Kenwood CMOS-230 Manual de Usario
Kenwood
cámara de coche
CMOS-230
Lee a continuación 📖 el manual en español para Kenwood CMOS-230 (52 páginas) en la categoría cámara de coche. Esta guía fue útil para 12 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/52
CMOS-230
UNIVERSAL REAR VIEW CAMERA
INSTRUCTION MANUAL
CAMÉRA DE RECUL UNIVERSELLE
MODE D’EMPLOI
UNIVERSAL RÜCKFAHRKAMERA
BEDIENUNGSANLEITUNG
UNIVERSELE ACHTERUITRIJCAMERA
GEBRUIKSAANWIJZING
TELECAMERA PER RETROMARCIA UNIVERSALE
ISTRUZIONI PER L’USO
CÁMARA DE VISTA TRASERA UNIVERSAL
MANUAL DE INSTRUCCIONES
CÂMARA TRASEIRA UNIVERSAL
MANUAL DE INSTRUÇÕES
通用后视摄像头
使用说明书
B5A-0543-00 (W)
© 2014 JVC KENWOOD Corporation
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the best performance
from your new Universal Camera.
For your records
Record the serial number, found on the back of the unit, in the spaces designated on the warranty card,
and in the space provided below. Refer to the model and serial numbers whenever you call upon your
Kenwood dealer for information or service on the product.
Model CMOS-230 Serial number
US Residence Only
Register Online
Register your Kenwood product at www.Kenwoodusa.com
CMOS-230.indb 1CMOS-230.indb 1 14/11/07 13:1714/11/07 13:17
2 |
ENGLISH
• Before nally installing the unit, connect the wiring
temporarily, making sure it is all connected up properly,
and the unit and the system work.
• When mounting this unit, make sure none of the leads are
trapped between this unit and the surrounding metalwork
or ttings.
• Do not mount this unit near the heater outlet, where
it would be a ected by heat, or near the doors, where
rainwater might splash onto it. (Never install in locations
such as the above because of the danger of malfunction
due to high temperatures.)
• Before drilling any mounting holes always check behind
where you want to drill the holes. Do not drill into the gas
line, brake line, electrical wiring or other important parts.
• If this unit is installed in the passenger compartment,
anchor it securely so it does not break free while the car is
moving, and cause injury or an accident.
• If this unit is installed under a front seat, make sure it does
not obstruct seat movement. Route all leads and cords
carefully around the sliding mechanism so they do not get
caught or pinched in the mechanism and cause a short
circuit.
Care and maintenance
• When the product gets dirty, wipe dry with a silicon cloth
or soft cloth. If it is seriously stained, remove stain with
a cloth moistened with a neutral cleaner and then wipe
the cleaner away. Do not use a hard cloth and/or a volatile
substance such as lacquer thinner or alcohol, scratches,
deformation, degradation and/or damage may result.
• When a lens component gets dirty, wipe gently with a soft
cloth moistened with water. Do not rub with a dry cloth to
prevent scratching the lens.
Installation Procedure
1 To prevent a short circuit, remove the key from the
ignition and disconnect the - battery.
2 Make the proper input and output wire connections
for each unit.
3 Connect the wiring harness wires in the following
order: ground, ignition and camera unit.
4 Install the unit in your car.
5 Reconnect the - battery.
WARNING
To prevent injury or fire, take the following
precautions:
• To prevent a short circuit, never put or leave any metallic
objects (such as coins or metal tools) inside the unit.
• Installation and wiring of this product require specialist
skill and experience. To assure your safety, please request a
specialist technician to install the unit.
• When you make a hole to install the camera, check the
location of pipes, tanks and wiring and avoid touching
them. Otherwise it may cause the re.
• When you make a hole with a drill, use goggles to protect
your eyes.
CAUTION
To prevent damage to the product, take the
following precautions:
• Make sure to ground the unit to a negative 12V DC power
supply.
• When replacing a fuse, only use a new fuse with the
prescribed rating. Using a fuse with the wrong rating may
cause your unit to malfunction.
• Do not use your own screws. Use only the screws provided.
If you use the wrong screws, you could damage the unit.
NOTE
• A rear view camera is a camera that provides symmetrical
images in the same way as rear and side view mirrors.
• Connection to a TV with an RCA video input is possible,
but con rm whether the TV you use has a reverse gear
connection function.
• This product is designed to supplement the driver’s rear
view, but the camera images do not show all dangers and
obstacles. Be sure to look behind you when reversing to
con rm the view.
• This product features a wide-angle lens, so the near view
is wide and the far view is narrow, which may create a
false sense of distance. Be sure to look behind you when
reversing to con rm the view.
