Winegard TRAV'LER SKA-733 Manual de Usario

Winegard antena de televisión TRAV'LER SKA-733

Lee a continuación 📖 el manual en español para Winegard TRAV'LER SKA-733 (4 páginas) en la categoría antena de televisión. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/4
TRAV’LER®
Automatic Multi-Satellite TV Antenna
Model SKA-733 Reector & Bracket
INSTALLATION MANUAL
Made in the U.S.A.
Printed in U.S.A. © Winegard Company 2012 1/12 2452259
WINEGARD®
TRAV’LER® SHAW DIRECT Reector and Bracket Installation
Check to be sure that there is nothing above the TRAV’LER antenna that might
prevent it from raising. You will need at least 40” of clearance above the TRAV’LER
mount to ensure that you have room to install the reector. Pay attention to these Pinch
Points as the antenna raises.
Raise Antenna:
There are two ways to raise the antenna, automatic or manual; each is explained below.
A. Automatic:
Steps 1-7 explain how to use the TRAV’LER Interface Box to raise the mount.
1. Press and hold for 2 seconds to turn “ON” the TRAV’LER Interface Box. Wait until the [POWER]
 InterfaceBoxnishes“connectingtoantenna”.
* The TRAV’LER may enter the “Search Routine” after 10 seconds; this is normal (See NOTE Below).
2. Press [ENTER] and hold for 2 seconds or until the unit displays “Enter User Menu”. Press [SELECT] to
move the asterisk to “Yes”. Press [ENTER].
3. Press to move the asterisk to INSTALLATION.[SELECT]
4. Press You will be asked to provide a code to enter the Installation Menu.[ENTER].
5. Press 4 times to enter code 0000. [ENTER]
6. Press to move the asterisk to RAISE ANTENNA. Press Press to move [SELECT] [ENTER]. [SELECT]
the asterisk to Yes.
7. Press The TRAV’LER mount will raise up about half way. [ENTER].
* NOTE: If the TRAV’LER enters the “Search Routine,” and the TRAV’LER mount raises more than 1/2 way be-
fore RAISE ANTENNA is selected (See Step 6), the TRAV’LER will hit its Upper Hard Stop and “Motor Stall” will
appear. This is Normal.
The “Motor Stall” means the TRAV’LER is all the way up and the mount cannot raise any more. There are two
easy ways to clear the “Motor Stall”.
a. Press [ENTER] the TRAV’LER antenna will return to the “Installation Menu”
OR
b. Press [POWER] the TRAV’LER antenna will stow and turn “OFF” (Restart at Step 1).
FIGURE 1
!
2
NOTE: Pinch Points are called out both for your safety and to protect the cables. Ca-
bles will be damaged if installed incorrectly. See pages 3-4 in this installation manual.
Rev. 4/09
4
Be Careful not to strip out the hole for the 5/16 inch
screws when you replace the clamp holding the
coax cables to the arm. DO NOT use a power tool.
!
8. With the Bracket mounted securely, connect the four Coax Cables to the Mount, as shown in Figure 6.
9. Find the Cable Tie on the coax cables
that you have just connected to the mount. Place the
coax cable clamp on the cables just below this cable
tie. Carefully screw this clamp to the front of the Lift Arm
using the 5/16 inch screw provided. See Figure 5.
DO NOT over tighten this screw.
NOTE: If the cable tie is missing, install the clamp 14” from
the end of the connectors.
Calibrate the Elevation Motor:
1. Press and hold for 2 seconds to turn “ON” the TRAV’LER Interface Box. Wait until the [POWER]
 InterfaceBoxnishes“connectingtoantenna”.
2. Press and hold for 2 seconds or until the unit displays “Enter User Menu”. Press [ENTER]
to move the asterisk to “Yes”. Press . [SELECT] [ENTER]
3. Press to move the asterisk to INSTALLATION.[SELECT]
4. Press . You will be asked to provide a code to enter the Installation Menu. [ENTER]
5. Press 4 times to enter code 0000.[ENTER]
6. From the Installation Menu,
7. Press to move “ * ” to “Calibrate EL” and Press . [SELECT] [ENTER]
8. Press to move “ * ” to YES.[SELECT]
9. Press to start the elevation calibration procedure. The LCD should now display [ENTER]
“ Calibrate EL In Progress ...”.
10. After a few moments the IDU LCD will display
“On EL Hard Stop?
Yes *No”.
Visually examine the antenna to verify that the antenna is against the Hard Stop. The antenna will be pointing as
far up as it can go, this is the Hard Stop.
11. Press once to move asterisk to “Yes” if antenna is on the Hard Stop.[SELECT]
12. Press and the LCD will display “Calibrate EL Success”.[ENTER]
13. Press and Hold for 2 seconds to to stow the antenna.[POWER]
FIGURE 6
Coax
Connections

Especificaciones del producto

Marca: Winegard
Categoría: antena de televisión
Modelo: TRAV'LER SKA-733

¿Necesitas ayuda?

Si necesitas ayuda con Winegard TRAV'LER SKA-733 haz una pregunta a continuación y otros usuarios te responderán


antena de televisión Winegard Manuales

Winegard

Winegard Playmaker Manual de Usario

9 Septiembre 2024
Winegard

Winegard TRAV'LER SK-7002 Manual de Usario

9 Septiembre 2024
Winegard

Winegard Sensar III GS-2200 Manual de Usario

9 Septiembre 2024
Winegard

Winegard FL5500A Manual de Usario

9 Septiembre 2024
Winegard

Winegard TRAV'LER SKA-733 Manual de Usario

9 Septiembre 2024

antena de televisión Manuales

Últimos antena de televisión Manuales

Thomson

Thomson ANT1538BK Manual de Usario

15 Octubre 2024
Xoro

Xoro HAN 150 Manual de Usario

11 Octubre 2024
One For All

One For All SV 9482 Manual de Usario

9 Octubre 2024
Kathrein

Kathrein ESU 57 Manual de Usario

6 Octubre 2024
Uniden

Uniden AW880BKL Manual de Usario

4 Octubre 2024
One For All

One For All SV 9435 Manual de Usario

30 Septiembre 2024
Blaupunkt

Blaupunkt Shark Line A-R T 06-M Manual de Usario

23 Septiembre 2024
Uniden

Uniden ATX970W Twin Manual de Usario

18 Septiembre 2024
TP Link

TP Link TL-ANT5819MS Manual de Usario

18 Septiembre 2024
EMOS

EMOS J0704 Manual de Usario

17 Septiembre 2024