VDO 190-903 Manual de Usario

VDO Equipo de medición 190-903

Lee a continuación 📖 el manual en español para VDO 190-903 (2 páginas) en la categoría Equipo de medición. Esta guía fue útil para 5 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

Ammeter

Installation Instructions

Instruction Sheet #0 515 012 154

Rev. 10/09

INSTRUCTIONS FOR THE INSTALLATION OF THE AMMETER ARE CONTAINED HEREIN.

USE IS RESTRICTED TO 12-VOLT NEGATIVE GROUND ELECTRICAL SYSTEMS. LIGHT

BULB, IF SUPPLIED, IS 12 VOLT.

S i e m VDO

Tools and Materials Needed For Installation:

10 Gauge stranded, insulated wire

Ring terminals

Non-insulated ¼" spade connectors

2¹⁄₁₆" hole saw

Drill and drill bit set

Half-round file

Tape measure or ruler

Small tools: wrench or nut driver, utility

knife, pliers, etc.

Ammeter Installation:

To Begin, go to #➊

➊BEGIN HERE

1. Select the location where you will mount

the gauge, and mark a center point.

1. Run a series of wires from the ammeter

location through the firewall to:

a) the positive (+) terminal on

the alternator;

b) the positive (+) terminal on

the starter;

Wiring the Ammeter:

[text continues at # Ë]

The bezel diameter is only a few mil-

limeters larger than the gauge itself.

With that in mind, measure and pre-

cisely mark the gauge location be-

fore cutting any holes!

CAUTION!!!

2. Cut a 2¹⁄₁₆" (52 mm) diameter hole for

the gauge. Make sure the hole is no larger

than 2 ¹⁄₁₆" (52 mm). If the gauge is too

snug, use a file to slightly enlarge the open-

ing. (Diagram A)

3. Slip the mounting bracket over the

mounting bolts on the back of the gauge.

Screw on the accompanying nuts. Tighten

the nuts until the ammeter can no longer

be rotated by hand. (Diagram B)

DO NOT OVERTIGHTEN.

Item Description Quantity

1. Ammeter (2 ¹⁄₁₆" [52 mm] diameter) 1

2. Lamp Socket (Push in, wedge-type) 1

3. Light Bulb (12-volt / G.E. #158 or equivalent) 1

4. VDO Mounting Bracket and nuts (2) 1

5. Installation Instructions 1

Parts List

Diagram D

Proper wiring of the VDO Ammeter

/ %

9W^YdY_^CgYdSXUT!"f

<_QT

CdQbdUb1\dUb^Qd_b 7b_e^T

2QddUbi

1]]UdUb 6ecU2_h

<YWXd

CgYdSX

Note: We recommend this instrument be

installed by a trained professional.

CAUTION:

Read these instructions

thoroughly before making installation.

Do not deviate from assembly or wiring

instructions. Always disconnect battery

ground before making any electrical

connections. If in doubt, please contact

your dealer or VDO at 1-800-265-1818.

➋CONTINUE HERE

Diagram A

Gauge dimensions

Diagram B

Proper mounting of the VDO Ammeter

c) the positive (+) terminal on

the ignition switch.

2. Connect the wires from the alternator,

starter and ignition to the terminals on the

back of the ammeter as shown in Diagram

At this point, the installation and wiring

of your ammeter is complete. Turn on the

ignition and start the engine to be sure the

ammeter is working properly. If it isnt, re-

check your wiring.

3. Connect the wire from the light switch

(after the fuse box) and from a ground lo-

cation to the ammeter light switch termi-

nals, also as shown in Diagram C.

PD[   PP

  PP

 é  PP

   PP



   PP

Especificaciones del producto

Marca:	VDO
Categoría:	Equipo de medición
Modelo:	190-903
Color del producto:	Zwart
Amable:	AV-receiver
Resolución Máxima:	1920 x 1440 Pixels
Certificados de sostenibilidad:	RoHS
Temperatura de almacenamiento:	-10 - 70 °C
Dimensiones (Ancho x Fondo x Alto):	55 x 61 x 25 mm
Puertos de entrada RJ-45:	1
Puertos de salida VGA (D-Sub):	1
Rango-maximo:	180 m
Temperatura de funcionamiento (TT):	0 - 40 °C
Humedad relativa de funcionamiento (VV):	0 - 95 procent
Tipos de cables compatibles:	Cat5e, Cat6