Kenwood CMOS-320 Manual de Usario

Lee a continuación 📖 el manual en español para Kenwood CMOS-320 (60 páginas) en la categoría cámara de coche. Esta guía fue útil para 12 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/60
CMOS-320
CMOS-220
UNIVERSAL MULTI-VIEW CAMERA/ UNIVERSAL REAR VIEW CAMERA
INSTRUCTION MANUAL
CAMÉRA MULTI-VUES UNIVERSELLE/ CAMÉRA DE RECUL UNIVERSELLE
MODE D’EMPLOI
UNIVERSAL MULTIVIEW-KAMERA/ UNIVERSAL RÜCKFAHRKAMERA
BEDIENUNGSANLEITUNG
UNIVERSELE MULTIVIEWCAMERA/ UNIVERSELE ACHTERUITRIJCAMERA
GEBRUIKSAANWIJZING
LYT2720-001A (W)
© 2014 JVC KENWOOD Corporation
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the best performance
from your new Universal Camera.
For your records
Record the serial number, found on the back of the unit, in the spaces designated on the warranty card,
and in the space provided below. Refer to the model and serial numbers whenever you call upon your
Kenwood dealer for information or service on the product.
Model CMOS-320/CMOS-220 Serial number
US Residence Only
Register Online
Register your Kenwood product at ww w.Kenwoodusa.com
2 | CMOS-320/CMOS-220
• Beforenally installing the unit, connect the wiring
temporarily, making sure it is all connected up properly,
and and the unit the system work.
• When mounting unit, none the this make sure of leads are
trapped between this unit and the surrounding metalwork
orttings.
• Do not mount this unit near the heater outlet, where
it be would aected by heat, or near the doors, where
rainwater might splash onto it. (Never install in locations
such danger as the above because of the of malfunction
due high to temperatures.)
• Beforedrilling any mounting holes always check behind
where the the  you want to drill    holes. Do not drill into gas
line, line, wiring other important brake electrical or parts.
• If this unit is installed in the passenger compartment,
anchor it securely so itdoes not break free while the car is
moving, and cause injury or an accident.
• If a this unit is installed under front seat, make sure it does
not obstruct seat movement. Route all leads and cords
carefully the sliding around mechanism so they do not get
caught or pinched in a the mechanism and cause short
circuit.
Care and maintenance
• When the a product gets dirty, wipe dry with silicon cloth
or soft cloth. If it is seriously stained, remove stain with
a acloth moistened with neutral cleaner and then wipe
the a a cleaner away. Do not use hard cloth and/or volatile
substance such lacquer as thinner or alcohol, scratches,
deformation, damage degradation and/or may result.
• When component gentlya lens gets dirty, wipe witha soft
cloth moistened with water. Do not rub a with dry cloth to
preventscratchingthelens.
Installation Procedure
1 Topreventashortcircuit,removethe fromthekey
ignitionanddisconnectthe battery.-
2 Maketheproperinputandoutputwireconnections
foreachunit.
3 Connectthewiringharnesswiresinthefollowing
order:ground,ignitionandcameraunit.
4 Installtheunitinyourcar.
5 Reconnectthe battery.-
WARNING
To prevent injury or fire, take the following
precautions:
• To a prevent short circuit, never put or leave any metallic
objects (such as coins or metal tools) inside theunit.
• Installation and specialist wiring of this product require
skill and experience. To assure your safety, aplease request
specialist technician to install the unit.
• When the the a you make hole to install camera, check
location tanks and and of pipes, wiring avoid touching
them. Otherwise the it may cause re.
• When a a you make hole with drill, use goggles to protect
youreyes.
CAUTION
To prevent damage to the product, take the
following precautions:
• Make sure to ground the unit toa negative 12V DC power
supply.
• When replacing new the a afuse, only use fuse with
prescribed rating. Using the wronga fuse with rating may
cause to your unit malfunction.
• Do not use your own screws. Use only the screws provided.
If use you the wrong screws, you could damage the unit.
NOTE
• A a rear view camera is camera that provides symmetrical
images in the same way as rear and side view mirrors.
• Connection ato TVwith an RCA video input is possible,
but conrm whether the TV you use a has reverse gear
