Technoline WS 9310 Manual de Usario

Lee a continuación 📖 el manual en español para Technoline WS 9310 (9 páginas) en la categoría Estación meteorológica. Esta guía fue útil para 7 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/9
Holder
Detachable stand
WEATHER STATION
INTRODUCTION:
Congratulations on purchasing this innovative 433MHz Weather Station which displays the weather forecast, time,
indoor temperature, and up to three outdoor temperature readings. To enjoy the full benefits of this innovative product,
please read this operating manual.
Weather Station:
FEATURES:
DCF radio-controlled time reception
LCD clock in 24 hour time display
Indoor and outdoor temperature reading in degree Celsius (°C)
Indoor and outdoor temperature with Minimum and Maximum records
Weather tendency indicator and weather icons
Can receive up to three Outdoor transmitters
Table standing or wall mountable (detachable table stand)
Hanging hole Temperature Transmitter:
SETTING UP:
Please follow these steps to ensure that your new Weather Station works correctly with the temperature
transmitter(s):
Function Keys
Battery
compartment
1. First, insert 2 x AA, IEC LR6, 1.5V batteries into the Weather Station. Once the batteries are in place, all
segments of the LCD will light up briefly. Then the indoor temperature, the time as -:--, and the weather icons
sun and clouds will be displayed. If the indoor temperature is not displayed after a few seconds, remove the
batteries and wait for at least 30 seconds before reinserting them. Once the indoor temperature is displayed
proceed to step 2.
Battery
compartment
2. Within 1-1/2 minutes of activating the Weather station, place 2 x AAA, IEC LR3, 1.5V batteries into the
transmitter.
3. After a few seconds of inserting the batteries into the transmitter, the Weather Station will start receiving data
from the transmitter. The remote temperature will then be displayed on the Weather Station. If this does not
happen after 2 minutes, the batteries will need to be removed from both units and reset from step 1.
4. The Weather Station can take up to 3 remote transmitters. If you have purchased additional transmitters, follow
step 2 for all extra transmitters. However, ensure that you leave 10 seconds in between the reception of the
last transmitter and the set-up of the following transmitter. The Weather Station will number the transmitters in
the order of set-up, i.e. the first transmitter will have the temperature displayed with the channel number 1
against it and so on.
Note: No channel number will show up if there is only one transmitter used.
5. When all the transmitters are set up, there is a testing period, during which the display switches quickly
between all the received transmitters at random, according to which random transmission it receives. Pressing
any key will stop this process and the display will show the temperature for the first transmitter. The process
also stops automatically if no keys are pressed for a few minutes.
6. The DCF-77 time code reception is automatically started just after the Weather Station is activated. This takes
typically between 3 - 5 minutes in good conditions. This time period is an excellent opportunity to locate the
transmitter(s) in suitable location(s) outdoors. In order to ensure sufficient 433 MHz transmission however, this
should under good conditions be no more than 25 meters from where the Weather Station will be finally
positioned (see notes on “Positioning” and “433 MHz Reception”).
7. If after 10 minutes the DCF time has not been received, use the SET key to manually enter a time initially. The
clock will automatically attempt each hour to receive the DCF time. When this is successful, the received time
will override the manually set time.
Note:
Should the total time of inserting the batteries into the transmitters take longer than 1-1/2 minutes from the time of
inserting the batteries into the Weather Station then temperature reception problems may occur. If the temperature is
Battery cover
Battery cover
Battery compartment
not being received, then see Checking for 433MHz reception, before resetting the units (see Resetting the
Weather Station below).
In the event of changing batteries in any of the units, all units need to be reset by following the setting up procedures.
This is because the transmitter at start-up assigns a random security code and this code must be received and stored
by the Weather Station in the first 1-1/2 minutes of power being supplied to it.
BATTERY CHANGE:
It is recommended to replace the batteries in all units on an annual basis to ensure optimum accuracy of these units.
Please participate in the preservation of the environment. Return used batteries to an authorized
depot.
LCD SCREEN
The Weather Station’s LCD is split into 3 sections displaying the information for time, weather forecast, indoors and
outdoors.
After unit reset, all the segments will light up momentarily before displaying:
1. Weather Icon
2. Time “-:--“
3. Indoor temperature in degree Celsius (°C)
4. Hidden Max/Min icon for Indoor/Outdoor Temperature
5. Outdoor Temperature in °C and transmitter identification number
Weather Tendency
Indicator
TIME SETTING:
When the setting up procedures are completed but DCF time has not been received, the time can be set manually.
Outdoor temperature
in ºC Transmitter
identification
number
Time
Indoor temperature
in ºC
Weather Icon
DCF Tower icon
(for time reception)
Outdoor temperature
reception indicator

Especificaciones del producto

Marca: Technoline
Categoría: Estación meteorológica
Modelo: WS 9310

¿Necesitas ayuda?

Si necesitas ayuda con Technoline WS 9310 haz una pregunta a continuación y otros usuarios te responderán




Estación meteorológica Technoline Manuales

Estación meteorológica Manuales

Últimos Estación meteorológica Manuales