StarTech.com VDSL-LAN-EXTENDER-1G Manual de Usario
StarTech.com
repetidor wifi
VDSL-LAN-EXTENDER-1G
Lee a continuación 📖 el manual en español para StarTech.com VDSL-LAN-EXTENDER-1G (2 páginas) en la categoría repetidor wifi. Esta guía fue útil para 5 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/2
Quick-Start Guide
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
Manual Revision: October 13, 2023
10/100/1000 Mbps VDSL2 Ethernet Extender Kit - 1km
Product Information
For the latest drivers/software, technical specications, and declarations of
conformance, please visit: www.StarTech.com/VDSL-LAN-EXTENDER-1G
Requirements
• Ethernet Device x 2
• RJ45 Ethernet Cables x 2
• RJ45 or RJ11 Cable x 1
Package Contents
• VDSL Extender x 2
• Mounting Bracket Kits x 2
• Power Supply x 2
• Quick-Start Guide x 1
Installation
(Optional) Mounting the VDSL Extender
Note: Before mounting the make sure that the surface you are VDSL Extender
mounting to is strong enough to support the . It is recommended that VDSL Extender
the is mounted on a wall stud to provide the correct support.VDSL Extender
1. Determine the for the and .Mounting Surface Local Remote VDSL Extender
2. Place the upside down to expose the on VDSL Extenders Mounting Bracket Holes
the . Align the in the with the on VDSL Extenders Holes Mounting Brackets Holes
the bottom of the .VDSL Extenders
3. Insert four through each and into the . Screws Mounting Bracket VDSL Extender
4. Tighten each using a .Screw Phillips Head Screwdriver
5. Mount the to the desired using the appropriate VDSL Extender Mounting Surface
Mounting Hardware (e.g. Wood Screws).
Install the VDSL Extender Kit
1. Position a in each of the locations, local and remote. VDSL Extender
2. Using , ensure that one is in , and the DIP Switch 1 VDSL Extender Master Mode (CO)
other is in .Remote Mode (RT)
Note: If the DIP switches need to be adjusted after the initial setup, both VDSL
Extenders must be powered o before changing the DIP switch settings.
3. Plug in an from the on the local to an RJ45 Ethernet Cable LAN Port VDSL Extender
Ethernet Port Ethernet Device on the local .
4. Plug in an from the on the remote to RJ45 Ethernet Cable LAN Port VDSL Extender
an on the remote .Ethernet Port Ethernet Device
5. Plug in a or from the of the local , to the RJ45 RJ11 Cable VDSL2 Port VDSL Extender
VDSL2 Port VDSL Extender of the remote .
6. Connect the included to each of the .Power Adapters VDSL Extenders
Product ID
VDSL-LAN-EXTENDER-1G
Component Function
1DIP Switches
• Set the Mode or change settings on the VDSL
Extenders
• Refer to DIP Switch Chart
2LAN Port • Connect to an on and RJ45 Port Local Remote
Equipment
3LAN Status LEDs Refer to the • LED Chart
4VDSL2 Status LEDS Refer to the• LED Chart
5VDSL2 Port • Use a or to connect the Local RJ45 RJ11 Cable
and Remote togetherVDSL Extenders
6Power Input Port • Connect the included Power Adapter
• Located on the rear of each VDSL Extender
2
1 3 4 5
Regulatory Compliance
FCC - Part 15
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Changes or modications not expressly approved by StarTech.com could
void the user’s authority to operate the equipment.
Industry Canada Statement
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [A] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (A)/NMB-3(A)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two
conditions:
(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Warranty Information
This product is backed by a two year warranty.
For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)
for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss
of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the
product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the
limitations or exclusions contained in this statement may not apply to you.
Use of Trademarks, Registered Trademarks, and other Protected Names and
Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-
party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which
this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the
property of their respective holders.
FR: startech.com/fr
DE: startech.com/de
ES: startech.com/es
NL: startech.com/nl
IT: startech.com/it
JP: startech.com/jp
StarTech.com
Ltd.
