StarTech.com AP300WN2X2W Manual de Usario

StarTech.com repetidor wifi AP300WN2X2W

Lee a continuación 📖 el manual en español para StarTech.com AP300WN2X2W (2 páginas) en la categoría repetidor wifi. Esta guía fue útil para 4 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

Quick Start Guide

DE: Bedienungsanleitung - de.startech.com

FR: Guide de l'utilisateur - fr.startech.com

ES: Guía del usuario - es.startech.com

I T: Guida per l'uso - it.startech.com

NL: Gebruiksaanwijzing - nl.startech.com

P T: Guia do usuário - pt.startech.com

Manual Revision: 08/07/2014

For the most up-to-date information, please visit: www.startech.com

Packaging Contents

• 1 x In-Wall Access Point

• 1 x Faceplate

• 1 x Frame for Faceplate

• 2 x Screws

• 2 x Washers

• 1 x Quick Start Guide

• 1 x Instruction Manual CD

System Requirements

• 802.3af / at compatible PoE Switch

• Cat 5e (or better) Ethernet cabling from PoE switch to the Access

Point

• 1 gang receptacle box

LED Indicators

Installation

AP300WN2X2W / AP300WN22WUE

300Mbps Wireless N PoE-Powered Wallplate Access Point

*actual product may vary from photos

Front View

Rear View

Reset Procedure

Default Settings

To reset the unit to factory defaults, press and hold the AUX and

Reset buttons simultaneously for 5 seconds and then release.

Default IP Address: 10.59.1.200

Username / Password: admin / admin

1. Slide the Frame over the back of the AP and secure using the

provided screws w/ washers.

Ethernet Connector

(transparent) LAN Connector AUX Reset

Button

PoE Power / Data

Connector Ethernet Connector

(transparent)

LED DescriptionState

PWR O No power

Green Unit powered on

SYS

O Remains o while the unit is initializing

Green Initializing complete, system is ready to use

Green (Blinking) During rmware upgrades, this system LED will blink

Link/

WAN

O No network connector

Green 10/100Mbps network connection established

Green (Blinking) Indicates WAN activity

LAN

O No network connection

Green 10/100Mbps network connection established

Green (Blinking) Indicates LAN activity

WLAN

O The Wireless is not ready

Green Wireless connection established

Green (Blinking) Indicates Wireless activity

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modications not expressly approved by StarTech.com could void the user’s authority to operate the equipment.

Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation

of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2)l’utilisateur de l’appareil doit accepter tout brouillage

radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

IC Radiation Exposure Statement:

This equipment complies with IC RSS-102 radiation exposure limit set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.Déclaration d’exposition à la radiation: Cet équipement

respecte les limites d’exposition aux rayonnements IC dénies pour un environnement non contrôlé. Cet équipement doit être installé et mis en marche à une distance minimale de 20 cm qui sépare l’élément rayonnant de votre corps.L’émetteur ne doit ni être utilisé avec une autre

antenne ou un autre émetteur ni se trouver à leur proximité.

FCC ID: TWS-WAP-001R2

IC: 11232A-AP300WN2X2W

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent

an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. Regardless of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby

acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.

Technical Support

StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads.

For the latest drivers/software, please visit www.startech.com/downloads

Warranty Information

This product is backed by a two year warranty.

In addition, StarTech.com warrants its products against defects in materials and workmanship for the periods noted, following the initial date of purchase. During this period, the products may be returned for repair, or replacement with equivalent products at our discretion. The

warranty covers parts and labor costs only. StarTech.com does not warrant its products from defects or damages arising from misuse, abuse, alteration, or normal wear and tear.

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business, or any pecuniary loss, arising

out of or related to the use of the product exceed the actual price paid for the product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.

2. Connect an Ethernet cable to the PoE power / data port on the

back of the AP.

3. (Optional) Connect a second Ethernet cable or RJ11 telephone

cable to the transparent Ethernet pass-through port if desired for

telephony or secondary LAN connection.

4. Insert the AP into a standard 1 gang outlet box until it sits ush

with the wall and secure with screws.

5. Attach the Faceplate to the front of the AP and press in so that it

clips into place.

Operation

For complete operating instructions / specications, please visit

www.startech.com/AP300WN2X2W

1. Congure a system to be on the same subnet as the AP (e.g.

10.59.1.8 - 254).

2. Open your preferred web browser and enter the IP address

10.59.1.200 into the address bar, then press Enter.

3. Enter your Username / Password (Default: ) and admin / admin

click Login.

4. Select the section from the left column of the Network Setting

web interface to congure your desired IP address settings and

VLAN information. Click to save your changes.Apply

5. To change the available SSID information and wireless security

settings, select Wireless Setting > Multi-SSID Setting > Edit on

each individual SSID that you would like to enable. Click Apply to

save your changes.

Note: It is strongly recommended to congure security, to avoid

unwanted access to your wireless network.

6. To restrict access to the web interface of your AP, it is also

recommended to congure a password, which can be done by

selecting the Administration Setting section. Click Apply to save

your changes.

Note: It is strongly recommended to change the default security

settings, to avoid unwanted access and/or conguration changes.

Especificaciones del producto

Marca:	StarTech.com
Categoría:	repetidor wifi
Modelo:	AP300WN2X2W
Color del producto:	Zwart
Peso.:	38000 g
Ancho:	145 mm
Profundidad:	195 mm
Altura:	230 mm
Tecnología de conectividad:	Bedraad
Energía promedio:	- W
Consumo de energía (en espera):	1 W
Uso recomendado:	Universeel
Impedancia:	- Ohm
Canales de salida de audio:	1.0 kanalen
Colocación de los altavoces:	Vloer
Número de conductores:	1
altavoz de graves:	Ja
Rango de frecuencia:	64 - 21000 Hz
Sensibilidad:	96 dB
Tipo de altavoz:	2-weg
Amplificador:	Ingebouwd
Diámetro del altavoz de graves:	4 "
tweeter:	Ja
Consumo de energía (típico):	50 W