Tecmate Optimate 6 Ampmatic Manual de Usario

Tecmate cargador de bateria Optimate 6 Ampmatic

Lee a continuación 📖 el manual en español para Tecmate Optimate 6 Ampmatic (34 páginas) en la categoría cargador de bateria. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/34

Automatic charger for 12V lead-acid batteries

Chargeur automatique pour batteries 12V plomb-acide

Cargador automático para baterías 12V plomoácido

Automatische Ladegerät für 12V Blei-Säure Batterien

Automatische lader voor 12V loodzuur accu’s

Caricabatterie automatico per batterie 12V piombo-acido

Automatisk diagnostisk laddare för 12V blybatterier

Automatick. nab.ječka pro 12V olovo/kyselinov. baterie

Автоматическое зарядное устройство для 12В

свинцово-кислотных аккумуляторных батарей

12V     

1 x 12V

STD / AGM-MF / GEL

3 - 240Ah (max. Ah rating

based on 48 hour charge).

+ -

MODEL: TM180 (EU), TM181 (US), TM182 (UK),

TM188 (AU), TM189 (KR)

AC: 100 – 240V 50-60Hz

0.85A @ 240V / 1.5A @ 100V

DC: 60W 12V 5A 

Thermally adjusted

INSTRUCTIONS FOR USE

IMPORTANT: Read completely

before charging

MODE D’EMPLOI

IMPORTANT: à lire avant

d’utiliser l’appareil

MODO DE EMPLEO

IMPORTANTE: a leer antes de

utilizar el aparato

ANWENDUNGSVORSCHRIFTEN

WICHTIG: Vollständig vor der

Benutzung lesen

GEBRUIKSAANWIJZING

BELANGRIJK: Lees volledig voor

gebruik

ISTRUZIONI PER L’USO

IMPORTANTE: da leggere prima

di utilizzare l’apparecchio

INSTRUKTIONER VIKTIGT: läs

följande fullständiga instruk-

tioner för användningen innan

du använder laddaren

INSTRUKCE PRO POUŽIT.

DŮLEŽIT: Přečtěte si pozorně

před použit.m

    

 :    

TM18x-IN1-170208

SAVE

sulphated

battery

OPTIMIZE

2 5

Pulse

SAVE

TEST after

CHARGE

3 6

Controlled

CHARGE

OptiMate

‘365’

maintenance

TEST before

charge

Low Volt

Start (0.5V)

Pulse

Wake up

ИНСТРУКЦИЯ ПО

ЭКСПЛУАТАЦИИ

ВАЖНО:

Прочти полностью перед

использованием

0.5V

13.6V

14.4V

2. TE

. 3.START P

5. 6. 7. 8. 9.SAVE CHARGE OPTIMIZE FINAL TEST MAINTAIN

24-7-365

2. TE

1. 3.START P

5. 6. 7. 8. 9.SAVE CHARGE OPTIMIZE FINAL TEST MAINTAIN

24-7-365

™

IMPORTANT SAFETY

INSTRUCTIONS FOR CANADA & USA

THIS PORTION OF THE MANUAL CONTAINS IMPORTANT SAFETY INSTRUCTIONS FOR

THE OPTIMATE 6 BATTERY CHARGER. IT IS OF THE UTMOST IMPORTANCE THAT

EACH TIME, BEFORE USING THE CHARGER, YOU READ AND EXACTLY FOLLOW THESE

INSTRUCTIONS. SAVE THESE INSTRUCTIONS.

Automatic charger for 12V lead-acid batteries

DO NOT USE FOR NiCd, NiMH, Li-Ion OR NON-RECHARGEABLE BATTERIES.

1. CAUTION : CLASS II APPLIANCE. DO NOT CONNECT TO GROUND.

2. Do not expose charger to rain or snow.

3. Use of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of fire, electric shock,

or injury to persons.

4. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when disconnecting charger.

5. An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result

in a risk of fire and electric shock. If extension cord must be used make sure that :

a) pins on plug of extension cord are the same number, size and shape as those of plug on charger.

b) the extension cord is properly wired and in good electrical condition, and

c) the conductor wire size is large enough for the AC ampere rating of the charger as specified in the table below.

AC INPUT RATING IN AMPERES

Equal to or greater than But less than

LENGTH OF CORD,

FEET (m)

AWG SIZE

OF CORD

2A 3A 25 (17.6)

50 (15.2)

100 (30.5)

6. Do not operate charger with damaged cord or plug – replace the cord or plug immediately.

7. Do not operate charger if it has received a sharp blow, been dropped,or otherwise damaged in any way;

take it to a qualified serviceman.

