Varo MOTSA23EL Manual de Usario

Varo Kluis MOTSA23EL

Lee a continuación 📖 el manual en español para Varo MOTSA23EL (2 páginas) en la categoría Kluis. Esta guía fue útil para 7 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

MOTSA23EL EN

OPERATING INSTRUCTIONS

CAUTION: Do not keep the keys in the safe.

1 TO OPEN THE SAFE

To open the door of the safe for the ﬁrst time: remove the small plastic cover ( B , see diagram “ ”

1) on the front panel, insert the key into the key hole and turn it counter-clockwise direction, at

the same time, turn the doorknob ( A , see diagram 1) clockwise direction to open the safe. “ ” in

2 INSTALLING THE BATTERIES

The safe requires 4×size “AA” (1.5V) batteries.

Open the safe, push the battery cover plate “D” (see diagram 2) on the back of the door and

install the batteries. Ensuring the batteries are ﬁtted with the correct corresponding polarity.

Use of alkaline batteries is recommended.

3 PROGRAMMING THE CODE

A. With the safe door open press the red button on the back of the door near the hinge, “C”

release it and you will hear two beeps. The yellow light will be on at the same time.

B. Now press from 3 to 8 numbers that you wish to use as a combination, and conﬁrm by

pressing the letter A in 15 seconds. The safe bleeps twice and the yellow light “ ” or “B” with “ ”

will go oﬀ, your personal code is now set.

C. Write down your new combination immediately and check whether your new combination

has been programmed or not with the safe door open.

4 USING YOUR SAFE

To open the safe, enter your personal code followed by the letter A B , you will hear a “ ” or “ ”

beep and the green light will be on, then turn the doorknob in clockwise direction to open the

door within 5 seconds.

If you or an intruder uses the incorrect group of numbers, it will not open. If the incorrect

combination is used 3 times consecutively, you must wait for 20 seconds before reattempting.

If again the incorrect combination is selected 3 times, you must wait approximately 5 minutes

before reattempting access.

5 BATTERY REPLACEMENT WARNING

If the batteries are low, the red light (in the middle) will warn you immediately. To test the

batteries, just input your personal numbers to open the door. If the batteries are low, the red

light will be on. If nothing happens the batteries are . ok

6 REPLACING THE BATTERIES

The safe requires 4× si Open the safe, push the battery cover ze “AA” (1.5V/ R06) batteries.

plate on the back of the door and replace the 4 pcs old batteries. You must reprogram the

code, using the above step nr. 3.

Use of alkaline batteries is recommended.

7 OPENING THE SAFE MANUALLY OVERRIDE INSTRUCTION TO

OPEN THE SAFE

For your convenience, we have engineered a manual override system for your safe. If you

forget or misplace your combination, remove the small central plate on the front panel B(“ ”,

see in diagram 1), insert the key into the keyhole and turn it in a counter-clockwise direction,

then turn the knob ( A , see in diagram 1) in a clockwise direction towards the right. This will “ ”

manually open your safe at any time.

MOTSA23EL EN

8 INSTALLING THE SAFE

To reduce the risk of theft of the safe, it can be secured to wall or inside a drawer. For your a

convenience, there are pre-drilled holes (diameter 8 mm) on the safe, and it can be ﬁxed by

the expansion bolts supplied.

CAUTION: The safe should be installedhorizontally.

Especificaciones del producto

Marca:	Varo
Categoría:	Kluis
Modelo:	MOTSA23EL
Color del producto:	Aluminium, Black
Peso.:	250 g
Ancho:	58 mm
Profundidad:	128 mm
Altura:	55 mm
factor vorm:	Doos
Soporte de colocación:	Binnen
Tecnología de conectividad:	Bedraad
red LAN:	Nee
Resolución Máxima:	768 x 494 Pixels
Salida de corriente (voltios):	+12V
Iluminación mínima:	0.4 Lux
Disco duro incorporado:	Nee
Vision nocturna:	Ja
Formato de señal analógica:	NTSC, PAL
Tamaño del sensor óptico:	1/3 "
Tipo de sensor de imagen:	CCD
Zoom óptico:	- x
Velocidad de obturación de la cámara:	1/50 (1/60) - 1/100000 s
Interfaz:	BNC
balance de blancos:	Auto
Salida de vídeo compuesto:	1
Relación señal-ruido:	48 dB
Control PTZ:	Nee
Número de líneas de televisión:	520
Modo día/noche:	Ja
Wifi.:	Nee
voltaje-de-entrada-de-CA:	100-240 V
Temperatura de funcionamiento (TT):	0 - 50 °C
Humedad relativa de funcionamiento (VV):	20 - 80 procent
Número F (apertura relativa):	1.2
Resoluciones NTSC:	768 x 494 Pixels
Resoluciones PAL:	752 x 582 Pixels