Blebox airSensor Manual de Usario

Blebox Equipo de medición airSensor

Lee a continuación 📖 el manual en español para Blebox airSensor (2 páginas) en la categoría Equipo de medición. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

setting of the WiFi network and nd the network named „airSensor

-xxxxxxxxxx” where xxxxxxxxxx is the serial number of the device. Connect to

this network.

Turn on the wBox application. A device will appear at the top of the screen. To

add it to the application, click on "+" on the right side of the name. To pre-

congure the controller, click on the default device name.

Download the . If you have an Android mobile device, free wBox application

you will nd the application in the Play Store. For iOS devices the application

is in the App Store.

By using your mobile phone or tablet, connect it to the device wireless

network. To do this, enter to your smartphone or tablet settings, then go to

2FIRST START

The main controller screen shows current information from the air quality

sensor. Air quality is determined based on the measurement of particulate

matter concentrations PM2.5 and PM10 and is shown the worst value of both.

The current state of air quality is displayed in the upper part of the screen in

a colored icon and also in word status, and is signaled by colored LEDs built

into the device and it shows in the following way:

At the bottom of the screen there is a table with numerical values of particula-

te matter concentrations. Fields with concentration values PM2.5 and PM10

change its color in relation to the degree of exceeding the standard in the

color scale presented before, moreover, the percentage value in relation to the

value of the standard is presented in brackets. For example, a reading (50%)

means that the current air pollution concentrations is only half of the accepta-

ble value, while the indication (300%) means a 3-fold exceedance of the

standard. Next to the percentage, the change trend is also calculated,

compared to the average of the last hour of measurements. The trend is

indicated by an up, down arrow or a horizontal line in the case that no changes

have been registered, it is only displayed after the sensor's working one hour.

At the very bottom of the screen is presented the status of measurements on

the device. "Last measurement" means that the device displays a measure-

ment taken within a time not exceeding 10 minutes. The device automatically

performs another measurement every 10 minutes and displays the last air

pollution concentrations value. This behavior is dictated by the care of the

sensor's lifetime due to the fact the air pollution slowly changes over the time.

It is also possible to manually force the measurement. To do this, press the

"Refresh" icon (two arrows) in the upper right part of the screen. Within the

rst 20 seconds shows the status "Measurement in progress", which next will

be change to "Current measurement" and the concentration values will be

updated. To switch the device into continuous measurement mode, in which

measurements are taken every 1 second, hold down the "Refresh" icon for

over 3 seconds. The icon background will turn gray and the device will start

a continuous measurement, the device will start the continuous measure-

ment, which will last until the moment it returns to the main screen of the

application or the browser page is closed. Leaving the device in continuous

measurement mode, should remember about the lifetime of the measuring

system, estimated at approx. 8000 hours.

Historical measurement data are only available for sensors mounted outside,

congured in remote access mode, with a correctly set location. They are

presented on the map available on blebox.eu

very good (intense green color)

good (light green)

moderate (light yellow)

sucient (orange color)

bad (bright red)

very bad (intensive red)

3MEASURING DATA

You can also set the conguration using the web browser of

your phone/tablet. After connecting to the wireless

network of the controller, turn on the browser and go to:

www.blebox.eu

SAFETY RULES

Improper connections may be dangerous, it can damage the

controller, and loss of the warranty.

The installation of the device to a power mains that does not

meet the quality requirements dened by EN 50081-1, EN

50082-1, UL508, EN 60950, will result in the loss of the warranty.

DANGER! Risk of electric shock! Even with the device turned o,

the outputs may be live. All assembly work should be ALWAYS

performed with the disconnected power circuit.

YOUR PERSONAL AIR QUALITY SENSOR - BREATHE AWARENESS

Disconnect supply voltage circuit before installing the controller. Remember

that any mounting works should be carried out when the main voltage is

disconnected (switch o the mains fuse or disconnecting the power supply

from the socket).

The device should be mounted in a place protected from direct adverse

environmental conditions, in particular atmospheric precipitation. At the

same time, should be paid attention to ensuring a good air exchange around

the device. Remember that metallic elements (wires, housing parts) have

a negative inuence on the range of the device, and consequently the

comfort of use. It is recommended that the device be mounted in a stable and

xed position, correctly oriented (according to the inscriptions on the casing),

fastened with screws, wall plugs or by means of a double-sided assembly

tape.

Remove the cover of the device by lifting it. Choose a power supply - a 5V USB

connector located on the left side of the device or a 12-24V AC / DC mains

adapter connected via wires to a plug-in connector located in the right part of

the PCB (polarization is irrelevant). Connect the power wire to the USB

connector or plug-in connector. Bringing in the power wire outside the

housing through the aperture in the inferior part, replace the housing.

Turn on the device by switching on the power supply voltage (switching on

the main power supply circuit fuse or connecting the power supply to the

socket). The device will turn on the LEDs on white color for a few seconds and

then will change into a color depending on the air quality. Continuous

lighting in white color indicates the sensor error, which is also signaled by the

red status visible in the wBox application (more information about the wBox

application later in the manual). In this case, check the wire connected to the

sensor circuit board.

1INSTALLATION - BASICS

air quality sensor

with μWiFi technology

WARNING!

