Olympia PR 1 Manual de Usario

Olympia Cámara de vigilancia PR 1

Lee a continuación 📖 el manual en español para Olympia PR 1 (3 páginas) en la categoría Cámara de vigilancia. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/3
25 (optional) 24
68910 11 12 13 14
15
18
20
16
17
3
2
1
19
21 (hidden)
22
4/5
23
7
Figure
Reinforced Lock Bar PR 1
Assembly Manual
Reinforced Lock Bar PR 1
■Anti-burglary protection for inward opening doors
■Secures the door on the lock and hinge sides
■Protection against break-ins from the outside
■Bolt throw of 80 mm with one turn of the key
■Lockable from the inside and outside
■Prepared for a prole double cylinder
■30/55 mm prole double cylinder included in the
package for door thickness of 40 mm
Subject to change without prior notice.
Reinforced Lock Bar PR 1
v1.0, 10.2018
Art. No. 7045
Preparing for a Prole Double Cylinder
Assembling the Reinforced Lock Bar Assembling the Strike Plates
General
Assembly Information
*Suitable prole double cylinder
Door thickness Version
40 mm 30/55 mm
45 mm 30/60 mm
50 mm 30/65 mm
55 mm 30/70 mm
60 mm 30/75 mm
65 mm 30/80 mm
70 mm 30/85 mm
75 mm 30/90 mm
Area of use for
door leaf width
800 to 950 mm
Lock bar Triple adjustment on both sides
Bolt throw 80 mm with one turn of the key, lockable
from inside and outside
outside inside
min. 12 + door width 30
1 Remove the housing cover (7) from the reinforced
lock bar and lay it with its inner side centred on the
door leaf so that the distance to the edges of the
door leaf are the same.
Before beginning any assembly work, ensure
that the reinforced lock bar is suitable for the
structural conditions. Order an appropriate
prole double cylinder, if necessary.
To prevent overtightening the retaining
screws, tighten them by hand using an ap-
propriate screwdriver.
Read the assembly manual thoroughly and observe the information contained
during installation. Keep the assembly manual in a safe place for future refer-
ence.
Scope of Delivery
Technical Data
Tools Required
387
Check the package supplied is complete:
■1x reinforced lock bar (1)
■1x 30/55 mm prole double cylinder for a
door thickness of 40 mm (22)
■ 2x side pieces, plastic (6)
■ 1x outside escutcheon PZ, metal (16)
■ 1x inside escutcheon, plastic (15)
■ 2x spring washer (23)
■ 2x screw M5x35 (17)
■ 4x screw M5x15 (20)
■ 4x screw M4x10 (cylinder head) (19)
■ 4x screw M6x75 (10)
■ 4x dowel 8x40 (8)
■ 2x expansion dowel 10x112 (9)
■ 2x strike plate (13) with cover (14)
■ 12x spacer plate 2 mm (11)
■ 2x spacer plate 12 mm (12)
■ 3x key
20
22
4
5
18
21 (hidden)
8
11
12
13 10
9
6
Intended Use
The PR1 reinforced lock bar provides additional protection against unauthorised access to rooms. It is intended for inward opening doors made
of wood, metal and plastic with widths between 800 and 950 mm. The best protective eect can only be achieved when you complete the instal-
lation according to this assembly manual.
A condition for complying with the intended use is that the equipment is installed correctly and the information in the manual is observed and
maintained.
Any other use is considered unintended use. Unauthorised modication or reconstruction not described in this assembly manual are not permit-
ted and could cause the product to be damaged.
■Various screwdrivers
■Drill
■Metal bits: Ø 13.0mm
(also for use with wood)
Ø13.5mm, Ø15.0mm,
Ø18.5mm, Ø10.0mm
■Masonry bits: Ø 10.0mm,
min. 180mm
■Hole cutter/saw: Ø 35 mm
■Spirit level, tape measure
2 Mark the position for the hole for the cylinder and
drill a hole with a diameter of 35 mm in the door
leaf at the required height.
Note: The distance to the centre of the
prole double cylinder is 387 mm.
If the prole double cylinder is already installed, continue with Step 10. Otherwise, assem-
ble the prole double cylinder as follows:
3 Remove the screws and spring washers (19) from the cylinder plate (18).
4 Remove the cylinder plate and remove the plastic insert.
5 Remove the cog wheel (4, 5) from under the cylinder plate.
6 Slide one part (4) of the cog wheel from the left and the other part (5)
from the right on the prole double cylinder. The broader segment
of the cog wheel parts must be against the lock bit (21) of the prole
double cylinder. Both parts, together with the locking catch, produce
an interlocking connection.
7 Insert the prole double cylinder in the cylinder plate (18) and x the
cylinder in place with the screw M5x15(20) and spring washer (23).
8 Slide the toothed rods (2, 3) against the stop so that the bar is in the
position it will be when opened later. The lock bit must run into the
wide recess of the toothed rod.
9 Now t the assembled cylinder with the cylinder plate in the rein-
forced lock bar and screw the plate tight with the screws and spring
washers (19).
You can now x the reinforced lock bar on the door:
10 Position the reinforced lock bar with the assembled prole double
cylinder so that the cylinder is in the hole in the door.
11 Align the bar using the spirit level and mark the two holes to x
the outside escutcheon (16).
12 Drill the holes using a bit with 12 mm Ø.
13 Reassemble the reinforced lock bar, slide the metallic outside
escutcheon (16), or the optionally available protective escutcheon
(SR 100 ZA) (25), on the outside of the door above the lock cylinder
and x the escutcheon using the spring washers and screws
M4x10 (19) (cylinder head).
1 Position the strike plates (13) at the height of the lock in the door
frame or on the wall on both sides.
Tip: When you lock the reinforced lock bar, you can slide the strike plate
over the extended lock bar. This simplies alignment.
2 Mark the holes.
3 Remove the strike plates, unlock the lock, drill the plug holes and
insert the wall dowels (8).
4 Place the necessary number of spacer plates (11, 12) between the wall
and strike plate until the lock bar slides into the strike plate easily and
without any strain. When doing so, pay attention that the "catches" of
the spacer plates engage in the corresponding recesses of the following
spacer plate.
5 Fix the strike plates in place with the screws M6x75 (10).
6 Now drill the holes for the expansion dowels (9). Insert the expansion
dowels and tighten them.
7 Finally, press the covers (14) on the strike plates (13).
Guarantee
The period of guarantee is 24 months. The period of guarantee
begins on the date of purchase. It is essential to keep the purchase
receipt and original packaging. If a problem arises, please refer to
our Return Merchandise Authorisation portal (RMA) in the Support
section of our website at www.olympia-vertrieb.de.
In the case of further queries, please contact our hotline
01805007514 (costs via German landline at time of going to
print: 14 ct/min., max. 42 ct/min. via a mobile network).
Olympia Business Systems Vertriebs GmbH
Zum Kraftwerk 1 - 45527 Hattingen
Disposal
Help protect the environment and dispose of the
product and packaging materials according to the
applicable local regulations.
Safety Instructions
Further Information
Further information on this product is available at
http://productip.com/?f=84f41
Or scan this QR code.
Avoid any personal injury by paying attention
to the following information!
WARNING! Risk of suoca-
tion! Children can swal-
low small parts, packag-
ing and protective foils.
Keep the product and
packaging out of reach of
children!
IMPORTANT! Improper assembly can
lead to property damage. Install
the reinforced lock bar as illus-
trated in this assembly manual.
Only use the assembly material
supplied.
Assembly Manual
Reinforced Lock Bar PR 1
Assembly Manual
Reinforced Lock Bar PR 1
Assembly Manual
Reinforced Lock Bar PR 1
14 Check the alignment using a spirit level and then mark the holes
on the ends (24).
15 Drill the holes and x the reinforced lock bar on the door leaf
using the screws M5x35 (17).
16 Replace the cover (7) and press in the side pieces (6) and the plas-
tic inside escutcheon (15).
A large diagram is provided on the rear side to help you arrange the
individual elements.

