Pyle PDWM5900 Manual de Usario

Pyle micrófono PDWM5900

Lee a continuación 📖 el manual en español para Pyle PDWM5900 (4 páginas) en la categoría micrófono. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/4
RECEIVER
Frequency: 902~926.75MHz
Frequency Stability 10ppm
Sensitivity: 13dBuV
Adjacent channel rejection 75dB
Image rejection: 95dB
Audio Output 200MV
Output Impedance: XLR connector: 200 ; 1 / 4 inch connector: 1kΩ Ω
S/N ratio: 100dB
0.1%
Frequency response: 50Hz-15KHz
: 60m
Power supply: DC12V--18V
Housing: Metal
Size(WxDxH): 16.5”x7”x1.8”
Weight: 3.3 lbs
MICROPHONE
Frequency: 902~926.75MHz
Frequency Stability: 10ppm
Transmitting power: <10mW
Spurious emission: >65dB
Modulation: FM
Max modulation: 75K
Power supply: 3V (2 AA batteries)
Current consumption: 120mA
Total Harmonic Distortion: <
Operating Range
SPECIFICATIONS
FRONT PANEL
1. CH- A Volume control
2. CH-A channel UP
3. CH-A channel DOWN
4. Infrared (IR) port
5. CH-A Sync Button
6. CH-A display
REAR PANEL
13. Antenna jack B
14. Balanced XLR output jack B
15. Mixed 1 / 4 " output jack
16. DC input jack
17. Balanced XLR output jack A
18. Antenna jack A
RECEIVER
ANT-B ANT-A
BALANCED OUT B MIXE D OUT
13 14 15 16 17 18
1. Connect one end of supplied 6.35mm to 6.35mm plug audio cable
into MIXED OUT(15) on rear panel of the receiver. Connect the
other end of the audio cable into "MIC IN" or "AUX IN" of amplifier
or mixer.
2. Connect DC plug of supplied AC/DC adapter to DC INPUT(16) jack
on rear panel of the receiver. Connect AC plug of AC/DC adapter to
mains power socket.
3. Press POWER(12) button on front panel to turn on the receiver.
4. Press CH-A UP(2) or DOWN(3) buttons to set receiver CH-A
7. CH-B display
8. CH-B Sync Button
9. CH-B channel DOWN
10. CH-B channel UP
11. CH- B Volume control
12. Power On/Off switch
OPERATION
HANDHELD MIC
1. Mesh(capsule inside)
2. LCD display(IR port)
3. Power on/off switch
4. IR port
5. Battery cover/compartment
12 3 4
OPERATION
1. Open battery cover and install 2PCS AA batteries into battery
compartment with correct polarity(match + and - signs).
2. Press and hold power button to turn on microphone.
3. Point microphone IR port to receiver IR port and press CH-A SYNC
button to set first microphone frequency to be same as receiver CH-
A frequency. Press CH-B SYNC button to set second microphone
frequency to be same as receiver CH-B frequency.
4. Receiver RF indicator will display in receiver screen.
5. During operation if power LED indicator lights red, this indicates
the battery is Iow. Please replace new battery.
6. After use please press and hold power button to turn off
the microphone. If you are not going to use this system for a long
period of time please take out the batteries from
the microphone to avoid possible battery leakage which may
damage the microphone.
1 2 3 4 5 6 8 9 10 117 12
5
frequency. Then press CH-B
receiver CH-B frequency.
NOTE: Please must set CH-A and CH-B in different frequencies.
5. Adjust receiver volume(1, 11) and your amplifier or mixer volume to
suitable level.
UP(10) or DOWN(9) buttons to set

Especificaciones del producto

Marca: Pyle
Categoría: micrófono
Modelo: PDWM5900

¿Necesitas ayuda?

Si necesitas ayuda con Pyle PDWM5900 haz una pregunta a continuación y otros usuarios te responderán




micrófono Pyle Manuales

micrófono Manuales

Últimos micrófono Manuales