Xaoc Tirana II Manual de Usario

Xaoc No categorizado Tirana II

Lee a continuaciรณn ๐Ÿ“– el manual en espaรฑol para Xaoc Tirana II (6 pรกginas) en la categorรญa No categorizado. Esta guรญa fue รบtil para 4 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Pรกgina 1/6
utility micro
sequencer ii
Model of 1960
operatorโ€™s manual rev. 1960/2.0
Thank you for purchasing this Xaoc Devices
product. Tirana is a compact, expandable volt-
age source with a wide range of uses including
classic step sequencer, modulation source, volt-
age bank, and arpeggiator.
Tirana is equally suited to small and large sys-
tems alike, either as a single utility or chained
with more Tirana units. This is a second, vastly
improved revision to the original 2014 Tirana,
featuring an updated circuit and a new, more
๎‚’๎‚‘๎‚™๎‚‡๎‚”๎‚ˆ๎‚—๎‚Ž๎€ƒ๎”๎‚‹๎‚”๎‚๎‚™๎‚ƒ๎‚”๎‚‡๎‡ค
The module requires 6hp worth of free space
in the eurorack cabinet. The ribbon type pow-
er cable must be plugged into the bus board,
paying close attention to polarity orientation.
The red stripe indicates the negative 12V rail
and is supposed to match a dot, or โ€“12V red
stripe marks on both the unit and the bus
board. The module itself is secured against
reversed power connection, however revers-
ing the 16-pin header may cause serious
damage to other components of your system,
because it will short-circuit the +12V and +5V
power rails. The module should be fastened by
mounting the supplied screws before power-
ing up. To better understand the device, we
strongly advise the user to read through the
entire manual before using the module.
To operate, Tirana expects an external clock
source (up to 320Hz) in the clock input sock-
et . Patching any stable clock generatorโ€”
such as an LFO pulse or another sequencerโ€™s
sync outputโ€”causes the sequence steps to
play sequentially in a loop. The value for each
step is adjustable by turning knobs 1-4 . By
default, the voltage set by the knob is unipolar
and within the 0V to 10V range. The jumper
on the back of the module allows for the
selection of bipolar voltages within โ€“5 to +5V
range. Another jumper attenuates the volt-
age range to 0V to 5V and โ€“2.5V to +2.5V re-