• Do not wash your car with an automatic car wash or
high-pressure water as it may result in water entering the
camera or the camera falling o .
• Check camera bracket installation before driving.
Are the screws loose?
- Is the camera bracket rmly secured?
- If the rear view camera comes loose while you are driving
it may cause an accident.
Before Use/ Installation Procedure
CMOS-230.indb 2CMOS-230.indb 2 14/11/07 13:1714/11/07 13:17
ENGLISH
| 3
• Lay the cords by avoiding high-temperature areas. Use
corrugated tubes for wiring inside the engine room. If a
cord contacts a high-temperature area of the vehicle, the
coating may melt and cause short-circuiting, which may
lead to a re or electric shock hazard.
Accessories
WARNING
• If you connect the ignition wire (Red) to the car chassis
(Ground), you may cause a short circuit, that in turn may
start a re. Always connect those wires to the power source
running through the fuse box.
• Do not cut out the fuse from the ignition wire (Red). The
power supply must be connected to the wires via the fuse.
CAUTION
• If your car’s ignition does not have an ACC position, connect
the ignition wires to a power source that can be turned on
and o with the ignition key. If you connect the ignition
wire to a power source with a constant voltage supply, as
with battery wires, the battery may die.
• If the fuse blows, rst make sure the wires aren’t touching
to cause a short circuit, then replace the old fuse with one
with the same rating.
• Insulate unconnected wires with vinyl tape or other similar
material. To prevent a short circuit, do not remove the caps
on the ends of the unconnected wires or the terminals.
• After the unit is installed, check whether the brake lamps,
blinkers, wipers, etc. on the car are working properly.
• Install so that it does not obstruct the rear eld of view.
• Install so that it does not protrude from the side of the car.
• Do not perform installation in rain or fog.
• When humidity is high, dry the surface to which the unit is
to be attached before installing.
• Moisture on the attachment surface reduces adhesive
strength, which may lead to the unit coming o .
• Do not attach the camera bracket to areas on the car body
treated with uorocarbon resin, or glass.
• May result in the rear view camera falling o .
- Do not apply water to the unit.
- Do not expose the unit to rain.
- Do not subject the camera to unnecessary force.
- Thoroughly clean where tape is used for sticking on the
unit.
• Refer to the Instruction’s manual for details on connecting
the other units, then make connections correctly.
• Secure the wiring with cable clamps or adhesive tape.
To protect the wiring, wrap adhesive tape around them
where they lie against metal parts.
• Route and secure all wiring so it cannot touch any moving
parts, such as the gear shift, handbrake and seat rails.
• Do not route wiring in places that get hot, such as near the
heater outlet. If the insulation of the wiring melts or gets
torn, there is a danger of the wiring short-circuiting to the
vehicle body.
• When replacing the fuse, be sure to use only fuse of the
rating prescribed on the fuse holder.
• To minimize noise locate the TV antenna cable, radio
antenna cable and RCA cable as far away from each other
as possible.
Grommet..........1
Camera bracket clamping screw..........1
Camera [with camera bracket (A)] ..........1
Power cord ..........1
Camera bracket (B) ..........1
CMOS-230.indb 3CMOS-230.indb 3 14/11/07 13:1714/11/07 13:17
Especificaciones del producto
| Marca: | Kenwood |
| Categoría: | cámara de coche |
| Modelo: | CMOS-230 |
¿Necesitas ayuda?
Si necesitas ayuda con Kenwood CMOS-230 haz una pregunta a continuación y otros usuarios te responderán
cámara de coche Kenwood Manuales
11 Julio 2024
11 Julio 2024
11 Julio 2024
11 Julio 2024
cámara de coche Manuales
- cámara de coche AEG
- cámara de coche Garmin
- cámara de coche Prestigio
- cámara de coche Abeo
- cámara de coche Sencor
- cámara de coche Overmax
- cámara de coche Ednet
- cámara de coche Rollei
- cámara de coche Navitel
- cámara de coche Targa
- cámara de coche Orion
- cámara de coche Dnt
- cámara de coche Zenec
- cámara de coche Mappy
- cámara de coche Vico
- cámara de coche BlackVue
- cámara de coche Roav
- cámara de coche Schou
- cámara de coche Rawlink
- cámara de coche EAL
- cámara de coche Roadhawk
- cámara de coche Top Dawg
Últimos cámara de coche Manuales
19 Octubre 2024
16 Septiembre 2024
16 Septiembre 2024
9 Septiembre 2024
9 Septiembre 2024
9 Septiembre 2024
7 Septiembre 2024
7 Septiembre 2024
7 Septiembre 2024
7 Septiembre 2024