connection function.
• This product is designed to supplement the driver’s rear
view, but the camera images do not show all dangers and
obstacles. sure look Be  to behind  you when reversing to
conrm the view.
• This product a features wide-angle lens, so the near view
is far wide and the view ais narrow, which may create
false sense of distance. Be sure to look behind you when
reversing the view. to conrm
• Do not wash your car with an automatic car wash or
high-pressure water as it may result in water entering the
camera camera or the falling o.
• Check camera bracket installation before driving.
Are the screws loose?
- Is the camera bracket rmly secured?
- If the rear view camera comes loose while you are driving
it may cause an accident.
Before Use/ Installation Procedure
CMOS-320/CMOS-220 | 3
ENGLISH
• Lay the cords by avoiding high-temperature areas. Use
corrugated tubes for wiring inside the engine room. Ifa
cord contacts a high-temperature area of the vehicle, the
coating melt short-circuiting, may and cause which may
lead a to re or electric shockhazard.
Accessories
WARNING
• If you connect the ignition wire (Red) to the car chassis
(Ground),   a    you may cause short circuit, that in turn may
starta re. Always connect those wires to the power source
running the through fuse box.
• Do not cut out the fuse from the ignition wire (Red). The
power supply must be connected to the wires via the fuse.
CAUTION
• If your car’signition does not have an ACC position, connect
the ignition wires turned a to power source that can be on
and o with the ignition key. If you connect the ignition
wire voltage a a to power source with constant supply, as
with battery wires, the battery may die.
• If the fuse blows, rst make sure the wires aren’t touching
to cause short a circuit, then replace the old fuse with one
with the same rating.
• Insulate unconnected wires with vinyl tape or other similar
material. a To prevent short circuit, do not remove the caps
on ends the of the unconnected wires or the terminals.
• After the unit is installed, check whether the brake lamps,
blinkers, wipers, etc. on the car are working properly.
• Install so that it does not obstruct the rear eld of view.
• Install so that it does not protrude from the side of thecar.
• Do not perform installation in rain or fog.
• When humidity the the   is high, dry surface to which  unit is
to be attached before installing.
• Moisture on the attachment surface reduces adhesive
strength, the coming which may lead to unit o.
• Do not attach the camera bracket to areas on the car body
treated with uorocarbon resin, or glass.
• May result in the rear view camera falling o.
- Do not apply water to the unit.
- Do not expose the unit to rain.
- Do not subject the camera to unnecessary force.
- Thoroughly for clean where tape is used sticking on the
unit.
• Refer to the Instruction’s manual for details on connecting
the other then connections units, make correctly.
• Secure the wiring with cable clamps or adhesive tape.
To protect the wiring, wrap adhesive tape around them
where they lie against metal parts.
• Route and secure all wiring so it cannot touch any moving
parts, such as the gear shift, handbrake and seat rails.
• Do not route wiring in places that get hot, such as near the
heater outlet. If the insulation of the wiring melts or gets
torn, a there is danger of   the wiring short-circuiting to the
vehiclebody.
• When replacing the fuse, be sure to use only fuse of the
rating the holder. prescribed on fuse
• To minimize noise locate the TV antenna cable, radio
antenna cable and cable each RCA as far away from other
aspossible.
Grommet..........1
Camerabracketclampingscrew..........1
Camera(withcamerabracket)..........1
Switchunit..........1
Double-sideadhesivetape..........1
CMOS-320 only
Power ..........1cord
CMOS-320  CMOS-220

Especificaciones del producto

Marca: Kenwood
Categoría: cámara de coche
Modelo: CMOS-320

¿Necesitas ayuda?

Si necesitas ayuda con Kenwood CMOS-320 haz una pregunta a continuación y otros usuarios te responderán




cámara de coche Kenwood Manuales

cámara de coche Manuales

Últimos cámara de coche Manuales