๎‚•๎‚’๎‚‡๎‚…๎‚–๎‚‹๎‚˜๎‚‡๎‚Ž๎‚›๎€ƒ๎ˆ‹๎‚•๎‚‡๎‚‡๎€ƒ๎”๎‚‹๎‚‰๎‡ค๎€ƒ๎ธ๎ˆŒ๎‡ค๎€ƒ๎€Š๎‚‡๎‚๎‚‡๎‚”๎‚ƒ๎‚–๎‚‡๎‚†๎€ƒ๎‚…๎‚‘๎‚๎‚–๎‚”๎‚‘๎‚Ž๎€ƒ๎‚˜๎‚‘๎‚Ž๎‚–-
ages and gate/trigger impulses are available
at cv out and gate outputs.
๎€Š๎‚ƒ๎‚–๎‚‡๎ˆ€๎‚–๎‚”๎‚‹๎‚‰๎‚‰๎‚‡๎‚”๎€ƒ ๎‚…๎‚ƒ๎‚๎€ƒ ๎‚„๎‚‡๎€ƒ ๎‚๎‚—๎‚–๎‚‡๎‚†๎€ƒ ๎‚ˆ๎‚‘๎‚”๎€ƒ ๎‚‡๎‚ƒ๎‚…๎‚Š๎€ƒ ๎‚•๎‚–๎‚‡๎‚’๎€ƒ ๎‚„๎‚›๎€ƒ
pressing the corresponding button until its
light deactivates. Muting a step does not note:
remove the step from the sequence. The control
voltage remains present for the selected step,
and only the gate/trigger itself is muted.
Sequence direction can be changed by patch-
ing a trigger impulse into the directn input
socket . Sequence can be reset to step 1
by patching a trigger impulse into the reset
input . Sequence can be transposed (offset)
by patching a control voltage into the transp
input .
Hold step 1 and step 4 buttons simultane-
ously for 2 seconds to change whether the
gate output generates a gate or trigger im-
pulse. note: Dynamic gate width modulation
is possible because Tiranaโ€™s gate width directly
matches that of the external clock impulse.
Each step can be multiplied (repeated) up to
four times (resulting in up to 16 steps in the se-
quence). The note length is retained upon repeat.
Alternatively, each step can be divided to achieve
the popular ratcheting effect. The trigger/gate
impulse is generated 2, 3 or 4 times per note. To
program these events on a given step, enter the
step menu as follows:
module
explained
fig. 1
controls
overview
To set a desired number of repeats for a given
step, enter the divยทmlt menu by holding the
corresponding stepโ€™s button for 2 seconds. The
number of repeats is indicated by one blinking
button and three unlit buttons. Press step 2
for one repeat (2 total triggers), step 3 for
two repeats (3 total triggers), or step 4 for
three repeats (4 total triggers) of the given
step. To reset the desired step back to a single
trigger, press cancel (step 1 button). Tirana
automatically exits the divยทmlt menu mode
once a choice is made.
To set a desired number of ratchets for a given
step, enter the divยทmlt menu by pressing the
corresponding stepโ€™s button for 2 seconds. The
number of divisions is indicated by one blinking