Especificaciones del producto

Marca: Olympia
Categoría: Cámara de vigilancia
Modelo: PR 1

¿Necesitas ayuda?

Si necesitas ayuda con Olympia PR 1 haz una pregunta a continuación y otros usuarios te responderán


Cámara de vigilancia Olympia Manuales

Olympia

Olympia OC 1280P Manual de Usario

27 Octubre 2024
Olympia

Olympia 5939 Manual de Usario

27 Octubre 2024
Olympia

Olympia TV 200 Manual de Usario

9 Septiembre 2024
Olympia

Olympia DC400 Manual de Usario

30 Agosto 2024
Olympia

Olympia BMD 210 Manual de Usario

28 Agosto 2024
Olympia

Olympia T300 Manual de Usario

27 Agosto 2024
Olympia

Olympia WSL 10 Manual de Usario

27 Agosto 2024
Olympia

Olympia Protect 9065 Manual de Usario

27 Agosto 2024
Olympia

Olympia Protect 5080 Manual de Usario

26 Agosto 2024
Olympia

Olympia WL 100 Manual de Usario

26 Agosto 2024

Cámara de vigilancia Manuales

Últimos Cámara de vigilancia Manuales

Speco Technologies

Speco Technologies WDRB11H Manual de Usario

27 Octubre 2024
Vivotek

Vivotek AI-108 Manual de Usario

27 Octubre 2024
Acti

Acti E88 Manual de Usario

27 Octubre 2024
Yale

Yale WIPC-303W Manual de Usario

27 Octubre 2024
Grandstream

Grandstream GXV3611IR_HD Manual de Usario

27 Octubre 2024
Airlive

Airlive DM-720 Manual de Usario

27 Octubre 2024
Speco Technologies

Speco Technologies O8B7M Manual de Usario

27 Octubre 2024
Grandstream

Grandstream GXV3615W Manual de Usario

27 Octubre 2024
Vivotek

Vivotek IP8133 Manual de Usario

27 Octubre 2024
Acti

Acti E39 Manual de Usario

27 Octubre 2024