45 Artisans Cres
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Rd,
Brackmills
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
4490 South Hamilton
Road
Groveport, Ohio
43125
U.S.A.
StarTech.com Ltd.
Siriusdreef 17-27
2132 WT Hoofddorp
The Netherlands
DIP Switches
Note: The VDSL Extender that is set to Remote mode will always follow the settings set
on the Master VDSL Extender. When set to Remote Mode, DIP Switches 2, 3, and 4 have
no function.
LED Chart
LED Colour Blink On O
PWR Green N/A Powered On Powered O
RT Green N/A RT (Remote) CO (Master)
LNK Green Slow: Idle
Fast: Training VDSL2 Link Up VDSL2 Link
Down
10 Green Data Activity 10Mbps Link Down
100 Green Data Activity 100Mbps Link Down
1000 Green Data Activity 1000Mbps Link Down
VDSL2 Port Pinout
Pin Description
1N/A
2N/A
3N/A
4Analog Input/Output
5Analog Input/Output
6N/A
7N/A
8N/A
Especificaciones del producto
| Marca: | StarTech.com |
| Categoría: | repetidor wifi |
| Modelo: | VDSL-LAN-EXTENDER-1G |
¿Necesitas ayuda?
Si necesitas ayuda con StarTech.com VDSL-LAN-EXTENDER-1G haz una pregunta a continuación y otros usuarios te responderán
repetidor wifi StarTech.com Manuales
15 Septiembre 2024
15 Septiembre 2024
2 Septiembre 2024
1 Septiembre 2024
31 Agosto 2024
30 Agosto 2024
29 Agosto 2024
29 Agosto 2024
29 Agosto 2024
repetidor wifi Manuales
- repetidor wifi Xiaomi
- repetidor wifi Medion
- repetidor wifi Allnet
- repetidor wifi Edimax
- repetidor wifi Strong
- repetidor wifi Hikvision
- repetidor wifi Silvercrest
- repetidor wifi Gembird
- repetidor wifi Asus
- repetidor wifi Renkforce
- repetidor wifi Sitecom
- repetidor wifi TP Link
- repetidor wifi Black Box
- repetidor wifi Vision
- repetidor wifi Axis
- repetidor wifi AVM
- repetidor wifi Totolink
- repetidor wifi Cisco
- repetidor wifi Engenius
- repetidor wifi Envivo
- repetidor wifi Digitus
- repetidor wifi Devolo
- repetidor wifi Linksys
- repetidor wifi Buffalo
- repetidor wifi Netgear
- repetidor wifi LevelOne
- repetidor wifi Mercusys
- repetidor wifi Planet
- repetidor wifi Western Digital
- repetidor wifi D-Link
- repetidor wifi Essentiel B
- repetidor wifi Fluke
- repetidor wifi Marmitek
- repetidor wifi Ubiquiti Networks
- repetidor wifi Mikrotik
- repetidor wifi Hawking Technologies
- repetidor wifi Crestron
- repetidor wifi Smart-AVI
- repetidor wifi SIIG
- repetidor wifi Extron
- repetidor wifi KanexPro
- repetidor wifi DTRONIC
- repetidor wifi Cudy
- repetidor wifi Lindy
- repetidor wifi HELGI
- repetidor wifi Amped Wireless
- repetidor wifi Ruckus Wireless
- repetidor wifi Axing
- repetidor wifi EXSYS
- repetidor wifi Gewiss
- repetidor wifi Seco-Larm
- repetidor wifi NetComm
- repetidor wifi Altronix
- repetidor wifi Juniper
- repetidor wifi ALC
- repetidor wifi Comtrend
- repetidor wifi Universal Remote Control
- repetidor wifi IDIS
- repetidor wifi CSL
Últimos repetidor wifi Manuales
14 Octubre 2024
10 Octubre 2024
10 Octubre 2024
3 Octubre 2024
3 Octubre 2024
30 Septiembre 2024
30 Septiembre 2024
29 Septiembre 2024
29 Septiembre 2024
28 Septiembre 2024