating the tool. They can become very hot.

u Be aware of hidden hazards, before cutting into walls,

oors or ceilings, check for the location of wiring and

pipes.

ENGLISH (Original instructions)

Safety of others

u This appliance is not intended for use by persons (includ-

ing children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concern-

ing use of the appliance by a person responsible for their

safety.

u Children should be supervised to ensure that they do not

play with the appliance.

Residual risks.

Additional residual risks may arise when using the tool which

may not be included in the enclosed safety warnings. These

risks can arise from misuse, prolonged use etc.

Even with the application of the relevant safety regulations

and the implementation of safety devices, certain residual

risks can not be avoided. These include:

u Injuries caused by touching any rotating/moving parts.

u Injuries caused when changing any parts, blades or ac-

cessories.

u Injuries caused by prolonged use of a tool. When using

any tool for prolonged periods ensure you take regular

breaks.

u Impairment of hearing.

u Health hazards caused by breathing dust developed when

using your tool (example:- working with wood, especially

oak, beech and MDF.)

Vibration

The declared vibration emission values stated in the technical

data and the declaration of conformity have been measured

in accordance with a standard test method provided by

EN 60745 and may be used for comparing one tool with

another. The declared vibration emission value may also be

used in a preliminary assessment of exposure.

Warning! The vibration emission value during actual use of

the power tool can differ from the declared value depending

on the ways in which the tool is used. The vibration level may

increase above the level stated.

When assessing vibration exposure to determine safety

measures required by 2002/44/EC to protect persons regularly

using power tools in employment, an estimation of vibration

exposure should consider, the actual conditions of use and the

way the tool is used, including taking account of all parts of the

operating cycle such as the times when the tool is switched off

and when it is running idle in addition to the trigger time.

Labels on tool

The following pictograms are shown on the tool:

:Warning! To reduce the risk of injury, the user

must read the instruction manual.

Additional safety instructions for batteries and

chargers

Batteries

u Never attempt to open for any reason.

u Do not expose the battery to water.

u Do not store in locations where the temperature may

exceed 40 °C.

u Charge only at ambient temperatures between 10 °C and

40 °C.

u Charge only using the charger provided with the tool.

u When disposing of batteries, follow the instructions given

in the section "Protecting the environment".

pDo not attempt to charge damaged batteries.

Chargers

u Use your Stanley Fat max charger only to charge the bat-

tery in the tool with which it was supplied. Other batteries

could burst, causing personal injury and damage.

u Never attempt to charge non-rechargeable batteries.

u Have defective cords replaced immediately.

u Do not expose the charger to water.

u Do not open the charger.

u Do not probe the charger.

$The charger is intended for indoor use only.

+Read the instruction manual before use.

Electrical safety

#Your charger is double insulated; therefore no

earth wire is required. Always check that the

mains voltage corresponds to the voltage on the

rating plate. Never attempt to replace the charger

unit with a regular mains plug.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Stanley Fat Max Service

Centre in order to avoid a hazard.

ENGLISH

(Original instructions)

Variable speed control (g. I)

The variable speed control allows you to adapt the speed of

the tool to the application.

u Set the variable speed dial (2) to the desired setting. At

setting 1 the tool will operate at low speed, 8,000 min-1.

At setting 6 the tool will operate at the maximum speed,

18,000 min-1.

Switching on and off (g. J)

u To switch the tool on, slide the on/off switch (1) forward

(position I).

u To switch the tool off, slide the on/off switch (1) to the rear

(position O).

LED work light

The LED work light (5) is activated automatically when the tool

is switched on.

Low-battery Indicator

If the LED worklight (5) begins to rapidly and continuously

ash when the switch on the tool is depressed, the battery-

pack power has run out, and the battery pack should be

recharged.

Unlike other battery pack types, Lithium-Ion battery packs

deliver fade-free power for their entire run time. The tool will

not experience a slow, gradual loss of power as you work. To

signal that the battery pack is at the end of its run time and

needs to be charged, the power to the tool will drop quickly.

Note: The LED may also ash due to an overload or high

temperature (see Battery Protection).

