Pyle Pro PDWM2450 Manual de Usario

Pyle micrófono Pro PDWM2450

Lee a continuación 📖 el manual en español para Pyle Pro PDWM2450 (3 páginas) en la categoría micrófono. Esta guía fue útil para 7 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/3
SPECIFICATIONS
Audio Frequency Response: 50-15000Hz
Dynamic Range: ~
80dB
System Distortion:
~
1 %
Signal-la-Noise Ratio: ~
80dB
Operating Range: 50m-80m
Operating Temperature Range: 5
'C
-45
'C
Carrier
Frequency Range:
180-280MHz
Receiver:
Sensitiv / 3ity(S N= 0dB):
Image Rejection :
De-Emphasis:
Audio Output Impedance:
Audio
Out
put Level:
Power Supply:
Transmltter(hand-held):
Frequency Stability:
RF
Output power:
Spurious Rejection:
Modulation Mode:
Max v : imum De iation Range
Microphone Mode:
Pre-Emphasis:
Pow
er
Supply:
Transmitter(Lapel Microphone)
Frequency Stability:
RF Output power:
Spurious Rejection:
Modulation Mode:
Maximum Deviation Range:
Microphone Mode:
Pre-Emphasis:
Power Supply:
>2mV
>40dB
5,,"8
600
0±
10%
a-o
.
sv
AC110
V/
60Hz
± O.
005
%
~
30mW
>40dB
FM
± 75KHz
Dynamic
50""
2X1 .5V/9V BaHery
± O.005%
10mW
>40dB
FM
± 75KHz
Dynamic
50""
9VBattery
"*
O
••
lgn
and
specification
are
subject
to
change
without
notice
.
www.pyleaudio.com
PDWM
Wireless
2
Chann
el
VHF
Mi
crophone System
With
2
Mi
c ones roph
User
Manual
FEATURES
1.
Operating
on
VHF
high
band
frequency
within
180
to
280MHz.
The
other
frequency is not easy
to
bother.
2. Crystal-controlled circuit. And
the
antenna Inside
the
unite.
3. Dual channel receiver, one receiver can receiver
two
ttransmltter
at
the
same
time.
4. There Is a companding function.
5.
Audio output
Is
adjustable with volume control.
6. Audio Display.
RECEIVER
REMARK
1 .
Power
Switch 5. Audio
Output
Jack
of
A & 8 CH
2. Audio Display
6.
Audio Output Jack
of
A
CH
3.
Audio Volume
7.
Audio Output Jack
of
B
CH
4. Antenna
8.
AC Power Jack
TRANSMITTER
REMARK
o
D
j : D
1.
Mk><lphone
Head
7.
Microphone
Jack
2.
Grip
8. Microphone Input
Jack
3.
PCM'eI'Switch
9. PowerlSensitivity
SWitch
4.
Power IndlcatorlLow
Voltage
Indicator 10.
Belt
Clip
5.
Battery Canister
11
. Battery
Compartment
Cover
6.
Microphone Wire 12. Microphone Clip
OPERATION
1. Firstofall,
hook
up
powertothe
receiver
of this
system,
Tum
switch
ON
and
Power
Indicating light will
come
on
Indicating that power
Is
on, then hook up the connecting
wires attached as shown
in
the
drawing
and draw antenna fully.
2. Open
the
battery compartment cover
of
transmitter,
load
in
battery.
3. Tum
on
the power switch of microphone and
the
power Indicator will be light, that
the transmitter send the signal to the receiver.
4.
You
can adjust the volume to the middle or more through the volume knob, then
adjust the audio amplifier
to
the right position.
S.
When
the transmitter is
not
used, tum
the
powfer off.
6. When the receiver
Is
not used, tum the power off.
7. If the unit does
not
use for a
long
time,
you
must take
out
the battery.
ATTENTION
1.
You
had better Install your unit the place where cool and dry. do not Install
beside the window, and near the place where is too hot
or
too wet
or
too
much vibration
or
dust est.
2. Do not use force
on
switches, knobs
or
cords, When moving the set, first
turn the unit off.
3. Do not attempt to clean the unit with chemical solv : ents this might damage
the finish. Use a clean, dry cloth.
4.
If
you use several unit at the same time, you must use these unit in different
frequency.
S. Do not break the receiver and transmitter
of
microphone.

Especificaciones del producto

Marca: Pyle
Categoría: micrófono
Modelo: Pro PDWM2450

¿Necesitas ayuda?

Si necesitas ayuda con Pyle Pro PDWM2450 haz una pregunta a continuación y otros usuarios te responderán




micrófono Pyle Manuales

micrófono Manuales

Últimos micrófono Manuales