STI SS-2322-EV-ES Manual de Usario

STI Cambiar SS-2322-EV-ES

Lee a continuación 📖 el manual en español para STI SS-2322-EV-ES (8 páginas) en la categoría Cambiar. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/8
Installation and Service Instructions
Stopper® Station Series Push Button
Models SS2xx2, SS2xx5, SS2xx9
Switch Rating
2 Form C Contacts LTUL Models
125/250 VAC, 10A, ½ HP Form “C” Contacts on Timer
30 VDC, 6A Rated 30 VDC 3A
ADA
Compliant
We protect the things that protect you.®
NOTE For LTUL Models, Form “C” contacts on timer, Rated 30 VDC 3A, the enclosed timer is to be used
and installed per the enclosed LT-1UL installation sheet. LTUL Models, Form “C” contacts on timer, Rated
30 VDC 3A maximum rating 30 VDC 3A. For access control installations, power for the LT-1 Timer must
be supplied by a power source listed to UL294. When used for access control, this device shall be used
as part of an access controlled egress door system. It is up to the local AHJ to allow use of this device in
place of an automatic sensor. For higher security installations, lower time limits should be used.
REMARQUE Pour les modèles LTUL Models, Form “C” contacts on timer, Rated 30 VDC 3A, la minuterie
intégrée doit être installée et utilisée suivant la fiche d’installation LT-1UL fournie. La cote maximale des
modèles LTUL Models, Form “C” contacts on timer, Rated 30 VDC 3A est de 30 VCC 3A. Pour les
installations de contrôle d’accès, l’alimentation de la minuterie LT-1 doit être fournie par une source
homologuée UL294. Lorsque cet appareil est utilisé aux fins de contrôle d’accès, il doit faire partie d’un
système de porte de sortie à accès contrôlé. Il incombe donc à l’AHJ local d’autoriser l’utilisation de cet
appareil au lieu d’un capteur automatique. Pour les installations de sécurité plus renforcée, des délais
inférieurs doivent être utilisés.
- 2 -
Wire Connections
CONTACT
SET 1
CONTACT
SET 2
CONTACT BOX CONTAINS
TWO CONTACT SWITCHES
NC
NO
NC
NO
COM
COM
NO
NC
COM
9 in. QUICK CONNECT WIRE LEAD
(6) PROVIDED
MAKE SURE LEAD IS
FULLY CONNECTED TO
MOUNTING TAB
ASSUREZ-VOUS QUE
LE FIL EST ENTIÈREMENT
CONNECTÉ À LA PATTE
DE MONTAGE
Housing Removal
BUTTON AND SWITCH ASSEMBLY
SWITCH HOUSING
ALLEN HEAD SCREW
#8-32 x 3/8 in.
(1) PROVIDED
3/32” HEX WRENCH
(1) PROVIDED
Procedure
1. Remove screw.
2. Pull bottom of housing out and lift up until tabs are released from slots
in top of switch assembly.
- 3 -
Product Dimensions
1.62 in.
(41mm)
1.58 in.
(40mm)
MODELS
WITH BACK BOX
MODELS
WITHOUT BACK BOX
1.62 in.
(41mm)
1 in.
(25mm)
3.22 in.
(82mm)
4.86 in.
(123mm)
COM
NO
NC
Installation
BUTTON ILLUMINATION WIRING
12-24 VAC/VDC, 21mA EACH COLOR
BLACK - GROUND
WHITE - WHITE LED (+)
GREEN - GREEN LED (+)
RED - RED LED (+)
WHITE
BLACK
GREEN
RED
INSULATING
BUSHING
SCREW #6-32 x 1 in.
(2) PROVIDED
BUTTON CAP
(PUSH SHOWN)
SCREW
#6 x 1-1/4 in.
(4) PROVIDED
BUTTON AND SWITCH ASSEMBLY
(SHOWN ILLUMINATED - OPTIONAL)
ANCHOR
(4) PROVIDED
DRILL (4)
3/16 in. DIA. HOLES
OPTIONAL SURFACE
MOUNT BACK BOX
DRILL POINT LOCATION PROVIDED TOP AND BOTTOM
FOR 1/2” CONDUIT FITTINGS. DRILL AS NEEDED.
BUTTON ILLUMINATION*
ASSEMBLY (OPTIONAL)
BUTTON CAP
ALIGNMENT HOLE
BUTTON ILLUMINATION WIRES*
NOTE
ADA MOUNTING COMPLIANCE REQUIRES THE OPERABLE PART OF
THE INITIATING DEVICE SHALL NOT BE LESS THAN 1.1 m (3 ½ ft.) OR
GREATER THAN 1.37m (4 ½ ft.) ABOVE FINISHED FLOOR SURFACE.
*

Especificaciones del producto

Marca: STI
Categoría: Cambiar
Modelo: SS-2322-EV-ES

¿Necesitas ayuda?

Si necesitas ayuda con STI SS-2322-EV-ES haz una pregunta a continuación y otros usuarios te responderán




Cambiar STI Manuales

Cambiar Manuales

Últimos Cambiar Manuales