Eastron SDM630-EV Manual de Usario

Eastron Equipo de medición SDM630-EV

Lee a continuación 📖 el manual en español para Eastron SDM630-EV (2 páginas) en la categoría Equipo de medición. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

1. Introduction

The SDM630-EV V2 measures and displays the

characteristics of single phase two wires (1p2w),

three phase three wires (3p3w,) and three phase four

wires(3p4w) supplies, including voltage, frequency,

current, power ,active and reactive energy, imported or

exported. Energy is measured in terms of kWh, kVArh.

Maximum demand current can be measured over preset

periods of up to 60 minutes. In order to measure energy,

the unit requires voltage and current inputs in addition to

the supply required to power the product.

SDM630-EV V2 supports max. 100A direct connection,

saves the cost and avoid the trouble to connect external

CTs, giving the unit a cost-effective and easy operation.

Built-in interfaces provides pulse and RS485 Modbus RTU

outputs. Conﬁguration is password protected.

1.2 Measured Parameters

The unit can monitor and display the following parameters

of a single phase two wire(1p2w), three

phase three wire(3p3w) or four phase four wire(3p4w)

supply.

1.3 Voltage and Current

Phase to neutral voltages 100 to 289V a.c.

(not for 3p3w supplies)

Voltages between phases 173 to 500V a.c.

(3p supplies only)

Percentage total voltage harmonic distortion (THD%) for

each phase to N ( not for 3p3w supplies)

Percentage voltage THD% between phases (three phase

supplies only)

Current THD% for each phase

1.4 Power Factor and

Frequency and Max. Demand

Frequency in Hz

Instantaneous power:

Power 0 to 99999 W

Reactive Power 0 to 99999 VAr

Volt-amps 0 to 99999 VA

Maximum demanded power since last Demand reset

Power factor

Maximum neutral demand current, since the last Demand

reset (for 3p4w supply only)

1.5 Energy Measurements

• Imported active energy 0 to 999999.99 kWh

• Exported active energy 0 to 999999.99 kWh

• Imported reactive energy 0 to 999999.99 kVArh

• Exported reactive energy 0 to 999999.99 kVArh

• Total active energy 0 to 999999.99 kWh

• Total reactive energy 0 to 999999.99 kVArh

1.6 Measured Inputs

Voltage inputs through 4-way ﬁxed connector with 25mm²

stranded wire capacity. single phase two wire(1p2w), three

phase three wire(3p3w) or four phase four wire(3p4w)

unbalanced. Line frequency measured from L1 voltage or

L3 voltage.

1.7 Accuracy

• Voltage 0·5% of range maximum

• Current 0·5% of nominal

• Frequency 0·2% of mid-frequency

• Power factor 1% of unity (0.01)

• Active power (W) ±1% of range maximum

• Reactive power (VAr) ±1% of range maximum

• Apparent power (VA) ±1% of range maximum

• Active energy (Wh) Class 1 IEC 62053-21

Class B EN50470-1/3

• Reactive energy (VArh) Class 2 IEC 62053-23

• Response time to step input 1s, typical, to >99% of

ﬁnal reading, at 50 Hz.

SDM630-EV

DIN Rail Smart Meter for Single and

Three Phase Electrical Systems

The interface performs a

self-test and indicates the

result if the test passes.

The second screen

indicates the ﬁrmware

installed in the unit and its

build number.

*The build number(41

01.00) is for reference only.

The actual build number

changes according to

product requirements.

Meter SN, Modbus ID and

baud rate setting

If you have any question, please feel free to contact our sales team. Tel: 0203 758 3494 Email: sales@eastroneurope.com www.eastrongroup.com

Warnings

Important Safety Information is contained in the

Maintenance section. Familiarize yourself with this

information before attempting installation or other

procedures. Symbols used in this document:

Risk of Danger: These instructions contain

important safety information. Read them before

starting installation or servicing of the equipment.

Caution: Risk of Electric Shock

• Measures kWh Kvarh, KW, Kvar, KVA, P, F,

PF, Hz, dmd, V, A, etc.

• Bi-directional measurement IMP & EXP

• Pulse output

• RS485 Modbus

• Din rail mounting 35mm

• 100A direct connection

• Better than Class 1 / B accuracy

1.8 Interfaces for External

Monitoring

Three interfaces are provided:

• 2 RS485 communication channels via protocol remotely.

• Pulse output indicating real-time measured energy.

1.9 Pulse Output

Pulse output is non-conﬁgurable. It is ﬁxed up with active

kWh. The constant is 400imp/kWh.

1.10 RS485 Output for

Modbus RTU

There 2 two channels of RS485 Modbus RTU.