button and three unlit buttons. Hold step 2 for
two triggers (step divided by 2), step 3 for three
triggers (step divided by 3), or step 4 for four
triggers (step divided by 4) within the given step.
fig. 2
To reset the desired step back to a single trigger,
press cancel (step 1 button). Tirana auto-
matically exits the divยทmlt menu mode once a
choice is made.
While in divยทmlt menu, a slowly-blinking button
indicates multiplication and a quickly-blinking
๎‚„๎‚—๎‚–๎‚–๎‚‘๎‚๎€ƒ๎‚‹๎‚๎‚†๎‚‹๎‚…๎‚ƒ๎‚–๎‚‡๎‚•๎€ƒ๎‚†๎‚‹๎‚˜๎‚‹๎‚•๎‚‹๎‚‘๎‚๎€ƒ๎ˆ‹๎‚•๎‚‡๎‚‡๎€ƒ๎”๎‚‹๎‚‰๎‡ค๎€ƒ๎บ๎ˆŒ๎‡ค๎€ƒ๎€„๎‚Ž๎‚Ž๎€ƒ๎‚•๎‚‡๎‚–๎‚–๎‚‹๎‚๎‚‰๎‚•๎€ƒ
are memorized and recalled after power reset.
Tirana can be set to internally divide the in-
coming clock by 2, 3 or 4. Division value can
be set by holding step buttons in the following
combinations: Buttons for division by 1+2
2. Buttons for division by 3. Buttons 1+2+3
1+2+3+4 for division by 4. note: Choosing
any of these combinations a second time sets
the module back to the default (not divided)
original clock rate. The succession is always:
orig. clock โ€”โ€บ division โ€”โ€บ orig. clock โ€”โ€บ di-
๎‚˜๎‚‹๎‚•๎‚‹๎‚‘๎‚๎‡ก๎€ƒ ๎‚‡๎‚–๎‚…๎‡ค๎€ƒ ๎€‡๎‚‹๎‚˜๎‚‹๎‚•๎‚‹๎‚‘๎‚๎€ƒ ๎‚…๎‚Š๎‚‘๎‚‹๎‚…๎‚‡๎€ƒ๎‚‹๎‚•๎€ƒ ๎‚…๎‚‘๎‚๎”๎‚‹๎‚”๎‚๎‚‡๎‚†๎€ƒ๎‚„๎‚›๎€ƒ ๎‚ƒ๎€ƒ
๎‚“๎‚—๎‚‹๎‚…๎‚๎€ƒ๎‚‰๎‚Ž๎‚‹๎‚๎‚’๎‚•๎‚‡๎€ƒ ๎‚‘๎‚ˆ๎€ƒ๎‚ƒ๎‚Ž๎‚Ž๎€ƒ ๎‚–๎‚Š๎‚‡๎€ƒ ๎‚„๎‚—๎‚–๎‚–๎‚‘๎‚๎‚•๎€ƒ ๎ˆ‹๎‚•๎‚‡๎‚‡๎€ƒ ๎”๎‚‹๎‚‰๎‡ค๎€ƒ๎บ๎ˆŒ๎‡ค๎€ƒ
All settings are memorized and recalled after
power reset.
Multiple Tirana units may be chained (using
the supplied 10-pin ribbon cable) to form a
multistep sequencer. Every module ships with
one 10-pin ribbon cable. To connect multiple
units, attach the cables exactly as shown in
๎”๎‚‹๎‚‰๎‡ค๎€ƒ๎น๎‡ค๎€ƒ๎€—๎‚Š๎‚‡๎€ƒ๎”๎‚‹๎‚”๎‚•๎‚–๎€ƒ๎‚—๎‚๎‚‹๎‚–๎€ƒ๎‚‹๎‚๎€ƒ๎‚–๎‚Š๎‚‡๎€ƒ๎‚…๎‚Š๎‚ƒ๎‚‹๎‚๎€ƒ๎‚‹๎‚•๎€ƒ๎‚–๎‚Š๎‚‡๎€ƒ๎‚๎‚ƒ๎‚•๎‚–๎‚‡๎‚”๎€ƒ
and therefore should have a jumper present
on the header. Remove the header in in
jumper from every slave unit and connect the
out header of each preceding unit to the in
header of each subsequent unit using the sup-
Stability loop cable (optional, see text)
Jumper
๎”๎‚‹๎‚‰๎‡ค๎€ƒ๎น
programming
combos
Hold any step
button for 2 seconds
to enter the step
editing menu. Slow-
ly blinking step but-
ton ( ) indicates 2-4