8. Do not disassemble charger; take it to a qualified serviceman when service or repair is required.

Incorrect reassembly may result in a risk of electric shock or fire.

9. To reduce risk of electric shock, unplug the charger from outlet before attempting any maintenance or cleaning.

Turning off controls will not reduce this risk.Clean only with slightly moist,not wet, cloth.Do not use solvents.

10. WARNING - RISK OF EXPLOSIVE GASES.

a) WORKING IN VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS. BATTERIES GENERATE EXPLOSIVE GASES

DURING NORMAL BATTERY OPERATION. FOR THIS REASON, IT IS OF UTMOST IMPORTANCE THAT YOU FOLLOW THE

INSTRUCTIONS EACH TIME YOU USE THE CHARGER.

b) To reduce risk of battery explosion, follow these instructions and those published by the battery manufacturer

and manufacturer of any equipment you intend to use in vicinity of the battery. Review cautionary marking on

these products and on engine.

11. PERSONAL PRECAUTIONS.

a) Someone should be within range of your voice OR close enough to come to your aid when you work near a lead-acid battery.

b) Have plenty of fresh water and soap nearby in case battery acid contacts skin, clothing or eyes.

c) Wear complete eye protection and clothing protection. Avoid touching eyes while working near battery.

d) If battery acid contacts or enters eye, flood eye with cold running water for at least 10 minutes and get medical

attention immediately. If battery acid contacts skin or clothing, wash immediately with soap and water. If acid enters

an eye, immediately flood eye with running cold water for at least 10 minutes and get medical attention immediately.

e) NEVER smoke or allow a spark or flame in vicinity of battery or engine.

f) Be extra cautious to reduce risk of dropping a metal tool onto battery. It might spark or short-circuit battery or other electrical

part that may cause explosion.

g) Remove personal metal items such as rings, bracelets, necklaces, and watches when working with a lead-acid

battery. A lead-acid battery can produce a short-circuit current high enough to weld a ring or the like to metal,

causing a severe burn.

i) NEVER charge a frozen battery.

SAFETY US & CAN

12. PREPARING TO CHARGE

a) If necessary to remove battery from vehicle to charge,always remove grounded terminal from battery first.

Make sure all accessories in the vehicle are off, so as not to cause an arc.

b) Be sure area around battery is well ventilated while battery is being charged. Gas can be forcefully

blown away by using a piece of cardboard or other non-metallic material as a fan.

c) Clean battery terminals. Be careful to keep corrosion from coming in contact with eyes.

d) Add distilled water in each cell until battery acid reaches level specified by battery manufacturer. This helps purge

excessive gas from cells. Do not overfill. For a battery without cell caps, such as valve regulated lead acid (VRLA) or absorbed glass

mat (AGM) batteries, carefully follow manufacturer’s recharging instructions.

e) Study all battery manufacturer’s specific precautions such as removing or not removing cell caps while charging

and recommended rates of charge.

f) Determine voltage of battery by referring to vehicle or battery user’s manual and BEFORE MAKING

THE BATTERY CONNECTIONS, MAKE SURE THAT THE VOLTAGE OF THE BATTERY YOU ARE GOING TO

CHARGE MATCHES THE OUTPUT VOLTAGE OF THE CHARGER.

13. CHARGER LOCATION.

a) Locate charger as far away from battery as DC cables permit.

b) Never place charger directly above batterv being charged; gases from battery will corrode and damage the charger.

c) Never allow battery acid to drip on charger when reading gravity or filling battery. Do not operate charger in a closed-in area or

restrict ventilation in any way.

d) Do not set a battery on top of charger. IMPORTANT : Place charger on a hard flat surface or mount onto a vertical surface. Do not

place on plastic, leather or textile surface.

14. DC CONNECTION PRECAUTIONS

a) Connect and disconnect DC output clips only after setting any charger switches to off position and removing AC

cord from electric outlet. Never allow clips to touch each other, however should this happen no damage will result to

the charger circuit & the automatic charging programme will just reset to «start».

b) Attach clips to battery and chassis as indicated in 15(e), 15(f), and 16(b) through 16(d).

NOTE : This battery charger has an automatic safety feature that will prevent it from operating if the

battery has been inversely connected. Set charger switches to off position and/or remove AC cord from electrical outlet,

disconnect the battery clips, then reconnect correctly according to the instructions below.

