Swann SWALPH-B12003HRB Manual de Usario

Swann No categorizado SWALPH-B12003HRB

Lee a continuación 📖 el manual en español para Swann SWALPH-B12003HRB (12 páginas) en la categoría No categorizado. Esta guía fue útil para 5 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/12
TripleHead Wireless
Motion Sensor
Spotlight
with Remote Control
Powered by Swann
INSTRUCTION MANUAL
EN
MANUAL DE INSTRUCCIONES
ES
2
EN
Adjustable Light Panels (1200 Lumens)
Power OFF.
The spotlight will revert to auto
(sensor) mode after 1 hour if no
other button is pressed
Set light panels to stay OFF
when motion is detected
Set Enforcer Lights to stay OFF
when motion is detected
Set motion sensor sensitivity to
Low. Detection range is up to
10ft/3m
Set motion sensor sensitivity
to Medium. Detection range is
up to 13ft/4m
*Override sensor and manually turn
light panels ON for an indenite
amount of time until the Power OFF
button is pressed
Infrared (IR) signal transmitter
Set light panels to automatically
turn ON when motion is detected.
Light panels will turn off 20 seconds
after no motion is detected
Set Enforcer Lights to automatically
turn ON when motion is detected.
Enforcer Lights will turn off 20
seconds after no motion is detected
Set motion sensor sensitivity to
High. Detection range is up to
20ft/6m
Override sensor and manually turn
light panels ON for 10 minutes.
After 10 minutes light panels
will turn off and operate in auto
(sensor) mode
Blue Enforcer Flashing
LED Light
Light Sensor
Passive Infrared
Motion Sensor
Mounting Bracket
To remove, press tab
and slide out
The ambient light sensor prevents the
spotlight from automatically activating
during the daytime to preserve battery life.
* Keeping the light panels on
continuously for prolonged periods of
time will signicantly shorten battery
lifespan and reduce operating time.
Spotlight
Remote Control
OVERVIEW
Red Enforcer Flashing
LED Light
3
EN
Spotlight
The spotlight requires four size batteries (not supplied). For reliable, long-lasting D
performance, use only high quality alkaline batteries. To install batteries (see ):Figure 1
Remote Control
1. Unscrew the six screws securing the battery compartment cover on the rear of the
spotlight with a Philips screwdriver and lift it off.
2. Insert batteries according to the polarity markings (+ and -) indicated inside the
battery compartment.
3. Replace the battery compartment cover and screw it back into place with the
previously removed screws.
Figure 1
Figure 2
CR2025
PUSH
Locking Screw
BATTERY INSTALLATION
The remote control is powered by a battery which comes pre-installed. CR2025
To activate the battery, simply pull the plastic lm out from the bottom of the
remote control.
To replace the battery, remove the locking screw on the back of the remote control
using a small Phillips screwdriver, then push the tab on the left of the battery tray
towards the right and pull out the battery tray from the remote control (see Figure
2). Place a new "CR2025" battery on the tray with the positive (+) side facing up.
Insert the tray back into the remote control and secure with the locking screw.
WARNING! THIS PRODUCT CONTAINS A COIN CELL BATTERY.
If swallowed, a lithium coin cell battery can cause severe or fatal injuries within 2 hours.
The battery is hazardous if swallowed, keep out of reach of children.
If the battery compartment does not close securely, stop using the product.
If you think the battery may have been swallowed or placed inside any part of the body, seek immediate
medical attention.

Especificaciones del producto

Marca: Swann
Categoría: No categorizado
Modelo: SWALPH-B12003HRB

¿Necesitas ayuda?

Si necesitas ayuda con Swann SWALPH-B12003HRB haz una pregunta a continuación y otros usuarios te responderán




No categorizado Swann Manuales

No categorizado Manuales

Últimos No categorizado Manuales