EMOS E8236 Manual de Usario

Lee a continuación 📖 el manual en español para EMOS E8236 (48 páginas) en la categoría Estación meteorológica. Esta guía fue útil para 12 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/48
E8236
GB Wireless weather station
CZ Bezdrátová meteostanice
SK Bezdrôtová meteostanica
PL Bezprzewodowa stacja meteorologiczna
HU Vezeték nélli meteorológiai állomás
SI
Brezžična meteorološka postaja
RS HR| |BA Bežična meteorološka stanica
DE Funk-Wetterstation
UA Вездротова метеостанція
RO Stație meteo fără r
LT Belaidė meteorologinė stotelė
LV Bezvadu meteoroloģiskā stacija
2606149000_31-E8236 148 × 210 mm
www.emos.eu
2
GB Wireless weather station
Specications:
radio controlled clock
indoor temperature: -10 °C to +50 °C
outdoor temperature: -40 °C to +60 °C
temperature resolution: 0.1 °C
temperature measurement accuracy: ±1 °C (20 to 24 °C), otherwise ±2 °C
wireless sensor: transmission frequency 433 MHz
radio signal range: up to 35 m in an open area
number of sensors per connection: max. 3
indoor and outdoor relative humidity: 20 % to 95 %
resolution: 1 %
measurement accuracy: ±5 % (30 to 80 %), otherwise ±8 %
bar. pressure measurement range: 800 hPa to 1 100 hPa
power supply:
main unit: 2× 1.5 V AAA batteries (not supplied)
sensor: 2× 1.5 V AA batteries (not supplied)
dimensions and weight without batteries:
main unit: 110 × 110 × 47 mm, 125 g
sensor: 91 × 60 × 28 mm, 39 g
Display Description
1
2 3
4
5
6
78
9
10
11
16
15
14
13
12
1. Indoor temperature
2. Weather forecast icon
3. MAX/MIN measured values
4. Outdoor temperature
5. Pressure trend
6. Outdoor humidity
7. Signal reception from sensor icon
8. Glaze ice icon
9. Sensor number
10. Alarm icon
11. Current time
12. DCF signal reception icon
13. DST icon
14. Date/pressure
15. Sensor battery at icon
16. Indoor humidity
Back
1
2
4
3
1. Speaker
2. Weather station control buttons (MODE, UP/CH,
DOWN/CF/WAVE, MEM/HPA, AL ON/OFF, SNZ/LIGHT)
3. Stand
4. Battery compartment
Getting Started
First insert batteries into the main unit, then into the wireless sensor. Do not combine old and new or various kinds of batteries
(alkaline, carbon-zinc and nickel-cadmium); do not use rechargeable batteries!
3
Follow these steps:
1. Open the cover at the rear of the station and the rear of the sensor.
2. Insert 2 1.5 V batteries type AAA for the weather station and close the cover. Then insert 2 1.5 V batteries type AA into the
sensor. Make sure to observe the correct polarity of the batteries according to the drawing at the bottom of the battery
compartment!
3. Outdoor temperature will be displayed on the weather station within 2 minutes. If outdoor temperature is not displayed,
remove the batteries from the sensor and reinsert them or long-press the TX button under the battery cover of the sensor
to again send signal from the sensor to the weather station.
4. Close the sensor cover and place the sensor outside on a dry, shaded place. We recommend placing the sensor on the north
side of the house. The range of the sensor may decrease substantially in areas with large number of obstacles.
5. The sensor is resistant to dripping water; however, it should not be exposed to sustained rain.
6. Do not place the sensor on metal objects; doing so will reduce the transmission range.
Switching Over to Another Channel and Connecting Additional Sensors
(The following procedure for connecting additional sensors is for a replacement sensor E05018. It does not apply to the sensor included
in the package).
1. Select the desired sensor channel number – 1, 2 or 3 – by pressing the CH button at the rear of the weather station. Then
press and hold the CH button, the icon will start ashing.
2. Remove the cover from the battery compartment and insert batteries (2× 1.5 V AAA).
3. Use the CH button to set the desired sensor channel number 1, 2, 3 which will be shown on the front panel display.
Data from the sensor will be loaded within 3 minutes.
4. If the sensor signal is not detected, remove the batteries, reinsert them and repeat the process.
Synchronisation of Lost Temperature Signal
In case the weather station is not showing data from the outdoor sensor, check:
Distance of the station or sensor from sources of interference such as computer monitors or TV sets. It should be at least
2 meters.
Whether the weather station or sensor is not in the proximity of metal objects and frames (such as window frames).
Whether the weather station functionality is not aected by other devices using a similar frequency (wireless headphones,
wireless blinds control, gate control, garage door control etc.), or wireless devices used in the immediate neighbourhood.
Maximum range of the wireless sensor is 35 m in an open area. The range depends on local conditions and the construction
materials of buildings.
Transmission is also aected by interferences in the area. If reception fails, try to restore functionality by removing the batteries.
If there is interference to radio or television reception caused by the devices transmission, this can be removed by one of the
following measures:
Reorient or relocate the antenna
Increase the distance between the device and the receiver
Consult with your dealer or an authorized service
The inuence of ambient radio interference may result in poor data display.
Radio Controlled Clock – DCF77
The radio controlled clock provides the most accurate time on the European continent. The radio signal propagates via radio
waves (77.5 kHz) from a site near Frankfurt on the Main in Germany within a range of 1 500 km. This radio time signal automat-
ically takes into account summer (DST) and winter time, leap years and date changes. In standard conditions (at safe distance
from sources of interference, such as TV sets, computer monitors), the reception of time signal takes several minutes. If the clock
does not detect the signal, follow these steps:
1. Move the weather station to another location and try to detect the DCF signal again.
2. Make sure the distance of the clock from sources of interference, such as computer monitors or television sets, is at least
1.5 to 2 meters when receiving this signal. When receiving DCF signal, do not put the weather station in the proximity of
metal doors, window frames and other metal structures or objects (washing machines, dryers, refrigerators etc.).
3. In reinforced concrete structures (cellars, high-rise buildings etc.), the DCF signal reception is weaker, depending on the
conditions. In extreme cases, place the weather station close to a window toward the transmitter.
The reception of the DCF77 radio signal is aected by the following factors:
thick walls and insulation, basements and cellars
inadequate local geographical conditions (these are dicult to assess in advance)
atmospheric disturbances, thunderstorms
appliances with no interference elimination
television sets and computers placed near the DCF receiver
DCF Signal Reception
If the batteries in the weather station are suciently charged, DCF signal reception and time setting will occur automatically.
The weather station will begin automatically searching for DCF signal 3 minutes after the insertion of batteries. The search for
signal takes 7 minutes. The icon will be ashing. If the station successfully detects DCF signal, the correct time and date will
be set and the icon will remain on the screen. If the station fails to detect DCF signal, you can activate the search manually
by pressing and holding the WAVE button. If you wish to cancel the manual search mode, again press and hold the WAVE button.

Especificaciones del producto

Marca: EMOS
Categoría: Estación meteorológica
Modelo: E8236

¿Necesitas ayuda?

Si necesitas ayuda con EMOS E8236 haz una pregunta a continuación y otros usuarios te responderán




Estación meteorológica EMOS Manuales

Estación meteorológica Manuales

Últimos Estación meteorológica Manuales