Sussex BLMDSRH Manual de Usario
Lee a continuación 📖 el manual en español para Sussex BLMDSRH (2 páginas) en la categoría Grúa. Esta guía fue útil para 8 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/2
Product code
Suba
BLMDSRH Lever mixer diverter system
Lever mixer diverter system Dress kit
1
NOGGING
80 mm
Backplate
Finished
Wall Surface
Apply Silicone
Masterfit
Apply Silicone
Stud Face
Set
Screw
Handle
Body
2
NOGGING
80 mm
Backplate
Finished
Wall Surface
Set
Screw
Handle
Body
Apply Silicone
Masterfit
Apply Silicone
Stud Face
Diverter dress kit
Mixer dress kit
- Remove Mixer protective cover.
- Using silicon, seal the wall surface around the Mixer.
- Apply a small amount of silicon to the rear of the backplate prior to mounting onto the wall.
- Fit the handle body onto the Mixer Cartridge Lever ensuring the Handle is fully engaged.
- Secure the Handle Body by tightening the Set screw using the Allen Key provided (tighten well).
- Remove Mixer protective cover.
- Using silicone, seal the wall surface around the Diverter.
- Apply a small amount of silicone to the rear of the backplate prior to mounting onto the wall.
- Fit the Handle Body onto the Diver ter Adapter, ensure the Handle is fully engaged.
- Secure the Handle Body by tightening the Set screw using the Allen Key provided (tighten well).
To complete the installation, operate the Mixer(s) checking the flow of both hot and cold water from Outlet.
Check all fittings and fixtures for water leaks.
sussextaps.com.au
Tapware is to be installed by a Licensed Plumber in accordance with AS/NZS 3500:2003
Recommended working water pressure 300-500 kpa. Maximum water temperature is 65 deg.c
Copyright © Sussex Taps.
Product code
Suba
BLMDSRH Lever mixer diverter system
Lever mixer diverter system Rough in
1
NOGGING
Dress Ring
Handle
Body
Wall Covering
Max. 30mm
90
Stud face
Pipe Connections
Maste trfi
Outlet
1
Mixer
Min.
8mm
This
Side
UP
Diverter
70
Vi ew f ro m ab ov e
No te: Th e di ve rt er i s of t he d ial ty pe , ro ta te h andl e to d irec t
Cold
Hot
Mixer
Outlet 1
Outlet 2
Diverter
30-32mm
Back Plate
Plumber note
Pipe connections
Rough in plumbing
- Prior to installing, calculate the finished wall thickness, maximum is 30mm thick, contact manufacturer for
further options.
- If Wall thickness is greater than 30mm, contact manufacturer for further options.
- Prepare a Nogging to be fixed parallel between the Wall Studs.
- The Nogging must be fitted to enable the base of the Masterfit to be 30-32mm back from the Stud Face.
- The Masterfit will be marked “This side Up” to indicate orientation.
- Using the screws (x4) provided, mount the Masterfit to the Nogging. Ensure the Masterfit is level and square.
- On-site high pressure line testing must be conducted with the Mixer in the closed position. (STATIC TEST ONLY)
- Under no circumstances is the Mixer to be opened when exceeding the maximum stated water pressure.
- At the completion of the testing, do not relieve any high pressure by opening the Mixer.
- Exposing the internals of the Mixer Cartridge to higher than specified water pressures, will void the
manufacturer’s warranty.
- The Hot and Cold ports are marked on the Masterfit. (Mixers have individual Hot/Cold inlet ports).
- Flush all water feed lines. All lines must be free from any dirt and debris before connecting to the Masterfit.
- Connect Hot and Cold lines to the corresponding 1/2” BSP ports of the Masterfit. (see Drawing)
- Do not remove any factory fitted pressure plugs or Fixings.
- Once all water connections are made, check Hot/Cold water flow by operating the Mixer Cartridge.
- Check all fittings and fixtures for leaks.
- Leave the Mixer(s) in the closed position and replace the Mixer protective cover.
- Store the Dress Kit in a safe place until required (see Dress Finishing Guide)
sussextaps.com.au
Tapware is to be installed by a Licensed Plumber in accordance with AS/NZS 3500:2003
Recommended working water pressure 300-500 kpa. Maximum water temperature is 65 deg.c
Copyright © Sussex Taps.
Especificaciones del producto
| Marca: | Sussex |
| Categoría: | Grúa |
| Modelo: | BLMDSRH |
¿Necesitas ayuda?
Si necesitas ayuda con Sussex BLMDSRH haz una pregunta a continuación y otros usuarios te responderán
Grúa Sussex Manuales
25 Septiembre 2024
25 Septiembre 2024
13 Septiembre 2024
13 Septiembre 2024
13 Septiembre 2024
13 Septiembre 2024
13 Septiembre 2024
12 Septiembre 2024
12 Septiembre 2024
12 Septiembre 2024
Grúa Manuales
- Grúa IKEA
- Grúa Etna
- Grúa Inventum
- Grúa Smeg
- Grúa KitchenAid
- Grúa Teka
- Grúa Miomare
- Grúa Ernesto
- Grúa CDA
- Grúa Stiebel Eltron
- Grúa Elba
- Grúa Grohe
- Grúa Franke
- Grúa Nodor
- Grúa Delta
- Grúa Schütte
- Grúa Elkay
- Grúa Caple
- Grúa Quooker
- Grúa Brita
- Grúa ZLine
- Grúa Hansgrohe
- Grúa Lynx
- Grúa Empire
- Grúa Moen
- Grúa Aloni
- Grúa WillieJan
- Grúa Sani-Lav
- Grúa Mizzo
- Grúa Brauer
- Grúa Fala
- Grúa Lomazoo
- Grúa Livarno Lux
- Grúa Billi
- Grúa Deante
- Grúa Omnires
- Grúa Zip
- Grúa Viidako
- Grúa Curaqua
- Grúa Waltec
- Grúa Fantini
- Grúa Oliveri
- Grúa Rogerseller
- Grúa Axor
- Grúa Gessi
- Grúa Graff
- Grúa Zurn
Últimos Grúa Manuales
6 Octubre 2024
2 Octubre 2024
1 Octubre 2024
1 Octubre 2024
1 Octubre 2024
1 Octubre 2024
1 Octubre 2024
1 Octubre 2024
1 Octubre 2024
1 Octubre 2024