For Modbus RTU, the following RS485 communication

parameters can be conﬁgured from the

Set-up menu:

• 1st Modbus Output (conﬁgurable):

2400, 4800, 9600(default), 19200, 38400 Baud rate

none (default)/odd/even Parity

1 or 2 Stop bits

RS485 network address nnn – 3-digit number,

001 to 247

• 2nd Modbus Pitput (non-conﬁgurable):

9600 Baud rate

none Parity

1 Stop bits

Modbus™ Word order Hi/Lo byte order is set

automatically to normal or reverse. It cannot be

conﬁgured from the set-up menu.

1.11 Reference Conditions of

Inﬂuence Quantities

Inﬂuence Quantities are variables that affect measurement

errors to a minor degree. Accuracy is

veriﬁed under nominal value (within the speciﬁed tolerance)

of these conditions.

• Ambient temperature 23°C ±1°C

• Input frequency 50Hz(MID)

50 or 60Hz ±2%

(non- MID)

• Input waveform Sinusoidal (distortion

factor < 0·005)

• Magnetic ﬁeld of external origin Terrestrial ﬂux

1.12 Environment

• Operating temperature 3K6(-25°C to

+55°C*),Default

3K7(-40°C to +70°C*)

• Storage temperature -40°C to +70°C*

• Relative humidity 0 to 90%, non-

condensing

• Altitude Up to 2000m

• Warm up time 5S

• Vibration 10Hz to 50Hz,

IEC 60068-2-6, 2g

• Shock 30g in 3 planes

* Maximum operating and storage temperatures are in the context of

typical daily and seasonal variation.

1.13 Unit Characteristics

The Unit can measure and display:

• Line voltage and THD% (total harmonic distortion)

of all phases

• Line Frequency

• Currents, Current demands and current THD% of

all phases

• Power, maximum power demand and power factor

• Active energy imported and exported

• Reactive energy imported and exported

The unit has password-protected set-up screens for:

• Changing password

• Supply system selection 1p2w, 3p3w,3p4w

• Demand Interval Time(DIT)

• Reset for demand measurements

The pulse output indicates real-time energy measurement.

2 RS485 outputs allows remote monitoring from another

display or a computer.

2. Start-up Screens

Selects the Voltage and Current display screens

In Set-up Mode, this is the “Left” or “Back” button.

Select the Frequency and Power factor display

screens

In Set-up Mode, this is the “Up” button

Select the Power display screens

In Set-up Mode, this is the “Down” button

Select the Energy display screens

In Set-up mode, this is the “Enter” or “Right” button

After a short delay, the screen will display active energy

measurements.

2.1 Measurements

The buttons operate as follows:

2.2 Voltage and Current

Each successive pressing of the button selects

a new range:

Phase to neutral

voltages(3p4w)

Phase to neutral

voltages(3p3w)

Current on each phase

Neutral current

2.3 Frequency and Power

Factor and Demand

Each successive pressing of the button selects

a new range:

Power Factor

Maximum Current Demand

Maximum Power Demand

2.4 Power

Each successive pressing of the button selects

a new range:

Instantaneous Active

Power in W

Instantaneous Reactive

Power in VAr

Instantaneous Volt-amps

in VA

Total W, VArh, VA

2.5 Energy Measurements

Each successive pressing of the button selects

a new range:

Total kWh and time will be

showed when no charging

Total kWh and charged

kWh will be showed when

charging

CSID Numbers And current

time will be showed when

charging

Total active kWh, import

active kWh, export active

kWh

Total reactive kWh, import

reactive kWh, export

reactive kWh

2.6 Set-up

To enter set-up mode, pressing the button for 3

seconds, until the password screen appears.

Setting up is password-protected so you must enter the

correct password (default ‘1000’) before processing. If

an incorrect password is entered, the display will show:

PASS Err

To exit setting-up mode, press repeatedly until

the measurement screen is restored.

Setting - Button operation

3 Set-up Entry Methods

Some menu items, such as password, require a four-digit

number entry while others, such as supply system, require

selection from a number of menu options.

3.1 Menu Option Selection

1) Use the and buttons to select the

required item from the menu. Selection does not roll over

between bottom and top of list.

2) Press to conﬁrm your selection.

3) If an item ﬂashes, then it can be adjusted by the

and buttons. If not, there maybe a further layer.

4) Having selected an option from the current layer press

to conﬁrm your selection. The SET indicator will appear.

5) Having completed a parameter setting, press to

return to a higher menu level. The SET indicator will be

removed and you will be able to use the and

buttons for further menu selection.

6) On completion of all set-up, press repeatedly

until the measurement screen is restored.

3.2 Number Entry Procedure

When setting up the unit, some screens require the

entering of a number. In particular, on entry to the setting

up section, a password must be entered. Digits are set

individually, from left to right.

The procedure is as follows:

1) The current digit to be set ﬂashes and is set using

the and buttons.

2) Press to conﬁrm each digit setting. The SET

indicator appears after the last digit has been set.

3) After setting the last digit, press to exit the

number setting routine.

3.3 Main set

System type From the Set-up menu, use and

buttons to select the System option. The screen

will show the currently selected system type.

