SSV Works RG4-F65K Manual de Usario

SSV Works Vocero RG4-F65K

Lee a continuación 📖 el manual en español para SSV Works RG4-F65K (3 páginas) en la categoría Vocero. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/3
RG4-F65
Polaris Ranger
6.5” Speaker Front Kick Panels
SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030
www.SSVworks.com | Phone: 818-991-1778 | Fax: 866-293-6751
!
Please read and understand these
instructions completely before
installation to avoid possible injury, or
damage to the accessory or vehicle.
WARRANTY INFORMATION:
All SSV Works enclosures are covered by a limited lifetime warranty against defects in material
or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against
defects in material or workmanship. All SSV Works Speakers are covered by a limited 1 year
warranty against defects in material or workmanship. Labor for replacement of defective
components is not covered. Contact SSV Works for further warranty information.
TOOLS NEEDED FOR INSTALLATION
PARTS LIST IMAGES
2. Enclosure Brackets x 41. RG4-F65 Enclosures
(1 pair)
3. M6 x 16mm Screws
x 10
- T-30 Torx Driver - Panel Removal Tool
4. M6 Washers x 8 (small) 4. M6 Washers x 2 (large)
A. Remove hood by turning locking pins and lifting up.
A
B. Use a panel tool to extract push pins circled in pink.
B
C. With push pins extracted, lift to remove the cup holder and gauge cluster.
C
- Phillips Screwdriver
K. Using the supplied M6 screws and small washers, install the
brackets to kick pods.
L. Remove factory T40 torx screws located from the front of the
dash next to the cup holders.
K L
F. Extract push pins that are now exposed from removing the
upper glove box.
H. Extract push pins exposed from gauge cluster removal.
I. Extract push pins located above driver and passenger side cup
holders.
F
H
I
E. Unscrew (4) torx screws located in upper glove box and
remove box.
G. Extract push pins exposed from cup holder removal.
E
G
J. Lift to remove the dash.
J
Connecting the RG4-F65 using the
pre-installed, two-pin connector will
require an optional SSV Works plug-
&-play harness (WP-H1149 - sold
separately). If you are not using the
WP-H1149 harness, simply cut off
the two-pin connector and follow the
wiring instruction.
Repeat for the other side.
RG4-F65 © 2018 SSV Works, Oxnard, CA 93030 RG4-F65 Rev. B 7-23-18
WIRING INSTRUCTIONS
For proper sound, ensure the speaker
polarity is correct connect the+to
the “+” and the “-“to the-“from the
speaker wire to the amplier. If using
with an SSV Works complete system
refer to the amplier wiring instructions
for more detailed wiring information.
“+”
“+”
-
-
M. Remove factory T25 torx screws located underneath the dash. N. Located on the inside top of the pocket you will have two
holes, route speaker wire though the larger hole. The smaller
hole will be used to mount the pod in Step P.
O. Place the speaker pod in location and resecure the factory screws through the pod brackets on the front and underneath the dash.
P. From the inside-top of the dash, secure the top mounting M6 screw and large washer to the pod through the smaller hole next to
the routed speaker wire.
M N
O
P P
O

Especificaciones del producto

Marca: SSV Works
Categoría: Vocero
Modelo: RG4-F65K

¿Necesitas ayuda?

Si necesitas ayuda con SSV Works RG4-F65K haz una pregunta a continuación y otros usuarios te responderán




Vocero SSV Works Manuales

Vocero Manuales

Últimos Vocero Manuales