Never connect at the same time power to the USB

connector and to the plug-in connector. It may cause

damage to the device.

very good

good

moderate

sucient

bad

very bad

ADDITIONAL INFORMATION

SOFTWARE UPDATE

LOCATION AND TIME OF THE DEVICE,

SCHEDULE

To update the software in the controller, connect it to your home WiFi network

(see "Access Point and WiFi settings" section) which is connected to the

Internet. Go to “Settings” (icon at the top-right corner of the screen) and click

the "Get new rmware" button in the nal section on settings. Wait about 1

minute, do not close the interface and don’t perform other actions. The device

will download the latest software. The software version number, hardware

version and device identier can be read at the bottom of the settings screen.

To be able to use historical air quality data, it is necessary to set the clock and

location of the device. Go to the "Device time" section of the settings and then

click "Change zone". Select your region and locations from the list, conrming

your selection with the "Save" button. The device will synchronize its time with

the time server (if the controller is in a WiFi network with Internet access) or it

will download time from the phone/tablet.

Next, in the "Device location" section, click "Set locations". The application /

browser will ask whether to share locations - allow. In the "Coordinates" eld,

the approximate coordinates of your location should appear. If the "Set

locations" button blinks red with the word "error" or the "Coordinates" eld

did not change the value from "Not set" to numeric data, a failure occurred in

the location download. You should then make sure that the phone / tablet has

a GPS module and that the location sharing support is enabled on the phone.

TECHNICAL SPECIFICATIONS

power supply 12..24V AC / DC through a plug-in

conector or 5V via micro USB connector

PM1: 0,3..1,0 μm, PM2.5: 1,0..2,5 μm,

PM10: 2,5..10 μm

particulate matter

classication

direct connection (as Access Point),

Wi-Fi connection via a standard router,

connection with access from any location

in the world (requires only access to the Internet)

mode

measurement precision

API

compatible devices

50% for particles with a size of 0,3 μm,

98% for size particles >=0,5 μm

open

Apple iPhone, Apple iPad, iPad Mini,

Android, computers and mobile devices

supporting HTML5

type of air quality

indication

numeric and graphic indicator in wBox

application, changing LED colors

bi-directional, encryptedtransmission type

μWiFi, compatible with WiFi, 802.11g

communication standard

every 10 minut or on demand

frequency

of the measurement

laser, PMS5003type of sensor

71 x 71 x 27 mmdimensions

mounting screws, wall plug or double-sided

adhesive tape

protection level IP32, mounting in a place protected

from rain

radio frequency 2.4 GHz

ACCESS POINT AND WIFI NETWORK SETTINGS

Go to "Connect to WiFi network" section, where you can connect the device to

the WiFi home network to be able to connect to it via it or from anyplace in the

world. To do this, select the network name from the list and press "Connect".

If required, enter the WiFi network password. When connecting the device to

the home network, the phone / tablet may be disconnected from the device's

network.

After completing the WiFi network conguration, you can disconnect from

the device network and connect the phone / tablet directly to your home WiFi

network. Control from the wBox application will work in the same way as

when the phone / tablet is connected to the device's network. If as a user you

leave the local network, eg leaving your home or enclosing mobile data, the

wBox application will signal this status as "Remote mode". In this case, you will

have access to the device data, but for security reasons settings options will

not be available.

In the "Access point settings" section, you can change the name and give the

password of the WiFi network emitted by the device. Remember that

changing the network name or password can cause disconnection with the

device immediately after clicking the "Save" button, so you should reconnect

to the WiFi network.

Go to „Settings” (icon in the upper right corner of the screen). In the "Main

settings" section, you can change the device name which is visible in the wBox

application. The option "Signal LED on" allows you to turn on the LEDs built

into the device.

In order to communicate with a device being out of the local WiFi network,

from anyplace in the World, via wBox applications, must be set to "Yes" the

option "Enable remote access". Setting this option to "Yes" also means giving

consent for the sending of the measurement data to a public map of the air

pollution available on the web page blebox.eu and the archiving of this data

together with its location. Setting the "No" option will result in the lack of the

access to the controller when it is out of the local network and the lack of

access to historical data - only the current values will be visible.

In the "Sensor settings" section, select the place of its installation - outside or

inside the building (measurement of indoor air quality).

4DEVICE SETTINGS

for more information visit our website

www.blebox.eu

or send us an email to: info@blebox.eu

support is available at support@blebox.eu

Especificaciones del producto

Marca:	Blebox
Categoría:	Equipo de medición
Modelo:	airSensor

¿Necesitas ayuda?

Si necesitas ayuda con Blebox airSensor haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

Equipo de medición Blebox Manuales

Blebox airSensor Manual de Usario

11 Septiembre 2024

Equipo de medición Manuales

Últimos Equipo de medición Manuales

PeakTech 1207 Manual de Usario

26 Octubre 2024

Kern FL 1KG Manual de Usario

25 Octubre 2024

PeakTech 6193 Manual de Usario

25 Octubre 2024

PCE Instruments PCE-TUM 50 Manual de Usario

24 Octubre 2024

PCE Instruments PCE-325D Manual de Usario

23 Octubre 2024

PCE Instruments PCE-AM 30 Manual de Usario

23 Octubre 2024

PCE Instruments PCE-900 Manual de Usario

23 Octubre 2024

PCE Instruments PCE-CSM 10 Manual de Usario

23 Octubre 2024

PCE Instruments PCE-CSM 7 Manual de Usario

23 Octubre 2024

PCE Instruments PCE-CSM 3 Manual de Usario

23 Octubre 2024