Hatco CWBR-4 Manual de Usario

Hatco Refrigerador CWBR-4

Lee a continuación 📖 el manual en español para Hatco CWBR-4 (7 páginas) en la categoría Refrigerador. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/7
P/N 07.04.609.00 © 2020 Hatco Corporation
Remote Refrigerated Drop-In Wells
Cuves réfrigérées de libre-service
contrôlées à distance Hatco
CWBR, CWBR-S, CWBX, CWBX-S Series/Série
Installation and Operating Manual
Manuel d’installation et d’utilisation
hatcocorp.com
Register Online!
(see page 2)
S’inscrire en ligne!
(voir page 18)
Do not operate this equipment unless you
have read and understood the contents
of this manual! Failure to follow the
instructions contained in this manual
may result in serious injury or death.
This manual contains important safety
information concerning the maintenance,
use, and operation of this product. If
you’re unable to understand the contents
of this manual, please bring it to the
attention of your supervisor. Keep this
manual in a safe location for future
reference.
English = p 2
WARNING
No opere este equipo al menos que haya
leído y comprendido el contenido de este
manual! Cualquier falla en el seguimiento
de las instrucciones contenidas en
este manual puede resultar en un serio
lesión o muerte. Este manual contiene
importante información sobre seguridad
concerniente al mantenimiento, uso y
operación de este producto. Si usted
no puede entender el contenido de
este manual por favor pregunte a su
supervisor. Almacenar este manual en
una localización segura para la referencia
futura.
ADVERTENCIA
Ne pas utiliser cet équipement sans avoir
lu et compris le contenu de ce manuel ! Le
non-respect des instructions contenues
dans ce manuel peut entraîner de
graves blessures ou la mort. Ce manuel
contient des informations importantes
concernant l’entretien, l’utilisation et le
fonctionnement de ce produit. Si vous ne
comprenez pas le contenu de ce manuel,
veuillez le signaler à votre supérieur.
Conservez ce manuel dans un endroit
sûr pour pouvoir vous y référer plus tard.
Français = p 18
AVERTISSEMENT
8Form No. CWBRM-0220
English
Line Size* Load
Model Suction Liquid BTU/Hour
CWBX-1
3/8 1/4″ ″
330
CWBX-2 630
CWBX-3 930
CWBX-4 1230
CWBX-5 1530
CWBX-6 1830
Compressor Specifications — CWBX
* Recommended line size for installations of 50’ or less.
Line Size* Load
Model Suction Liquid BTU/Hour
CWBX-S1
3/8 1/4″ ″
330
CWBX-S2 730
CWBX-S3 1130
CWBX-S4 1530
Compressor Specifications — CWBX-S
* Recommended line size for installations of 50’ or less.
SPECIFICATIONS
Discharge
Pressure
Suction
Pressure Superheat Subcooling
115 to 125 psig
(7.9 to 8.6 bar)
6 to 9 psig
(0.4 to 0.6 bar)
4° to 10°F
(2.2° to 5.6°C)
5° to 10°F
(2.8° to 5.6°C)
Operating Specifications
Remote Unit Fill Weights
NOTE: The Operating Specifications are accurate for units in an ambient
air temperature of 75°F (24°C).
Models Fill Weights
CWBR-1, CWBR-4
CWBR-S1, CWBR-S3 1 lb 15 oz
CWBR-2, CWBR-3
CWBR-S2 2 lbs 1 oz
CWBR-5, CWBR-6
CWBR-S4 2 lbs 13 oz
Form No. CWBRM-0220 13
English
OPERATION
Changing the Setpoint Temperature
Use the following procedure to change the setpoint temperature
on the digital temperature controller.
NOTE: Changes to the setpoint temperature should be made
in small increments (1 to 2 degrees). Wait at least two
hours after a change in setpoint temperature before
checking for the desired result.
1. Press and hold the key for one second until the
display flashes the current setpoint temperature.
2. Press the or key to increase or decrease the
setpoint temperature. If no key is pressed within 60
seconds, the display will revert to normal operation and
the current temperature of the unit will be shown on the
display.
3. Press the key to lock in the new setpoint temperature.
The display will revert to show the current temperature of
the unit.
Display
Down Arrow/
Defrost Key
Unit
“Active”
Symbol
Up Arrow/
Standby Key SET
Key
Digital Temperature Controller
NOTE: If the display flashes “OFF” and then the current
temperature, press and hold the key for three
seconds. The display will no longer flash “OFF”.
If the display flashes “df” and then the current
temperature, press and hold the key for three
seconds. The display will no longer flash “df”.
Setting the Auto-Defrost Cycle
Hatco Refrigerated Wells are programmed at the factory with
the auto-defrost cycle deactivated. Use the following procedure
to activate the auto-defrost cycle if ambient or operational
conditions require the unit to defrost occasionally. When the
unit is in a defrost cycle, will appear on the display.
1. Press and hold the key for three seconds to access
programming mode. “PS” (password) will appear on the
display.
2. Press the key again. A numeric value will appear on
the display.
3. Press the or key until the number “22” appears
on the display, then press the key.
4. Use the or key to scroll through the programmable
parameters until “dI” (defrost interval) appears on the display.
5. Press the key to select “dI”. The current number of
defrost cycles will be shown on the display. For new units,
this value will be “0”.
6. Press the or key within 60 seconds to scroll to
the desired number of hours between defrost cycles. See
below for examples of how the defrost cycle(s) operate:
“0” = auto-defrost is deactivated
“1” = unit will defrost every hour
“4” = unit will defrost every four hours
“12” = unit will defrost every twelve hours
If no key is pressed within 60 seconds, the display will
revert to normal operation and the current temperature of
the unit will be shown on the display.
7. Press the key to lock in the new defrost cycle setting.
8. Press and hold the key for three seconds to exit
programming mode. The display will revert to show the
current temperature of the unit.
Changing Fahrenheit and Celsius Setting
Use the following procedure to change between Fahrenheit and
Celsius on the display.
1. Press and hold the key for three seconds to access
programming mode. “PS” (password) will appear on the
display.
2. Press the key again. A numeric value will appear on
the display.
3. Press the or key until the number “22” appears
on the display, then press the key.
4. Use the key to scroll through the programmable or
parameters until appears on the display.
5. Press the key to select .
6. Press the or key within 60 seconds to scroll to
the desired setting. See below for the correct setting:
“0” = Displays Celsius
“1” = Displays Fahrenheit
If no key is pressed within 60 seconds, the display will
revert to normal operation and the current temperature of
the unit will be shown on the display.
7. Press the key to lock in the new setting.
8. Press and hold the key for three seconds to exit
programming mode. The display will revert to show the
current temperature of the unit.

