TCW Technologies SS-12v Manual de Usario

TCW Technologies No categorizado SS-12v

Lee a continuación 📖 el manual en español para TCW Technologies SS-12v (8 páginas) en la categoría No categorizado. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/8

SmartStart

Model: SS-12v

SmartStart is an electronic control module for the engine starter system on

aircraft. SmartStart improves the safety and security of push-button or key-

switch starting systems by providing an interlocked and time limited operation of

the engine starter. SmartStart controls standard aviation starter contactors and

provides simple integration of control stick switch or panel mounted start

switches. SmartStart includes inputs for interlock and arming switches and

provides a 1 minute timer for activating the starter contactor. The SmartStart

system helps avoid unintentional activation of the engine starting system.

SS-12v is not TSO’d and must only be used in aircraft certified in the

Experimental category.

SS-12v must be installed using the current aircraft standards and

practices. Refer to AC 43.13-2A/1B. The installer/builder is solely responsible

for determining the suitability of the installation and use of this product.

Important Notes:

1) SmartStart has an optional Interlock Switch input that may be used to

enable/disable the start contactor. Door/canopy switches may be used to

ensure the engine cannot be started until the door/canopy is properly closed.

This input is a closure to ground to ENABLE the system.

2) It is recommended that the Arming Switch be hidden from view to improve

theft resistance of the aircraft.

3) If using a traditional aircraft keyed mag/start switch and an optional interlock

switch is used, then the terminal marked “Bat” on the key switch is connected to

pin 4, “armed power” on SmartStart.

4) Two wiring diagrams are provided, one with and one without the use of an

interlock switch.

5) All switches used with SmartStart are of the momentary type and need no

particular current rating. The switching of the start contactor is done

electronically with no moving parts and includes fly-back diode protection for the

start contactor.

6) An optional “Armed LED” indicator may be driven from the SmartStart module.

The maximum current on this pin is 50 mA. Do not use with incandescent

indicator lamps. If this feature is unused, leave this pin un-populated in the

connector.

7) An optional Airspeed Switch, model ASW-2, may be connected in parallel with

the arming switch. The use of the airspeed switch will allow in flight restarting

without the need to press the arming switch. When the aircraft is above the

airspeed switch set point (factory calibrated at 40 knots) the arming circuit is

continuously made thereby ensuring the start switch is always active in flight.

Installation instructions:

1) Select an installation diagram that matches the required installation. Diagrams

are provided for installations with and without an interlock switch connection.

Wire aircraft harness per appropriate diagram.

2) Provide power to the SmartStart module through a 5 amp fuse or breaker.

3) The SmartStart module uses a standard 9 pin D-sub connector with the male

pins on the module. Terminate the harness wires in a mating female D-sub

connector.

4) If desired, mount the “Armed LED” on the instrument panel.

5) Mount the SmartStart module in the aircraft using the mounting tabs provided.

DO NOT mount the module in the firewall forward area.

6) If using the optionally ASW-2 airspeed switch, mount the airspeed switch via

the mounting tabs and connect the static and pitot lines to the marked ports.

The barbed fittings are sized for ¼” OD pitot and static line with a nominal ID of

3/16”. Connect the two terminals of the ASW-2 switch in parallel with the two

terminals of the arming switch.

Product operation:

If using a system that includes an interlock switch, ensure the switch is

closed. When prepared to start the aircraft engine, momentarily press the

armed switch. The activation of the arming swtich initiates a 1 minute timer,

during the 1 minute time interval closure of the Start Switch will engage the start

contactor. During the 1 minute timer interval the “Armed LED” will be

illuminated, providing feedback to the pilot that the start system is active. If the

system is installed with an optional ASW-2 airspeed switch, then the starter

system will always be armed when the aircraft is above the airspeed set-point.

TCW Technologies, LLC.

2955 Main Road East

Emmaus, PA 18049

610-928-3420

www.tcwtech.com

email: support@tcwtech.com

Especificaciones del producto

Marca:	TCW Technologies
Categoría:	No categorizado
Modelo:	SS-12v
Tipo de operación:	Knoppen
Color del producto:	Black, Stainless steel, Transparent
Amable:	Staafmixer
Fácil de limpiar:	Ja
Fuente-de-alimentación:	AC
Activos:	600 W
Contenido contenedor/lata:	0.6 l
Hoja de acero inoxidable:	Ja
No contiene:	Bisfenol A / BPA
jardín:	Ja
Material-del-cuchillo:	Roestvrijstaal
cortador fino:	Ja
taza medidora:	0.55 l
voltaje-de-entrada-de-CA:	220-240 V
Frecuencia-de-entrada-de-CA:	50/60 Hz
Taza:	Ja