Satel Graphite Manual de Usario

Satel detector de movimiento Graphite

Lee a continuación 📖 el manual en español para Satel Graphite (4 páginas) en la categoría detector de movimiento. Esta guía fue útil para 5 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/4
®
GRAPHITE
DIGITAL PASSIVE INFRARED DETECTOR
graphite_en 01/15
The GRAPHITE detector allows detection of motion in the protected area. This manual applies to the detector
with electronics version H (or newer).
1. Features
Dual element pyrosensor.
Digital motion detection algorithm.
Digital temperature compensation.
Adjustable detection sensitivity.
Built-in EOL resistors.
LED to indicate alarm status.
Remote LED enable/disable.
Alarm memory.
Supervision of detector signal path and supply voltage.
Tamper protection against cover removal.
2. Specifications
Supply voltage ...................................................................................................................................12 V DC ±15%
Standby current consumption......................................................................................................................... 12 mA
Maximum current consumption ...................................................................................................................... 14 mA
EOL resistors ............................................................................................................................................ 2 x 1.1 k
Relay contacts rati .....40 mA / 16 V DC ng (resistive load).........................................................................................
Detectable speed......................................................................................................................................0.3...3 m/s
Alarm signaling period .......................................................................................................................................... 2 s
Warm-up period.................................................................................................................................................. 30 s
Recommended installation height ....................................................................................................................2.4 m
Security grade according to EN50131-2-2 ...................................................................................................Grade 2
Standards complied with ........................................................ EN50131-1, EN50131-2-2, EN50130-4, EN50130-5
Environmental class according to EN50130-5 ........................................................................................................II
Operating temperature range ................................................................................................................ -30...+55 °C
Maximum humidity..........................................................................................................................................93±3%
Dimensions ..................................................................................................................................... 63 x 96 x 49 mm
Weight.................................................................................................................................................................94 g
3. Description
After motion is sensed by the detector y contacts will open for 2 seconds. in the coverage area, the alarm rela
Supervision features
In the event of the voltage drop below 9 V (± 5%) for more than 2 seconds or the signal path failure, the detector
will signal a trouble. The trouble is indicated by the activation of alarm relay and the steady light of LED
indicator. The trouble signaling will continue as long as the trouble persists.
Remote LED enable/disable
The LED can be enabled/disabled remotely, if the LED has not been enabled using the LED ON/OFF pins. The
LED terminal is provided to allow remote LED enable/disable. The LED is enabled, when the terminal is
connected to the common ground, and disabled, when the terminal is disconnected from the common ground.
2 GRAPHITE SATEL
You can connect to the LED terminal an OC type control panel output programmed e.g. as the SERVICE MODE
STATUS, . BI SWITCH or ZONE TEST STATUS
Alarm memory
If the LED is enabled, the detector can indicate the alarm memory. The MEM terminal is provided to allow the
alarm memory feature enable/disable. The feature is enabled, when the terminal is connected to the common
ground. The feature is disabled, when the terminal is disconnected from the common ground. If the alarm
memory feature is enabled and an alarm occurs, the LED will start blinking. Indication of the alarm memory will
continue until the alarm memory feature is enabled again (the MEM terminal is connected to the common
ground). Disabling the alarm memory feature will not stop the alarm memory indication. You can connect to the
MEM terminal an OC type control panel output programmed e.g. as the ARMED STATUS.
4. Electronics board
terminals:
NC - alarm output (NC relay).
TMP - tamper output (NC).
COM - common ground.
12V - power input.
LED - remote LED control.
MEM - alarm memory control.
configuration pins for detector outputs:
the built-in resistors are to be used – place the jumpers as shown in Fig. 2 (connect the outputs as shown
in Fig. 10),
the built-in resistors are not to be used – place the jumpers as shown in Fig. 3 (connect the outputs as
shown in Fig. 9).
tamper switch.
scale for positioning of pyroelectric sensor against the lens (see: Fig. 8).
fixing screw hole.
red color LED to indicate:
alarm – ON for 2 seconds,
alarm memory – blinking rapidly,
trouble – ON,
warm-up – blinking slowly.
LED enable/disable pins. The LED is enabled, if the jumper is placed over the pins (the pins are shorted).
dual element pyrosensor. Do not touch the pyroelectric sensor, so as not to soil it.
potentiometer for sensitivity adjustment.
SATEL GRAPHITE 3
5. Installation
Disconnect power before making any electrical connections.
1. Remove the front cover (Fig. 4).
2. Remove the electronics board.
3. Make the openings for screws and cable in the enclosure base.

Especificaciones del producto

Marca: Satel
Categoría: detector de movimiento
Modelo: Graphite

¿Necesitas ayuda?

Si necesitas ayuda con Satel Graphite haz una pregunta a continuación y otros usuarios te responderán


detector de movimiento Satel Manuales

Satel

Satel SLIM-PIR-LUNA Manual de Usario

17 Septiembre 2024
Satel

Satel APMD-250 Manual de Usario

3 Septiembre 2024
Satel

Satel SLIM-DUAL-PRO Manual de Usario

1 Septiembre 2024
Satel

Satel APD-200 Manual de Usario

1 Septiembre 2024
Satel

Satel AOD-210 Manual de Usario

1 Septiembre 2024
Satel

Satel OPAL Pro Manual de Usario

31 Agosto 2024
Satel

Satel Graphite Manual de Usario

31 Agosto 2024
Satel

Satel AOCD-250 Manual de Usario

30 Agosto 2024
Satel

Satel GREY Plus Manual de Usario

29 Agosto 2024
Satel

Satel SLIM-PIR-PRO Manual de Usario

29 Agosto 2024

detector de movimiento Manuales

Últimos detector de movimiento Manuales

Maxsa

Maxsa 40234 Manual de Usario

19 Septiembre 2024
Maxsa

Maxsa 43218 Manual de Usario

19 Septiembre 2024
ORNO

ORNO OR-CR-233 Manual de Usario

19 Septiembre 2024
ORNO

ORNO OR-CR-219 Manual de Usario

19 Septiembre 2024
ORNO

ORNO OR-CR-232 Manual de Usario

19 Septiembre 2024
ORNO

ORNO OR-CR-231 Manual de Usario

19 Septiembre 2024
Jung

Jung BTLC17181244 Manual de Usario

18 Septiembre 2024
Jung

Jung BTLC17182250 Manual de Usario

18 Septiembre 2024
Jung

Jung BTLC17181255 Manual de Usario

18 Septiembre 2024
Jung

Jung BTLC17182259 Manual de Usario

18 Septiembre 2024