Draper 137052 Manual de Usario

Draper pantalla de proyección 137052

Lee a continuación 📖 el manual en español para Draper 137052 (1 páginas) en la categoría pantalla de proyección. Esta guía fue útil para 15 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/1

Installation Instructions

Salara/Series M by Draper

Wall/Ceiling Flush Mounting

➀

Attach Mounting Brackets to wall or ceiling (see Fig. 1). The installer should

furnish screws, toggle bolts, molly bolts, nylon or lead anchors as required

by the mounting surface. Installer also needs to ensure the mounting

surface is reinforced sufﬁ ciently to support the screen. Brackets must be

level with each other.

Figure 1

Figure 3

If you encounter any difﬁ culty installing or ser vic ing your Salara, call your dealer

or Draper, Inc., Spiceland, Indiana, (765) 987-7999; or fax (765) 987-7142.

Wall

Mounting

Bracket

11/ "2

➁ Attach the screen by snapping the extrusions on the back of the case onto

the brackets. With the lower edge of the screen case tilted away from the

wall, engage the rib on top of the case with the slot on each bracket. Slide

the screen case along the brackets to adjust the screen location from left to

right if necessary (see Fig. 2). Once the case is in position, pivot the case

back toward the brackets until the lower edge of the case "snaps" into place

with the spring-loaded latch (see Fig. 3).

Extrusions along

back of case

Dimensions

311/ "16

5/ "16

3/ "8

13/ "8

Case Length

Vie ing S rfacew u

51/ "16

/ "16

31/ "8

37/ "16

5/ "16

313/ "16

Floating Mo nting Bracketsu

Figure 2

12 3

Mounting

Bracket

11/ "2

Ceiling

Operating Instructions—Standard

To lower picture surface, pull screen down. —then allow screen to Hesitate

retract very slowly until it locks in place.

To raise picture surface, pull screen down and, while holding, allow for slow

retraction into the case to reduce risk of injury from falling screen.

Operating Instructions—AutoReturn

To lower picture surface, pull screen down. —then allow screen to Hesitate

retract very slowly until it locks in place.

To raise picture surface, pull screen down gently until it stops, then release.

Matt White & High Contrast Grey

Clean surface with a solution of mild dishwashing liquid diluted with warm

water. Sponge the surface, rinse with clear water and blot dry. Do not use

clean ing solvents or abrasives.

Viewing Surface Care & Maintenance

Glass Beaded

Clean with a very soft brush or cloth and care ful ly dust the surface. DO

NOT USE SOAP, WATER, SOLV VENTS OR ABRASI ES. These substances

will damage a glass beaded viewing surface.

Caution

➀ Read and understand these instructions; keep them for future reference.

Follow instructions carefully.

➁ Care in both mounting and correct operation will mean long and satis-

factory service from your Draper screen.

➂ Locate the screen where the audience can best see it, and where other

room fur nish ings permit.

➃ Mount the screen so that the bottom of the picture, when screen is fully

extended, will be above the heads of viewers.

➄ When raising screen, pull down and, while holding, allow for slow

retraction into the case to reduce risk of injury from falling screen.

➅ Screen should be installed level (using a carpenter’s level).

➆ Nothing should be fastened to screen dowel or viewing surface.

NOTE: Screen has been thoroughly inspected and tested at factory and

found to be operating prior to shipment.

Especificaciones del producto

Marca:	Draper
Categoría:	pantalla de proyección
Modelo:	137052
Color del producto:	Roestvrijstaal
Amable:	Installatieset
Cantidad por paquete:	2 stuk(s)
Compatibilidad de marca:	Siemens
Longitud:	815 mm