Sussex RWBHS200RH Manual de Usario

Sussex Grúa RWBHS200RH

Lee a continuación 📖 el manual en español para Sussex RWBHS200RH (1 páginas) en la categoría Grúa. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/1
Tapware is to be installed by a Licensed Plumber in accordance with AS/NZS 3500:2003
Recommended working water pressure 300-500 kpa. Maximum water temperature is 65 deg.c
Copyright © Sussex Taps.
Pipe Connections
1/2" BSP
HOT
IN
OUTLET
1/2" BSP
COLD
IN
1A
NOGGING
WALL
STUD
28-32
Wall Covering
25mm
"ROUGH-IN" View from above
90
OUTLET
IN-WALL BODY
MASTERFIT
THIS
SIDE
UP AS/NZS 3718:2005
LIC. 20081
1
LOCKING
SLEEVE
HANDLE
DRESS
RING
5.5
Licence No. 0124
In ac cord anc e with AS/NZS 6400
Sussex Taps Pty Ltd
WATER RATING
www.waterr ating.g ov.au
The mo re
stars the mo re
water efcient
Product code
Circa
Wall basin hostess system
Fitting off
Pipe connections
Rough in plumbing (MASTERFIT) mounting guide
- The Masterfit will be supplied with the Spindles pre-installed.
- Prepare a nogging and secure 28-32mm back from the front Using the screws (x4) of the stud (See Fig.1)
- The Masterfit (in-wall) will be marked “This side Up” to Ensure the Masterfit is indicate orientation.
- Using the screws (x4) provided, mount the Masterfit (in-wall) to the Nogging.
- Ensure the Masterfit is level and square to the Wall Studs.
- Seal the wall around the Locking Sleeve and immediately fit the Dress Ring.
- Fit the Handle Body, the Handle Body must be fully engaged onto the Spindle; note the Set Screw contact point.
(See Fig.1B)
- Secure the Handle body by tightening the Set screw using the 2mm Allen key provided. (Tighten well)
- After completing the installation, establish water supply, check function of Tapware and ensure no water leaks.
- The Masterfit is supplied with coloured thread Caps to protect and identify the Hot and Cold inlet connections.
- All lines must be free from any dirt and debris before connecting to the Masterfit. Flush all water feed lines.
- Connect Hot and Cold lines to the corresponding 1/2” BSP ports of the Masterfit. (See Fig.1A)
- Do not remove or disturb any factory fitted Pressure Plugs or Fixings.
- Once all water connections are made, use the “Spindle Handle Adapter” and check Hot/Cold water operation.
- Check all fittings and connections for leaks.
- Store the Dress Kit in a safe place until required for Fit off.
RWBHS150RH Wall basin hostess syst 150mm
RWBHS200RH Wall basin hostess syst 200mm
RWBHS250RH Wall basin hostess syst 250mm
RWBHS150RH-V Wall basin hostess syst 150mm - Vertex
RWBHS200RH-V Wall basin hostess syst 200mm - Vertex
RWBHS250RH-V Wall basin hostess syst 250mm - Vertex
sussextaps.com.au

Especificaciones del producto

Marca: Sussex
Categoría: Grúa
Modelo: RWBHS200RH

¿Necesitas ayuda?

Si necesitas ayuda con Sussex RWBHS200RH haz una pregunta a continuación y otros usuarios te responderán




Grúa Sussex Manuales

Grúa Manuales

Últimos Grúa Manuales