Hints for optimum use

u Always hold the tool securely. For precision work, hold the

tool near the front.

u Clamp the workpiece whenever possible, especially when

using cutting blades.

u Do not exert too much pressure on the tool.

u Always use the appropriate type of attachment for the

workpiece material and type of cut.

u Regularly check the condition of accessories. Replace

when necessary.

u Mark the desired starting point.

u Switch the tool on and slowly feed attachments into the

workpiece at the desired starting point.

u Clamp a piece of plywood or soft wood to the back of the

workpiece and saw through the combination in order to

obtain a clear cut.

u Do not force the cutting blade into the workpiece. Note

that cutting sheet metal will normally take more time than

sawing thicker wooden workpieces.

u When cutting metal spread a thin lm of oil along the cut-

ting line before cutting.

u When sanding new layers of paint before applying another

layer, use extra ne grit.

u On very uneven surfaces, or when removing layers of

paint, start with a coarse grit. On other surfaces, start with

a medium grit. In both cases, gradually change to a ne

grit for a smooth nish.

u Consult your retailer for more information on available

accessories.

Maintenance

Your Stanley Fat Max corded/cordless appliance/tool has

been designed to operate over a long period of time with a

minimum of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

Warning! Before performing any maintenance on corded/

cordless power tools:

u Switch off and unplug the appliance/tool.

u Or switch off and remove the battery from the appliance/

tool if the appliance/tool has a separate battery pack.

u Or run the battery down completely if it is integral and then

switch off.

u Regularly clean the ventilation slots in your appliance/tool/

charger using a soft brush or dry cloth.

u Regularly clean the motor housing using a damp cloth. Do

not use any abrasive or solvent-based cleaner.

Mains plug replacement (U.K. & Ireland only)

If a new mains plug needs to be tted:

u Safely dispose of the old plug.

u Connect the brown lead to the live terminal in the new

plug.

u Connect the blue lead to the neutral terminal.

Warning! No connection is to be made to the earth terminal.

Follow the tting instructions supplied with good quality plugs.

Recommended fuse: 5 A.

Protecting the environment

ZSeparate collection. This product must not be

disposed of with normal household waste.

Should you nd one day that your Stanley Fat Max product

needs replacement, or if it is of no further use to you, do not

dispose of it with household waste. Make this product avail-

able for separate collection.

zSeparate collection of used products and packag-

ing allows materials to be recycled and used again.

Re-use of recycled materials helps prevent

environmental pollution and reduces the demand

for raw materials.

Especificaciones del producto

Marca:	Stanley
Categoría:	máquina de aserrar
Modelo:	FMC710
Color del producto:	Wit
Ancho:	197 mm
Altura:	50 mm
Peso del embalaje:	2130 g
Ancho del embalaje:	221 mm
Altura del embalaje:	102 mm
Material de la carcasa:	Aluminium
Número de lámparas:	1 gloeilamp(en)
Tipo de lámpara:	LED
Lámpara de encendido:	13 W
Código de seguridad internacional (IP):	IP20
Diámetro:	1650 mm
Tipo de fuente de energía:	AC
Voltaje de entrada:	220-240 V
Longitud:	273 mm
Tipo de ajuste/pie:	Niet-verwisselbare lamp(en)
Vida útil de la lámpara:	20000 uur
Potencia equivalente de una lámpara incandescente:	65 W
luz de color:	Warm wit
Los activos totales:	13 W
clase de protección:	I
Adecuado para uso en interiores:	Ja
Longitud del paquete:	303 mm
Regulable:	Ja
Tipos de lámparas compatibles:	LED
Potencia máxima de la lámpara de repuesto:	15 W
Ángulo de haz:	50 °
Doblar:	Ja
Lámpara(s) incluida(s):	Ja
estilo ligero:	Modern
Temperatura de color (máx.):	- K
Ubicación adecuada:	Bedroom, Living room, Office, Study
Frecuencia-de-entrada-de-CA:	50 - 60 Hz
Tipo-producto:	Oppervlak-spotverlichting
Ampliación de tamaño extra:	Ja
Incluyendo el tipo de lámpara(s):	LED
Se puede utilizar en combinación con un atenuador de pared.:	Ja
Salida-de-luz:	350 lm