SSV Works X3-US10 Manual de Usario

SSV Works Vocero X3-US10

Lee a continuación 📖 el manual en español para SSV Works X3-US10 (5 páginas) en la categoría Vocero. Esta guía fue útil para 4 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/5
X3-US10
2016+ Can-Am Maverick x3
10” Under Seat Enclosure
SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030
www.SSVworks.com | Phone: 818-991-1778 | Fax: 866-293-6751
!
Please read and understand these
instructions completely before
installation to avoid possible injury, or
damage to the accessory or vehicle.
WARRANTY INFORMATION:
All SSV Works enclosures are covered by a limited lifetime warranty against defects
in material or workmanship. All SSV Works Electronics are covered by a limited 1 year
warranty against defects in material or workmanship. All SSV Works Speakers are
covered by a limited 1 year warranty against defects in material or workmanship. Labor
for replacement of defective components is not covered. Contact SSV Works for further
warranty information.
1. X3-US10 Enclosure
2. M6 x 16mm Screws x 10
3. M6 Washers x 10
4. M6 x 25mm Screw x 1
TOOLS NEEDED FOR INSTALLATION PARTS LIST
PARTS LIST IMAGES
5. Large washers x 2
6. D-Brackets x 2
7. A-Bracket x 1
8. B-Bracket x 1
2. M6 x 16mm Screws x 10
7. A-Bracket x 1
11. M6 Locking Hex Nut
8. B-Bracket x 1
12. Foam Strips x 3
3. M6 Washers x 10 4. M6 x 25mm Screw x 1
5. Large washers x 2
9. Seat Risers x 2
1. X3-US10 Enclosure
6. D-Brackets x 2
10. Small Spacer x 1
- 10mm Socket or Wrench
- T-30 Torx Driver
- T-40 Torx Driver
9. Seat Risers x 2
10. Small Spacer x 1
11. M6 Locking Hex Nut
12. Foam Strips x 3
A. Apply the foam strips to the inside right, left and top side of
the enclosure.
C. Remove the factory 10mm nut and bolt from the brake line. Place the washer on top of the factory bracket and push the long M6x25mm screw through
the top. Then attach the brake line, spacer, washer and nut. T hen hand tighten.
B. Using the supplied M6 screws and washers, screw the DD-brackets
to the bottom right and left side of the enclosure.
X3-US10
AB
C C C
SSV HOLE PATTERN
KICKER HOLE PATTERN
FOR UNLOADED ENCLOSURES:
Pink hole pattern: SSV Works Subwoofer
Blue hole pattern: Kicker Subwoofer
If using a different brand subwoofer,
rst see if the subwoofer holes line up
with either one of the pre-drilled hole
patterns. If not, make sure to drill new
holes away from the pre-drilled holes.
Be sure to use the 8 supplied SSV Works
#7 screws when installing your own
subwoofer. #7 Screws x 8
F. Place B-Bracket to the left side of the enclosure and slide the tab underneath the enclosure. (F1) Line up the 2 screw holes and proceed to hand thread
the M6 screws and washers. Use a T30 Torx bit to tighten screws. Repeat for the right side. (F2) Line up the top of bracket A and B with the holes on
the factory seat brakcet. Screw in the M6 screw with the large washer (F3).
G. Route the speaker wire away from any moving parts and any sharp
metal, then connect to the amplier.
Connecting the X3-US10 using the pre-installed, four-pin
connector will require an optional SSV Works plug-&-play
harness B-H1152 - sold separately).
D. Replace the factory seat bolt spacers with the supplied SSV
Works spacers
E. Run the brake line along the dedicated channel on the sub enclosure while feeding
the enclosure down under the seat bar (F1). Make any adjustments to the brake
line so the enclosure lays on top of it. Line up the rear enclosure brackets to the
rear seat bolts and press down until the brackets rest on top of the spacers.
X3-US10
G
F1 F2 F3
DE1 E2

Especificaciones del producto

Marca: SSV Works
Categoría: Vocero
Modelo: X3-US10

¿Necesitas ayuda?

Si necesitas ayuda con SSV Works X3-US10 haz una pregunta a continuación y otros usuarios te responderán




Vocero SSV Works Manuales

Vocero Manuales

Últimos Vocero Manuales