Password Use the and to choose the change

password option.

Reset Press to enter the selection routine. If succeed,

the cursor will jump back to Reset.

Press to exit the number setting routine and return to the

Set-up menu. SET will be removed.

3.4 Communication set

Addr From the Set-up menu, use and

buttons to select the Address ID.

Baud From the Set-up menu, use and

buttons to select the Baud Rate option.

Parity From the Set-up menu, use

and

buttons to select the Parity option.

3.5 Time set

Data From the Set-up menu, use and

buttons to select the data.

Use to move cursor

Time From the Set-up menu, use

and

buttons to select the data.

Use to move cursor

DMD From the Set-up menu, use

and

buttons to select the dmd. Setting options: 0, 5,

8, 10, 15, 20, 30, 60

ZONE From the Set-up menu, use

and

buttons to select the ZONE. Setting range:-12~12

Backlight From the Set-up menu, use and

buttons to select the Backlight. Setting options:

on,10, 30, 60, 120, off

Use and buttons to select the time interval. Press

to conﬁrm the set-up.

3.6 Record

Record From the Set-up menu, use and

buttons to select record data.

Max.: lastest 10 records

Use and buttons to select the time interval.

1.Main

1.1Sytem Type 3P4W

1.2Password 1000

1.3Reset DMD

2.Communication

2.1Addr 002

2.2Baud 9600

2.3Parity NONE

4.Time

4.1Data 14-01-30

4.2Time 08-15-14

4.3DMD 60

4.Time

4.4ZONE +08

4.5Backlight 060

5.Record

CSID:20140130000005

T: 00:00:03

C: 000006wh

PASSWORD :

0 0 0 0

User Manual

2022 V1.0

If you have any question, please feel free to contact our sales team. Tel: 0203 758 3494 Email: sales@eastroneurope.com www.eastrongroup.com

4. Wiring diagram

• Three Phase Three Wires

If you have any question, please feel free to contact our

sales team.

Eastron Europe Limited; Suite 20 Cornwallis House, Howard Chase, Basildon,

Essex SS14 3BB.

Tel: 0203 758 3494

Email: sales@eastroneurope.com

www.eastrongroup.com

EU Declaration of Conformity

We, Zhejiang Eastron Electronic Co LTD

No.1369,Chengnan Rd. Jiaxing, Zhejiang, China 314001,

Ensure and declare that electricity meter types:

SDM630- EV

with the measurement range

1. 3 x 230/400V 50Hz, - 0.5 10(100)A 400imp/ kWh.

Are in conformity with the type as described the - examination in EU type certificate

0120/ SGS0151

The fulfillment the essential requirements Annex I the relevant of set out in and in

instrument specific Annexes has been demonstrated.

The electricity meter described conformity with the types above are in relevant Union

harmonization legislation and satisfy the appropriate requirements of the Directive

2014/32/EU with the following standards:

EN50470 1:2006,- Electricity equipment (AC) part metering 1: General requirements,

tests and test conditions. Metering equipment (class indexes A, B and C)

EN50470 3:2006,- Electricity equipment (AC) Part metering 3: Particular requirements-

Static meters for active energy (class indexes A, B and C)

This Declaration of issued the Conformity is under sole responsibility of the

manufacturer.

Signed behalf Zhejiang Eastron Electronic Co., on of LTD.

Signature:

Date: - - 2022 07 05

Position: General Manager

8. EU Declaration of Conformity

7. MID Certiﬁcate

• Three Phase Four Wires

• Single Phase Two Wires

5. Dimensions

6. Wiring Torque

Especificaciones del producto

Marca:	Eastron
Categoría:	Equipo de medición
Modelo:	SDM630-EV

¿Necesitas ayuda?

Si necesitas ayuda con Eastron SDM630-EV haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

Equipo de medición Eastron Manuales

Eastron SDM630-EV Manual de Usario

16 Septiembre 2024

Eastron SDM54-M Manual de Usario

13 Septiembre 2024

Eastron SDM530Y Manual de Usario

3 Agosto 2024

Equipo de medición Manuales

Últimos Equipo de medición Manuales

PeakTech 1207 Manual de Usario

26 Octubre 2024

Kern FL 1KG Manual de Usario

25 Octubre 2024

PeakTech 6193 Manual de Usario

25 Octubre 2024

PCE Instruments PCE-TUM 50 Manual de Usario

24 Octubre 2024

PCE Instruments PCE-325D Manual de Usario

23 Octubre 2024

PCE Instruments PCE-AM 30 Manual de Usario

23 Octubre 2024

PCE Instruments PCE-900 Manual de Usario

23 Octubre 2024

PCE Instruments PCE-CSM 10 Manual de Usario

23 Octubre 2024

PCE Instruments PCE-CSM 7 Manual de Usario

23 Octubre 2024

PCE Instruments PCE-CSM 3 Manual de Usario

23 Octubre 2024