CyberData Systems SIP-enabled VoIP V3 Manual de Usario

CyberData Systems sistema de intercomunicación SIP-enabled VoIP V3

Lee a continuación 📖 el manual en español para CyberData Systems SIP-enabled VoIP V3 (4 páginas) en la categoría sistema de intercomunicación. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/4

Quick Start Guide 930503A

1.0 Out-of-Box and Prior to Final Installation

1.1. Verify that you have received all of the parts listed on the Installation Quick

Reference placemat.

1.2. Download the current manual, otherwise known as an Operation Guide,

which is available on the Documentation page at the following website

address:

http://www.cyberdata.net/products/voip/digitalanalog/intercomemergency/docs.html

Note You can also navigate to the Documentation page by going to

www.CyberData.net and following the steps that are indicated by

the following figures:

2.0 Select Power Source

PoE Switch PoE Injector

Set PoE power type to Class 0 = 13W CAT6 cable recommended—

for longer distances

Be sure you are using a non-PoE switch or port

Make sure port is not in trunk mode

Set port to full duplex/ 100mbps

Spanning Tree Protocol (STP) must be disabled or Portfast enabled

VoIP Emergency Intercom

Quick Start Guide

The IP Endpoint Company

Quick Start Guide 930503A

3.0 Power Test

3.1. Plug in the CyberData device and monitor the LED activity above the

ethernet port on the back of the Intercom. See the following figure:

3.2. The GREEN Link LED blinks off once during the boot up process and then

comes on again and remains constant (solid GREEN). The YELLOW

Activity LED may be blinking depending on the network activity.

During the initialization process, the GREEN Call Button LED should come

on and be constant (solid GREEN). After the Intercom has completed

booting, the LED will blink twice and then remain constant thereafter.

Normally, this process will take about 30 seconds. However, if no DHCP1 is

available, then this process could take up to 2 minutes.

3.3. When the Intercom has completed the initialization process, press and hold

the RTFM switch (SW1 button) for 3 seconds to announce the IP address.

This concludes the power test. Go to Section 4.0, "Connecting to a Network

in a Test Environment".

1. This only applies to firmware versions 6.x.x and later. For versions 5.1.2 and

earlier, the default static IP address is 10.10.10.10.

Link LED

Activity LED

Quick Start Guide 930503A

4.0 Connecting to a Network in a Test Environment

Note The following connections are usually needed for this procedure:

• PC

• PoE switch or injector

• CyberData device

4.1. In a test environment, use a PC that is connected to the same switch as a

single CyberData device. Note the subnet of the test PC.

4.2. Use the CyberData Discovery Utility program to locate the device on the

network. You can download the Discovery Utility program from the

following website address:

http://www.cyberdata.net/support/voip/discovery_utility.html

4.3. Wait for initialization to complete before using the Discovery Utility

program to scan for a device. The device will show the current IP address,

MAC address, and serial number.

4.4. Select the device.

Note If the IP address of the device is in the same subnet of the PC, then

go to Step 4.7.

4.5. If the IP address of the device is different from the subnet of the PC, then

complete the following steps:

4.5.1. Click the Details tab.

4.5.2. Click Adv. Config to manually configure settings with an available IP

address in the same subnet.

Note A gateway address of 0.0.0.0 or a subnet address of

255.255.255.255 will prompt you to enter a valid address.

4.5.3. Click OK after you are finished making changes.

4.6. A dialog box will prompt you to click OK after confirming the configuration

changes and will ask you to wait while the device reboots. Please wait for

the device to power up and wait for the Discovery Utility program to find

the device on the network.

Especificaciones del producto

Marca:	CyberData Systems
Categoría:	sistema de intercomunicación
Modelo:	SIP-enabled VoIP V3

¿Necesitas ayuda?

Si necesitas ayuda con CyberData Systems SIP-enabled VoIP V3 haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

sistema de intercomunicación CyberData Systems Manuales

CyberData Systems 011491 Manual de Usario

13 Septiembre 2024

CyberData Systems SIP Talk-Back Manual de Usario

13 Septiembre 2024

CyberData Systems SIP-enabled VoIP V3 Manual de Usario

13 Septiembre 2024

CyberData Systems V3 SIP-enabled IP Manual de Usario

12 Septiembre 2024

CyberData Systems SIP-enabled IP V3 Manual de Usario

12 Septiembre 2024

sistema de intercomunicación Manuales

Últimos sistema de intercomunicación Manuales

Extel Levo JS-V742N2 Manual de Usario

27 Octubre 2024

Dahua Technology DHI-VTH5221DW-S Manual de Usario

26 Octubre 2024

Hikvision DS-KIS703-P Manual de Usario

8 Octubre 2024

Viking K-1900-712L-EWP Manual de Usario

1 Octubre 2024

Viking K-1700-3 Manual de Usario

1 Octubre 2024

Viking E-50-SS Manual de Usario

1 Octubre 2024

Viking E-50-WH Manual de Usario

1 Octubre 2024

Viking K-1700-IP-EWP Manual de Usario

1 Octubre 2024

Viking E-60-BN Manual de Usario

1 Octubre 2024

Viking E-1600-53-IP Manual de Usario

1 Octubre 2024