step repeat. Fast
blinking indicates
step ratcheting.
step 1 blinking
indicates that
neither step repeat
nor ratcheting has
been set for the
currently edited
step.
Press step 1
button to cancel
multiplication/
division on a given
step. Tirana auto-
matically exits the
step editing menu
after a choice is
made.
Press any of step
2-4 buttons to set
a multiplication
(step repeat) value.
Tirana automati-
cally exits the step
editing menu
after a choice is
made.
Hold any of step
2-4 buttons for
2 seconds to set a
division (ratchet-
ing) value. Tirana
automatically
exits the step editing
menu after a choice
is made.
Simultaneously
hold step 1+2
buttons for 2
seconds to set a
clock division by
/2. The choice will
๎‚„๎‚‡๎€ƒ๎‚…๎‚‘๎‚๎”๎‚‹๎‚”๎‚๎‚‡๎‚†๎€ƒ๎‚„๎‚›๎€ƒ๎‚ƒ๎€ƒ
glimpse of all four
buttons.
Simultaneously
hold step 1+2+3
buttons for 2
seconds to set a
clock division per
/3. The choice will
๎‚„๎‚‡๎€ƒ๎‚…๎‚‘๎‚๎”๎‚‹๎‚”๎‚๎‚‡๎‚†๎€ƒ๎‚„๎‚›๎€ƒ๎‚ƒ๎€ƒ
glimpse of all four
buttons.
Simultaneously
hold step
1+2+3+4 buttons
for 2 seconds to set
a clock division per
/4. The choice will
๎‚„๎‚‡๎€ƒ๎‚…๎‚‘๎‚๎”๎‚‹๎‚”๎‚๎‚‡๎‚†๎€ƒ๎‚„๎‚›๎€ƒ๎‚ƒ๎€ƒ
glimpse of all four
buttons.
To cancel the clock
rate division, select
any of the above
combinations a sec-
ond time. To make
๎‚ƒ๎‚๎‚‘๎‚–๎‚Š๎‚‡๎‚”๎€ƒ๎‚…๎‚Š๎‚‘๎‚‹๎‚…๎‚‡๎‡ก๎€ƒ๎”๎‚‹๎‚”๎‚•๎‚–๎€ƒ
cancel the previous
one, then select a
new choice.
Simultaneously
hold step 1+4
buttons for 2 secs
to toggle between
trigger and gate
mode. The choice
๎‚™๎‚‹๎‚Ž๎‚Ž๎€ƒ๎‚„๎‚‡๎€ƒ๎‚…๎‚‘๎‚๎”๎‚‹๎‚”๎‚๎‚‡๎‚†๎€ƒ
by a glimpse of all
the buttons.
๎”๎‚‹๎‚‰๎‡ค๎€ƒ๎บ
plied 10-pin ribbon cable(s). Use only note:
the master unitโ€™s sockets for patching.
Older Tirana revisions can be chained to newer
revisions as long as the rev. II unit is the master.
๎€—๎‚‘๎€ƒ๎‚…๎‚Š๎‚ƒ๎‚‹๎‚๎‡ก๎€ƒ๎”๎‚‹๎‚”๎‚•๎‚–๎€ƒ๎‚—๎‚’๎‚†๎‚ƒ๎‚–๎‚‡๎€ƒ๎‚–๎‚Š๎‚‡๎€ƒ๎‚‘๎‚Ž๎‚†๎‚‡๎‚”๎€ƒ๎‚—๎‚๎‚‹๎‚–๎ˆ‹๎‚•๎ˆŒ๎€ƒ๎‚–๎‚‘๎€ƒ๎‚–๎‚Š๎‚‡๎€ƒ๎‚Ž๎‚ƒ๎‚–-
๎‚‡๎‚•๎‚–๎€ƒ๎”๎‚‹๎‚”๎‚๎‚™๎‚ƒ๎‚”๎‚‡๎‡ก๎€ƒ๎‚–๎‚Š๎‚‡๎‚๎‡ก๎€ƒ๎‚…๎‚‘๎‚๎‚๎‚‡๎‚…๎‚–๎€ƒ๎‚–๎‚Š๎‚‡๎€ƒ๎‚—๎‚๎‚‹๎‚–๎‚•๎€ƒ๎‚ƒ๎‚•๎€ƒ๎‚•๎‚Š๎‚‘๎‚™๎‚๎€ƒ๎‚‹๎‚๎€ƒ
๎”๎‚‹๎‚‰๎‡ค๎€ƒ๎น๎€ƒ๎‚๎‚ƒ๎‚๎‚‹๎‚๎‚‰๎€ƒ๎‚•๎‚—๎‚”๎‚‡๎€ƒ๎‚–๎‚‘๎€ƒ๎‚—๎‚•๎‚‡๎€ƒ๎‚–๎‚Š๎‚‡๎€ƒ๎ท๎‡ฆ๎‚’๎‚‹๎‚๎€ƒ๎‚•๎‚–๎‚ƒ๎‚„๎‚‹๎‚Ž๎‚‹๎‚–๎‚›๎€ƒ๎‚Ž๎‚‘๎‚‘๎‚’๎€ƒ
cable that shipped with the original Tirana.
