Trumeter HED261 Manual de Usario

Lee a continuación 📖 el manual en español para Trumeter HED261 (12 páginas) en la categoría Equipo de medición. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/12
HED261
8 digit counter with high speed count input
and optional backlighting
018359-01 Issue 1.3 January 2008
English
Page 2
Deutsch
Seite 4
Français
Page 6
Español
Página 8
8-stelliger Zähler mit schnellem Zähleingang
und optionaler Hintergrundbeleuchtung
Compteur totalisateur 8 chiffres, avec entrée
haute vitesse et rétroéclairage en option
Contador de 8 dígitos con entrada de
contaje de alta velocidad e iluminación
posterior opcional
Italiano
Pagina 10
Page 12
Seite 12
Pagina 12
Contatore a 8 cifre con input di conteggio
rapido e retroilluminazione facoltativa
Dimensions
Abmessungen
Dimensiones
Dimensioni
2
This counter is in two variants, HED261-R with reflective display and HED261-T with LED
backlight. Connection is via 2 sets of 3 pins at 0.1 inch pitch, spaced as shown.
The unit is fixed to the panel using the two spring clips which are integral to the housing.
The unit is the correct way up when the pins are at the bottom.
It can be powered from a higher DC voltage using the external circuit shown. For a 5v
supply omit the regulator. Use the regulator for a supply in the range 8 - 30v. The
regulator accommodates the different current requirements for the reflective and backlight
models.
Note:
This product is ideally suited to battery powered applications. Should the product be used
in a circuit where an external power source is used, then the complete system will require
separate approval to meet the CE standards.
Any signal cables connected to this device must not exceed 30 metres in length.
If signal cables are installed that are routed outside the building, it will be necessary to
install additional surge protection devices.
Display
8 digit, 8mm high contrast LCD
characters
Current consumption
Counting 6µA, standby 3µA,
backlight 40mA max
Operating Temperature
0°C to +50°C
Storage Temperature
-20°C to +70°C
Supply voltage (pin 1)
2.7 3.3VDC
Low Speed Count Input (pin 2)
Contact closure/open collector input,
30Hz max, negative edge triggered,
0.7V threshold 18V max, 15mS min.
pulse length
Electronic Count Input (pin 3)
10kHz max, positive edge triggered,
0.7V threshold, 18V max, 50µS min.
pulse length, TTL/CMOS compatible.
Reset Input (pin 4)
Contact closure/open collector, negative
edge triggered, 0.7V threshold 18V
max, 15mS min. pulse length
Common (pin 5)
Supply 0V and signal common.
Backlight (pin 6) (optional)
9V or 5V: see below
Specification
Backlight
5
6
+5V
0V
green: 9V or 5V
* 1201/2W
blue: 9V only
5
6
+9V
0V
*
5
6
+9V
0V
3
Supply
Voltage
5V Regulator 220 ¼WW
0.47 µF 3V
5
3
4
1
100nF
100nF
Max Signal Voltage 18V
High Speed
Pulses
Remote
Reset
CMOS/TTL
Inputs
Mount the 100nF (transient suppression) capacitor as close to the unit as possible.
The low speed input (pin 2) should always be used for contact closure because this is the
only input which contains de-bounce circuitry.
Examples
Remote
Reset
Low Speed Input
utilising integral
De-bounce Circuitry
2
4
5

Especificaciones del producto

Marca: Trumeter
Categoría: Equipo de medición
Modelo: HED261

¿Necesitas ayuda?

Si necesitas ayuda con Trumeter HED261 haz una pregunta a continuación y otros usuarios te responderán




Equipo de medición Trumeter Manuales

Equipo de medición Manuales

Últimos Equipo de medición Manuales