Especificaciones del producto

Marca: Hatco
Categoría: Refrigerador
Modelo: CWBR-4

¿Necesitas ayuda?

Si necesitas ayuda con Hatco CWBR-4 haz una pregunta a continuación y otros usuarios te responderán


Refrigerador Hatco Manuales

Hatco

Hatco CWB-S4 Manual de Usario

1 Septiembre 2024
Hatco

Hatco CWBR-4 Manual de Usario

1 Septiembre 2024
Hatco

Hatco CWBR-3 Manual de Usario

1 Septiembre 2024
Hatco

Hatco CWB-S3 Manual de Usario

1 Septiembre 2024
Hatco

Hatco IWB-S3 Manual de Usario

1 Septiembre 2024
Hatco

Hatco CWBR-S3 Manual de Usario

1 Septiembre 2024
Hatco

Hatco CWBX-3 Manual de Usario

1 Septiembre 2024

Refrigerador Manuales

Últimos Refrigerador Manuales

GE

GE Profile Performance TPX24PBDCC Manual de Usario

27 Octubre 2024
Kenmore

Kenmore 795.74019 Manual de Usario

27 Octubre 2024
Kolpak

Kolpak Polar Pak QS6-068-CT Manual de Usario

27 Octubre 2024
Hotpoint

Hotpoint LH8 FF2I X Manual de Usario

27 Octubre 2024
Amana

Amana SX522 Manual de Usario

27 Octubre 2024
LG

LG GMB844PZFG Manual de Usario

27 Octubre 2024
Scancool

Scancool SFS170 Manual de Usario

27 Octubre 2024
Hoover

Hoover HCA 390 FFK Manual de Usario

27 Octubre 2024
Junker

Junker JC30GCSE0 Manual de Usario

27 Octubre 2024
Orima

Orima ORS 457 NF X Manual de Usario

27 Octubre 2024