Tirana has four user-selectable latency values
which can be adjusted to accommodate any
timing inaccuracies between clock and reset im-
๎‚’๎‚—๎‚Ž๎‚•๎‚‡๎‚•๎‡ค๎€ƒ๎€—๎‚‘๎€ƒ๎‚•๎‚‡๎‚Ž๎‚‡๎‚…๎‚–๎€ƒ๎‚ƒ๎€ƒ๎‚๎‚‡๎‚™๎€ƒ๎‚˜๎‚ƒ๎‚Ž๎‚—๎‚‡๎‡ก๎€ƒ๎”๎‚‹๎‚”๎‚•๎‚–๎€ƒ๎‚๎‚ƒ๎‚๎‚‡๎€ƒ๎‚•๎‚—๎‚”๎‚‡๎€ƒ๎‚–๎‚Š๎‚‡๎€ƒ
module is not chained with other Tiranas and
disconnect the chaining cable (not the power
cable) if necessary. Then, during system pow-
er up, hold the button to enter factory step 1
maintenance mode as indicated by all buttons
slowly blinking. Next, select the step 1 button
for 0.35ms of latency; button for 0.7ms; step 2
step 3 step 4 button for 1.4ms (default); for
๎ธ๎‡ค๎พ๎‚๎‚•๎‡ค๎€ƒ ๎€๎‚ƒ๎‚–๎‚‡๎‚๎‚…๎‚›๎€ƒ ๎‚…๎‚Š๎‚‘๎‚‹๎‚…๎‚‡๎€ƒ ๎‚…๎‚ƒ๎‚๎€ƒ ๎‚„๎‚‡๎€ƒ ๎‚…๎‚‘๎‚๎”๎‚‹๎‚”๎‚๎‚‡๎‚†๎€ƒ ๎‚„๎‚›๎€ƒ ๎‚ƒ๎€ƒ
quick glimpse of the selected button. All settings
๎‚ƒ๎‚”๎‚‡๎€ƒ๎‚๎‚‡๎‚๎‚‘๎‚”๎‚‹๎‚œ๎‚‡๎‚†๎€ƒ๎‚ƒ๎‚๎‚†๎€ƒ๎‚”๎‚‡๎‚…๎‚ƒ๎‚Ž๎‚Ž๎‚‡๎‚†๎€ƒ๎‚ƒ๎‚ˆ๎‚–๎‚‡๎‚”๎€ƒ๎‚’๎‚‘๎‚™๎‚‡๎‚”๎€ƒ๎‚”๎‚‡๎‚•๎‚‡๎‚–๎‡ค๎€ƒ๎ˆˆ
step multiplication & division
clock division gate vs. trigger
Four CV/gate
steps
Per-step repeti-
tion or ratcheting
Per-step gate
muting
Accepts clock
rates up to 320Hz
On-board clock
divider
Voltage controlled
play direction,
transposition,
and reset
Unipolar and
bipolar adjustable
voltage range
Expandable by
chaining more
Tirana units
Eurorack synth
compatible
6hp, skiff friendly
Current draw:
+30mA / โ€“5mA
Reverse power
protection

Especificaciones del producto

Marca: Xaoc
Categorรญa: No categorizado
Modelo: Tirana II

ยฟNecesitas ayuda?

Si necesitas ayuda con Xaoc Tirana II haz una pregunta a continuaciรณn y otros usuarios te responderรกn




No categorizado Xaoc Manuales

Xaoc

Xaoc Batumi Manual de Usario

4 Septiembre 2024
Xaoc

Xaoc Poti Manual de Usario

4 Septiembre 2024
Xaoc

Xaoc Zadar Manual de Usario

4 Septiembre 2024
Xaoc

Xaoc Katowice Manual de Usario

4 Septiembre 2024
Xaoc

Xaoc Tirana Manual de Usario

4 Septiembre 2024
Xaoc

Xaoc Warna II Manual de Usario

4 Septiembre 2024
Xaoc

Xaoc DEVA Manual de Usario

4 Septiembre 2024
Xaoc

Xaoc Lipsk Manual de Usario

4 Septiembre 2024
Xaoc

Xaoc Praga Manual de Usario

4 Septiembre 2024

No categorizado Manuales

รšltimos No categorizado Manuales