Kern HMO Manual de Usario
Kern
Meetapparatuur
HMO
Lee a continuación 📖 el manual en español para Kern HMO (17 páginas) en la categoría Meetapparatuur. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/17
Sauter GmbH
Ziegelei 1
D-72336 Balingen
e-mail: info@kern-sohn.com
Phone : +49-[0]7433- 9933-0
Fax: +49-[0]7433- - 9933 149
Internet: www.sauter.eu
Instruction manual mobile Leeb
hardness tester
SAUTER HMO
Version 2.0
04/2020
GB
HMO- -e- BA 2020
PROFESSIONAL MEASURING
2 HMO- -e- BA 2020
GB
SAUTER HMO
V. 2.0 04/2020
Instruction manual mobile Leeb hardness tester
Thank you for purchasing the mobile digital Leeb impact hardness tester from
SAUTER. We hope that you will be very satised with the high quality of this device
and its extensive functionality. For any questions, wishes and suggestions we are at
your disposal.
Table of contents:
1 Before commissioning .................................................................................. 3
2 Introduction .................................................................................................... 3
2.1 Measuring principle .................................................................................................................. 3
2.2 Structure .................................................................................................................................... 4
2.3 Technical data ........................................................................................................................... 5
2.4 Area of application ................................................................................................................... 5
3 Test procedure ............................................................................................... 6
3.1 Preparation of the device 6........................................................................................................
3.2 Preparation of the sample ....................................................................................................... 6
3.3 Test execution .......................................................................................................................... 8
3.4 Browsing ................................................................................................................................... 8
3.5 Print 9............................................................................................................................................
4 Setup ............................................................................................................... 9
4.1 Settings in the main mask ....................................................................................................... 9
4.2 Menu settings ......................................................................................................................... 10
5 Care and maintenance ................................................................................. 14
5.1 Periodic maintenance ............................................................................................................ 14
5.2 Store ......................................................................................................................................... 14
5.3 Calibration ............................................................................................................................... 15
6 Annex ............................................................................................................ 16
6.1 Conversion area ..................................................................................................................... 17
6.2 Scope of delivery .................................................................................................................... 17
HMO- -e- 3 BA 2020
1 Before commissioning
Before putting the device into operation, check the delivery for any transport damage
to the packaging, the plastic case and the device itself. Should this be the case,
SAUTER must be contacted immediately.
2 Introduction
2.1 Measuring principle
The measuring principle for the measurements carried out with this dynamic impact
hardness tester is physically quite uncomplicated. An impact body with a hard metal
tip is hurled against the surface of the test object by the spring force. When the impact
body hits the surface, it can be damaged, which ultimately leads to a loss of kinetic
energy.
This energy loss is calculated on the basis of velocity measurements, at a certain point
in time when the impactor is at a certain distance from the surface, both in the rebound
and impact phases.
The xed magnet in the impact body generates an induction voltage in the simple wire
coil of the impact tester. The voltage of the signal is proportional to the speed of the
impact body. The signal is processed by the electronics so that the hardness value can
be read on the display and then stored.
English
German
Impact phase
Impact phase
Rebound phase
Rebound phase
Time
Time
Especificaciones del producto
Marca: | Kern |
Categoría: | Meetapparatuur |
Modelo: | HMO |
¿Necesitas ayuda?
Si necesitas ayuda con Kern HMO haz una pregunta a continuación y otros usuarios te responderán
Meetapparatuur Kern Manuales
19 Septiembre 2024
19 Septiembre 2024
19 Septiembre 2024
19 Septiembre 2024
19 Septiembre 2024
19 Septiembre 2024
19 Septiembre 2024
19 Septiembre 2024
19 Septiembre 2024
19 Septiembre 2024
Meetapparatuur Manuales
- Meetapparatuur Bosch
- Meetapparatuur Honeywell
- Meetapparatuur Pioneer
- Meetapparatuur Amprobe
- Meetapparatuur Silverline
- Meetapparatuur Gude
- Meetapparatuur Black And Decker
- Meetapparatuur Beurer
- Meetapparatuur Extech
- Meetapparatuur ABB
- Meetapparatuur Hazet
- Meetapparatuur Metrix
- Meetapparatuur Benning
- Meetapparatuur Voltcraft
- Meetapparatuur Mitsubishi
- Meetapparatuur Velleman
- Meetapparatuur Vemer
- Meetapparatuur Perel
- Meetapparatuur Kyoritsu
- Meetapparatuur Ideal
- Meetapparatuur Flir
- Meetapparatuur Grohe
- Meetapparatuur Continental Edison
- Meetapparatuur Testboy
- Meetapparatuur Goclever
- Meetapparatuur Danfoss
- Meetapparatuur Hager
- Meetapparatuur Bresser
- Meetapparatuur TFA
- Meetapparatuur Powerfix
- Meetapparatuur Finder
- Meetapparatuur Fluke
- Meetapparatuur Fantini Cosmi
- Meetapparatuur Eltako
- Meetapparatuur Sekonic
- Meetapparatuur Laserliner
- Meetapparatuur REV
- Meetapparatuur Testo
- Meetapparatuur Eastron
- Meetapparatuur ORNO
- Meetapparatuur RIDGID
- Meetapparatuur Multimetrix
- Meetapparatuur GW Instek
- Meetapparatuur Greisinger
- Meetapparatuur Beha-Amprobe
- Meetapparatuur Kogan
- Meetapparatuur Kemo
- Meetapparatuur Peak
- Meetapparatuur Uni-T
- Meetapparatuur Elgato
- Meetapparatuur Hikmicro
- Meetapparatuur PeakTech
- Meetapparatuur Sonel
- Meetapparatuur Tru Components
- Meetapparatuur Emko
- Meetapparatuur Entes
- Meetapparatuur Trumeter
- Meetapparatuur Atmel
- Meetapparatuur Qualita
- Meetapparatuur MGL Avionics
- Meetapparatuur Adwa
- Meetapparatuur Chauvin Arnoux
- Meetapparatuur Megger
- Meetapparatuur Gossen Metrawatt
- Meetapparatuur PCE Instruments
- Meetapparatuur CEM
- Meetapparatuur Hameg
- Meetapparatuur TDE Instruments
- Meetapparatuur Joy-it
- Meetapparatuur Circutor
- Meetapparatuur Klein Tools
- Meetapparatuur Aerospace Logic
- Meetapparatuur Janitza
- Meetapparatuur Sanwa
- Meetapparatuur Qubino
- Meetapparatuur Camille Bauer
- Meetapparatuur Seaward
- Meetapparatuur LabNation
- Meetapparatuur Electronics International
- Meetapparatuur AkYtec
- Meetapparatuur Stahlwille
- Meetapparatuur MASIMO
- Meetapparatuur Enda
Últimos Meetapparatuur Manuales
19 Septiembre 2024
19 Septiembre 2024
19 Septiembre 2024
19 Septiembre 2024
18 Septiembre 2024
18 Septiembre 2024
18 Septiembre 2024
18 Septiembre 2024
18 Septiembre 2024
18 Septiembre 2024