15. FOLLOW THESE STEPS WHEN BATTERY IS INSTALLED IN VEHICLE. A SPARK NEAR A BATTERY MAY CAUSE BATTERY

EXPLOSION. TO REDUCE RISK OF A SPARK NEAR BATTERY :

a) Position AC and DC cords so as to reduce risk of damage by hood, door or moving engine part.

b) Stay clear of fan -blades, belts,pulleys,and other parts that can cause injury to persons.

c) Check polarity of battery posts.POSITIVE (POS, P, +) battery post usually has larger diameter than NEGATIVE (NEG,

N,–) post.

d) Determine which post of battery is grounded (connected) to the chassis. If negative post is grounded to chassis

(as in most vehicles), see (e). If positive post is grounded to the chassis, see (f).

e) For negative-grounded vehicle, connect POSITIVE (RED) clip from battery charger to POSITIVE (POS, P, + )

ungrounded post of battery. Connect NEGATIVE (BLACK) clip to vehicle chassis or engine block away from battery.

Do not connect clip to carburetor, fuel lines, or sheet-metal body parts. Connect to a heavy gage metal part of the

frame or engine block.

f) For positive-grounded vehicle, connect NEGATIVE (BLACK) clip from battery charger to NEGATIVE (NEG. N , -)

ungrounded post of battery. Connect POSITIVE (RED) clip to vehicle chassis or engine block away from battery.

Do not connect clip to carburetor, fuel lines, or sheet-metal body parts. Connect to a heavy gage metal part of the

frame or engine block.

g) When disconnecting charger, turn switches to off, disconnect AC cord,remove clip from vehicle chassis,and then

remove clip from battery terminal.

h) See operating instructions for length of charge information.

16. FOLLOW THESE STEPS WHEN BATTERY IS OUTSIDE VEHICLE. A SPARK NEAR THE BATTERY MAY CAUSE BATTERY

EXPLOSION. TO REDUCE RISK OF A SPARK NEAR BATTERY :

a) Check polarity of battery posts. POSITIVE (POS, P, +) battery post usually has a larger diameter than NEGATIVE

(NEG,N, -) post.

b) This battery charger has an automatic safety feature that will prevent it from operating if the

battery has been inversely connected. The charger does not allow charge current unless a voltage of

at least 2V is sensed.

c) Connect POSITIVE (RED) charger clip to POSITIVE (POS, P, +) post of battery.

d) Connect NEGATIVE (BLACK) charger clip to NEGATIVE (NEG, N, -) battery post of the battery.

e) Do not face battery when making final connection.

f) When disconnecting charger, always do so in reverse sequence of connecting procedure & break first connection

while as far away from battery as practical.

g) A marine (boat) battery must be removed & charged on shore. To charge it on board requires equipment specially

designed for marine use.

SAFETY US & CAN

Especificaciones del producto

Marca:	Tecmate
Categoría:	cargador de bateria
Modelo:	Optimate 6 Ampmatic

¿Necesitas ayuda?

Si necesitas ayuda con Tecmate Optimate 6 Ampmatic haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

cargador de bateria Tecmate Manuales

Tecmate OPTIMATE 5 TM 221 Manual de Usario

8 Septiembre 2024

Tecmate Optimate 5 Voltmatic - TM222 Manual de Usario

8 Septiembre 2024

Tecmate OPTIMATE 5 TM 220 Manual de Usario

8 Septiembre 2024

Tecmate Optimate Lithium - TM290 Manual de Usario

8 Septiembre 2024

Tecmate Optimate 3+ Manual de Usario

8 Septiembre 2024

Tecmate Optimate Lithium - TM291 Manual de Usario

8 Septiembre 2024

Tecmate ACCUMATE PRO Manual de Usario

8 Septiembre 2024

Tecmate ACCUMATE Manual de Usario

8 Septiembre 2024

Tecmate Optimate Pro 2 Manual de Usario

8 Septiembre 2024

Tecmate ACCUMATE PRO 5 Manual de Usario

8 Septiembre 2024

cargador de bateria Manuales

Últimos cargador de bateria Manuales

Nitecore UHX1 PRO Manual de Usario

27 Octubre 2024

Nitecore EMR05 TAC Manual de Usario

26 Octubre 2024

Bosch GAA12V-21N Manual de Usario

24 Octubre 2024

Panasonic CF-VCB331 Manual de Usario

24 Octubre 2024

Ryobi One+ RC18627 Manual de Usario

21 Octubre 2024

Alecto BL-179 Manual de Usario

19 Octubre 2024

Graupner Ultramat 12 Manual de Usario

16 Octubre 2024

Graupner ULTRA DUO PLUS 30 Manual de Usario

16 Octubre 2024

MSW S-CHARGER-20A.2 Manual de Usario

15 Octubre 2024

MSW S-CHARGER-10A.2 Manual de Usario

15 Octubre 2024